SOMFY Roller Blind Manuale utente
somfy
Roller Blind - Installation/Program Guides
Stay up to date with the online version
https://poweredblinds-somfy.swipeguide.com/guide/roller-blind-installationprogram-
guides
Version 41 | en_USCreated 2/1/2022 10:24 AM
Table of Contents
Roller Blind Installation Guide 3
Simplicity Roller Blind Installation Guide 12
Adjust the Uppper Stop Position 16
Adjust the Lower Stop Position 18
Set a 'MY' Position 20
Somfy Rollup Motor Reset 22
Somfy Rollup 28 Motor Control Programming 25
Pairing-Deleting A Single Channel Control 25
Pairing-Deleting A Multi Channel Control 27
Delete All Recorded Controls And Pair A New Control-Channel 29
Version 41 2
Roller Blind Installation Guide
Step 1 / 14
Check the blind type (standard, cassette) and fabric
match your order and the dimensions are correct.
Each blind will have the following components:
• Standard roller blind: 2 x universal brackets
• Cassette roller blinds: Blind up to 1M: 2 brackets,
blind 1M to 2M: 3 brackets, blind over 2M: 4 brackets.
• Screws and rawl plugs
Step 2 / 14
Somfy Motor
The Somfy motor powering your roller blind has an
integral rechargeable li-ion battery.
The battery within the motor is supplied with enough
charge to provide blind operation before a recharge is
required.
The program/reset button on the motor will vary
depending on the model and charger connection. The
images show the different buttons, however the
procedure when pressing the buttons is exactly the
same.
Version 41 3
Step 3 / 14
Charging the Motor
When the batteries are running low, the motor
program/reset button will blink red slowly for 3
seconds before and after blind operation.
To charge the motor battery:
• Connect the charger to the motor cable
• The LED on the charger will light up as follows:
• Solid Red = Charging
• Solid Orange = Charging is near completion
• Solid Green = Charging is complete
• Disconnect the cable when charging is complete
Warning
Do not operate the blind while the
motor is charging
Step 4 / 14
STANDARD ROLLER BLIND INSTALLATION
Marking and tting the brackets
Put the blind into the corresponding ends of the
brackets, then offer the blind into the position where it
will t in your window.
Mark the positions of 2 holes per bracket for xing or
drilling.
Secure the brackets in place at the marks previously
made.
Fix the brackets in place using the screws supplied.
Tip
If securing the brackets to plaster, brick,
stone, etc., drill the holes at the marked
positions using a 5.5mm masonry drill bit
and insert the raw plugs supplied.
Version 41 4
Step 5 / 14
STANDARD ROLLER BLIND INSTALLATION
Mounting the roller blind
Hold the blind to the brackets with the fabric in the
correct position based on your order (front or rear roll)
– the motor program/reset button should be
accessible from the front.
1. Secure the idle end (opposite the motor end) into
position by locating the ‘+’ shaped plunger into the ‘+’
shaped part of the bracket. When correctly aligned,
the plunger should pop into the bracket and secure in
place.
2. Now angle the motor head side into position and
slot the prongs of the motor head plate into the
bracket, ensuring that the central prong drops into
position on the bracket.
Warning
Important note: Ensure that the plunger
at the idle end (opposite the motor
end) is depressed by at least 5mm
when marking the hole positions.
Tip
Make sure the 'Somfy' logo on the motor
plate is orientated 'UP' for easy coupling
with the bracket.
Version 41 5
Step 6 / 14
CASSETTE ROLLER BLIND INSTALLATION
Bracket Types
There are two bracket options for open cassette
blinds, face x and top x.
For a blind up to 1 metre wide attach two brackets
tted approximately 75mm from each end of the
blind. Additional brackets with blinds >1M wide
should be spaced evenly between these:
• Up to 1M = 2 brackets
• >1M to 2M = 3 brackets
• >2M = 4 brackets.
Step 7 / 14
CASSETTE ROLLER BLIND INSTALLATION
The release lip on the bracket must face the back of
the blind.
Use the supplied screws per bracket ensuring that the
brackets are level.
Remember to allow room for the blind to clear any
obstacles when deployed, e.g. door or window
handles.
Version 41 6
Step 8 / 14
CASSETTE ROLLER BLIND INSTALLATION
Marking and tting the top & face x brackets
SPACING - Mark 2 x brackets approx 75mm in from
each end, with any additional brackets spaced evenly
between them.
TOP FIX - Position each bracket from the centre of the
xing hole a minimum distance of 45mm from the
back of any obstruction and with the lip to the back.
Mark the position of the holes, then secure in place.
FACE FIX - Position the back of your bracket against
the wall to the height of the blind drop, then mark the
position of the holes and secure the brackets in place.
Step 9 / 14
CASSETTE ROLLER BLIND INSTALLATION
Fitting the cassette
Once all the brackets are in place offer the blind to the
brackets. With the cassette tilted away from you
locate the front lip into the bracket and push upwards
to click the cassette into the back lip of the bracket.
Step 10 / 14
CASSETTE ROLLER BLIND INSTALLATION
Mounting the roller assembly
Hold the roller assembly to the brackets within the
cassette prole with the fabric in the correct position
based on your order (front or rear roll) – the motor
program/reset button should be accessible from
Version 41 7
below.
1. Secure the idle end (opposite the motor end) into
position by locating the ‘+’ shaped plunger into the ‘+’
shaped part of the bracket. When correctly aligned,
the plunger should pop into the bracket and secure in
place.
2. Now angle the motor head side into position and
slot the prongs of the motor head plate into the
bracket, ensuring that the central prong drops into
position on the bracket.
Warning
Important note: Ensure that the plunger
at the idle end (opposite the motor
end) is depressed by at least 5mm
when marking the hole positions.
Tip
Make sure the 'Somfy' logo on the motor
plate is orientated 'UP' for easy coupling
with the bracket.
Version 41 8
Step 11 / 14
POWER UP & TESTING
Your roller blind is tested to ensure it is operating
correctly prior to dispatch. During this process, the
upper and lower stop positions are preset based on
your height measurement. We also pair the control
ordered to the motor (if a control was ordered).
Wake up the motor
To preserve battery charge, the motor is supplied in
‘Sleep Mode’ and requires waking up once the blind is
tted and ready to operate.
To wake up the motor, briey press the program/reset
button on motor head - the blind will jog briey Up/
Down and is ready to operate.
Step 12 / 14
BLINDS SUPPLIED WITH A CONTROL
If you ordered a Somfy control with your blind(s), then
the control supplied will be paired to the motor. Once
you have woken the motor up, test your blind by
pressing the down button on your control.
The blind will travel down and stop at the factory
preset position (this can be adjusted).
Use the directional buttons to test operation.
Tip
Refer to the ‘Adjusting the stop positions’
section to ne tune the stop positions to
your desired position.
Version 41 9
Step 13 / 14
BLINDS SUPPLIED WITHOUT A SOMFY CONTROL
If you didn’t order a control with your blind(s), then the
control you already have requires pairing to the blind.
The blind supplied has been set up with the up/down
direction correctly dened and the stopping positions
preset.
• Wake the motor up (see previous step)
• Briey press the Up & Down buttons together on
your control and release – the blind will jog Up/Down.
• Briey press the program button on the back of the
control – the blind will jog Up/Down.
• The control is now paired to the blind motor.
Use the directional buttons to test operation and refer
to the ‘Stop Position Adjustment’ section to ne tune
the stop positions to your desired position.
Version 41 10
Indice
Altri manuali SOMFY Tenda per finestra
SOMFY
SOMFY Glydea DCT Guida all'installazione
SOMFY
SOMFY Sonesse 40 RTS Manuale utente
SOMFY
SOMFY Mornin Manuale utente
SOMFY
SOMFY WireFree Solar Pack Manuale utente
SOMFY
SOMFY Roll Up WireFree RTS Manuale utente
SOMFY
SOMFY Junior RU 30 RTS Manuale utente
SOMFY
SOMFY Clever Manuale utente
SOMFY
SOMFY Sonesse 40 RTS Manuale utente
SOMFY
SOMFY Movelite RTS Manuale utente
SOMFY
SOMFY RS485 Setting Tool Manuale utente
SOMFY
SOMFY CTS 40 Manuale utente
SOMFY
SOMFY Sunea RTS CMO Manuale utente
SOMFY
SOMFY Junior RU 30 RTS Manuale utente
SOMFY
SOMFY Sonesse 40 WF RTS Li-ion Manuale utente
SOMFY
SOMFY Altus Manuale utente
SOMFY
SOMFY Sonesse 40 RTS Manuale utente
SOMFY
SOMFY 1241752 Manuale utente
SOMFY
SOMFY Sonesse Ultra 50 RTS Istruzioni operative
SOMFY
SOMFY Smoove 1 RTS Manuale utente
SOMFY
SOMFY ROLLECTRIC II Manuale utente
