Sony DFP-R3000 Manuale utente

SDDS Player System

DIGITAL FILM SOUND READER

DFP-R3000

INSTALLATION MANUAL

1st Edition (Revised 1)

Serial No. 10001 and Higher

!WARNING

This manual is intended for qualified service personnel only.

To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that

contained in the operating instructions unless you are qualified to do so. Refer all servicing to

qualified service personnel.

!WARNUNG

Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.

Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die

Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei

Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen.Andere als die angegeben

Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung

dazu besitzen.

!AVERTISSEMENT

Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien.Afin

de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les

réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.

Pour toute réparation faire appel à une personne compétente uniquement.

This Digital Film Reader is classified as a CLASS 3A

LED PRODUCT.

Label is located on the top.

LED LIGHT

DO NOT STARE INTO BEAM OR VIEW

DERECTLY WITH OPTICAL INSTRUMENTS

CLASS 3A LED PRODUCT

LED-LICHT

NICHT IN DEN STRAHL BLICKEN

ODER MIT OPTISCHEN INSTRUMENTEN

EIN LED-PRODUKT

KLASSE 3A DIREKT ANSCHAUEN

LED Properties

Material : InGaAIP

Peak Wave length : 644 nm (Spectral Line Half Width ∆λ 18nm)

Emission duration: Continuous

LED output power: 2.41 mW (max)

Beam divergence : (H) 60 d(V) 10 d

1 (E)

DFP-R3000

Table of Contents

Manual Structure

Purpose of this manual ........................................................................................ 2 (E)

Related manuals................................................................................................... 2 (E)

Installation

1. Operating Environment .........................................................................1-1 (E)

2. Power Supply ........................................................................................1-1 (E)

3. Dimensions............................................................................................1-1 (E)

4. Input/Output Signals of Connector .......................................................1-2 (E)

5. Installation.............................................................................................1-3 (E)

5-1. Use of DFP-R3000 for 70 mm Film ..........................................1-3 (E)

5-2. Installation to the Projector........................................................1-7 (E)

5-2-1. Installing to SIMPLEX 35 (Strong International)................1-8 (E)

5-2-2. Installing to SIMPLEX 70 .................................................1-13 (E)

5-2-3. Installing to CENTURY JJ (Strong International).............1-15 (E)

5-2-4. Installing to NORELCO AA-II 35/70 (Kinoton) ...............1-17 (E)

5-2-5. Installing to V5/V8/V9 (CINEMECCANICA)..................1-20 (E)

5-2-6. Installing to P35 (Christie) .................................................1-23 (E)

5-3. Connecting to DFP-D3000 ......................................................1-26 (E)

5-4. Checking and Adjustment After Installation ...........................1-27 (E)

5-4-1. Film Running Checking .....................................................1-27 (E)

5-4-2. Error Rate Checking...........................................................1-29 (E)

5-4-3. Lip Sync Adjustment..........................................................1-30 (E)

5-4-4. Setting Up...........................................................................1-32 (E)

2 (E) DFP-R3000

Purpose of this manual This manual is the Maintenance Manual of the Digital Film Sound Reader DFP-

R3000.

This manual is intended for use by trained system and service engineers, describes

the information when installing DFP-R3000.

Related manuals ..

.DFP-R3000/DFP-D3000 Operation Manual (Supplied with the DFP-

D3000)

This manual is necessary for application and operation of the DFP-R3000.

.DFP-R3000 Maintenance Manual (Prepared separately)

This manual describes the information of the DFP-R3000 and the information that

premise the service based on parts.

.DFP-D3000 Maintenance Manual (Prepared separately)

This manual describes the inspection of the DFP-D3000 and the information that

premise the service based on parts.

.DFP-D3000/R3000 Quick Start Guide (Prepared separately)

This Quick Start Guide is intended to assist experienced cinema engineers in

systematically installing, setting up, and maintaining the DFP-3000 cinema

processor system.

Unless otherwise specified, all names of companies and products are trademarks or registered trademarks of the respective

companies.

Manual Structure

1-1 (E)

DFP-R3000

2. Power Supply

Power supply voltage : DC +24 V (This power is supplied

when connected to the DFP-

D3000.)

DFP-R3000 does not have POWER switch. Therefore, the

power ON/OFF of the DFP-R3000 is switched at the DFP-

D3000.

If the power of the DFP-R3000 needs to be turned OFF

when fault occurs, turn OFF the power of the DFP-D3000.

Power consumption : 9.6 W

1. Operating Environment

Operating temperature : 5 dC to 40 dC

Operating humidity : 10 % to 90 % (relative humidity)

Storage temperature : _20 dC to +60 dC

Mass (weight) : 3.5 kg

Locations to Avoid

Areas where the unit will be exposed to direct sunlight or

any other storong lights.

Dusty areas or areas where it is subject to vibration.

Areas with strong electric or magnetic fields.

Areas near heat sources.

Areas subject to electrical or RF.

Areas subject to static electricity noise.

3. Dimensions

Installation

240

156

176

DIGITAL FILM SOUND READER DFP-R3000

Unit : mm

1-2 (E) DFP-R3000

4. Input/Output Signals of Connector

SDDS I/F : DME 5W1S, female

Signal level ; SDI format digital audio signal

Pin No. I/O Signal Description

1I+24 V DC 24 V

2 — NC No connection

3 — GND Ground (DC 24 V)

4 — CABLE SHIELD Ground (Frame)

A1 O DATA SDDS data

G1 — DATA GND Ground (Data)

21A1

34G1

1-3 (E)

DFP-R3000

5-1. Use of DFP-R3000 for 70 mm Film

To use the DFP-R3000 for 70 mm film, the front panel,

and roller guide need to be replaced, etc.

Replace according to the following “Procedure”.

Required Parts

Front panel (70) assembly ;

1 (Sony part No. X-3168-037-1)

Front panel (70) R ; 1 (Sony part No. 3-200-455-01)

Optional guide assembly (70) ;

1 (Sony part No. X-3168-071-1)

Optional guide T assembly (70) ;

1 (Sony part No. X-3168-074-1)

Support ; 5 (Sony part No. 3-194-814-01)

Washer (SW4) ; 1 (Sony part No. 7-623-210-22)

Screw (B3 x 4) ; 6 (Sony part No. 7-682-545-04)

Required Tools

Philips screwdriver

Nut driver (d = 5 mm)

Hex wrench screwdriver (across ; 3 mm)

5. Installation

The following describes how to install the DFP-R3000 to

the various projectors indicated below.

1. Strong International : Simplex 35/70

Century JJ

2. Kinoton : Noleroco AA-II35/70

3. Cinemeccanica : V9, V8, V5

4. Christie : P35

Install the DFP-R3000 to a projector according to the

following procedure.

Installation Procedure

Installation to projector

↓

Connecting to DFP-D3000

↓

Checking and adjustment after installation

Notes on Installation

.Use the adapter (A) (Supplied with DFP-R3000) or

adapter (EA) (Prepared separately) supplied when

installing the DFP-R3000.

However, parts additional to adapter (A)/adapter (EA)

will be required for some projectors.

Checks the parts required in the procedure for installing

to projectors in “5-2. Installation to the Projector”.

.Attach the adapter (A)/adapter (EA) using the special

tool.

1-4 (E) DFP-R3000

Procedure

Step 1. Removing the Front Panel, Guide Rollers S3 and T1 and etc.

1. Remove the two screws (B3 x4) aand four screws (B2.6 x6) bto remove the right side panel.

2. Remove the two screws (B3 x4) cand four screws (B2.6 x6) d.

3. While holding the roller guide S2 to the direction of the arrow, remove the front panel assembly.

4. Remove the two escutcheons to the direction of the arrow.

5. Remove the one screw (RK4 x8), ornamental washer and washer to take out the roller guide S3

assembly and roller guide shaft S3 (35).

6. Remove the one screw (RK4 x8), ornamental washer and washer to take out the roller guide T1

assembly.

7. Remove the hexagon cap screw (4 x10), washer (W4) and spring washer (SW4) from inside

of the unit to take out the roller guide shaft T1 (35).

Front panel assembly

Escutcheon

Hexagon cap screw

4 x10

Escutcheon

Washer

Ornamental

washer

Roller guide

shaft S3 (35)

Roller guide S3

assembly

Roller guide T1 assembly

B2.6 x6 b

SW4

B3 x4 c

B2.6 x6 d

B3 x4 a

RK4 x8 Ornamental washer

Washer

Left side panel

Roller guide shaft T1 (35)

RK4 x8

Roller guide S2

1-5 (E)

DFP-R3000

Step 2. Attaching the Optional Guide Assembly (70) and Optional Guide T Assembly (70)

1. Attach the optional guide assembly (70) to the position from which the roller guide shaft S3 (35) was

removed.

2. Attach the optional guide T assembly (70) using hexagon cap screw (4 x10), spring washer (SW4)

and washer (W4) from inside of the unit to the position from which the roller guide shaft T1 (35) was

removed.

Hexagon

cap screw

4 x10

Optional guide T assembly (70)

Optional guide assembly (70)

SW4

1-6 (E) DFP-R3000

Step 3. Attaching the Front Panel (70) Assembly and Front Panel (70) R

1. Attach the five supports to the unit as shown in the figure.

2. Attach the front panel assembly (70) assembly to the unit using the three screws (B3 x4) eand two screws (B2.6 x

4) f.

3. Attach the front panel (70) R to the unit using the three screws (B3 x4) gand two screws (B2.6 x4) h.

4. Attach the right side panel removed at the procedure 1 of Step 1 using the two screws (B3 x4) aand four screws

(B2.6 x6) b.

Front panel (70) assembly

Front panel (70) R

Supports

Places for installing support

B3 x4 e

B3 x4 eB3 x4 e

B3 x4 g

B2.6 x4 h

B2.6 x4 f

B2.6 x6 b

B3 x4 a

Right side panel

DIGITAL FILM SOUND READER DFP-R3000

Diagram of completion

Altri manuali per DFP-R3000

Indice

Altri manuali Sony Lettore di schede

Manuali Lettore di schede popolari di altre marche

Lindy

Lindy 43185 Manuale utente

Lindy

Lindy 43185 Manuale utente

ViziT

ViziT RD-4F Manuale utente

Jinmuyu Electronics

Jinmuyu Electronics MR811 Series Manuale utente

AVID ID

AVID ID AVID1043 Manuale utente

Conrad

Conrad PCMCIA Manuale utente

Rosslare

Rosslare DR-6255 Manuale utente

Lindy

Lindy 51541 Manuale utente

Diapro T?bbi Ürünler

Diapro T?bbi Ürünler Across System Manuale utente

Johnson Controls

Johnson Controls Kantech tyco ioSmart Manuale utente

ACS

ACS ACR122L Manuale utente

Secukey

Secukey S2-MF Manuale utente

Elecom

Elecom MR-SMC07 series Manuale utente

Alien

Alien ALR-9800 Manuale utente

ACS

ACS ACR310 Manuale utente

Datamars

Datamars R-IN1300 MID Manuale utente

Alarm Lock

Alarm Lock AL-PRE2 Manuale utente

xpr

xpr B100PROX-AH Guida utente