Sony BKMW-E3000 Manuale utente
NETWORK INTERFACE BOARD
BKMW-E3000
INSTALLATION MANUAL
1st Edition
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
1 (E)
BKMW-E3000
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 2 (E)
Related manuals................................................................................................... 2 (E)
1. Installation
1-1. Installation Notes .................................................................................. 1-1 (E)
1-1-1. Confirmation Before BKMW-E3000 Installation ................ 1-1 (E)
1-1-2. Installation Flow Chart .........................................................1-4 (E)
1-1-3. Components and Connection Cable .................................... 1-5 (E)
1-1-4. Switch Setting and Function of LEDs on DSP-109 Board .. 1-6 (E)
1-1-5. Switch Setting and Function of LEDs on VN-13 Board ...... 1-7 (E)
1-2. Installation Procedures .......................................................................... 1-8 (E)
1-2-1. Rear Side of the VTR ........................................................... 1-8 (E)
1-2-2. Front Side of the VTR ........................................................ 1-15 (E)
1-3. Setting after Installation ......................................................................1-18 (E)
1-3-1. Network Setting ................................................................. 1-18 (E)
1-3-2. Starting e-VTR Manager .................................................... 1-20 (E)
1-4. SNMP .................................................................................................. 1-22 (E)
1-4-1. Configuring SNMP (SNMP Agent Variables) ...................1-24 (E)
1-4-2. Configuring System Management Information
(SNMP MIB-2 Variables) ..................................................1-26 (E)
1-4-3. Configuring Trap Control
(Professional VTR Category Variables) ............................ 1-27 (E)
2 (E)
BKMW-E3000
Purpose of this manual
This manual is an installation manual of Network Interface Board BKMW-E3000.
This manual is intended for system and service engineers, and provides the informa-
tion that is required to install this unit.
Related manuals
Besides this “installation manual”, the following manuals are available for this unit.
If these manuals are required, please contact your local Sony Sales Office/Service
Center.
..
..
.Operation Manual (Supplied with this unit.)
This manual is necessary for application and operation (and installation) of this unit.
..
..
.Maintenance Manual (In common with the VTR, available on request)
Volume-1 : Service Instruction
Volume-2 : Parts List, Block Diagrams, and Board Layouts
Volume-3 : Schematic Diagrams
These manuals describe the maintenance and service information (service over-
view, adjustments, board layouts, schematic diagrams, detailed parts list, etc.) for
this unit.
..
..
.“Semiconductor Pin Assignments” CD-ROM (Available on request)
This “Semiconductor Pin Assignments” CD-ROM allows you to search for
semiconductors used in this unit.
Semiconductors that cannot be searched for on this CD-ROM are listed in the
maintenance manual (volume-2) for the corresponding unit. The maintenance
manual (volume-2) contains a complete list of all semiconductors and their ID
Nos., and thus should be used together with the CD-ROM.
Part number: 9-968-546-XX
Manual Structure
1-1 (E)
BKMW-E3000
Section 1
Installation
1-1. Installation Notes
1-1-1. Confirmation Before BKMW-E3000 Installation
BKMW-E3000 has the following features mainly:
.MXF D10 file receive/transmit (The receive function is applicable only for recorder.)
.Proxy AV file transmit
.Network service with Web server
.Network service with Windows application
.FTP/HTTP transmit by e-VTR control panel operation
.e-monitor
.Automatic get of network setting information such as IP address, and so on
.Network management using host names (DNS client service)
.Automatic file creation by reading data of the tape or memory label
.User registration
.Backup for setup menu settings
.SNMP
.Links to external servers using meta data
.Automatic file system data management through on external server ... etc.
However, of the VTRs to install the BKMW-E3000, some VTRs having early serial numbers have a
limitation by variations in designs of the EPR-1 boards.
The limitation is one of the following cases:
.The VTR cannot be equipped with the BKMW-E3000.
.MXF D10 file receive/transmit function is available, instead of unavailable SDTI-CP input/output
function of the VTR.
.SDTI-CP input/output function is available, instead of unavailable MXF D10 file receive/transmit
function of the BKMW-E3000.
Before installing the BKMW-E3000, please read thoroughly the following instructions.
1-2 (E) BKMW-E3000
EPR-1 board number suffix and installing pattern
1. Check the serial number of the VTR.
2. Check the part-number suffix of the EPR-1 board by using “Table-1: EPR-1 board number suffix and
serial number”or checking the EPR-1 board directly.
Table-1: EPR-1 board number suffix and serial number
EPR-1 board number suffix
Model -12 -13 -14 and later
MSW-2000 ——10001 -
MSW-A2000P 41001 - 42080 42081 - 42212 45001 -
MSW-A2000 11001 - 11030 —15001 -
MSW-M2000P 40001 - 40975 40976 - 41472 45001 -
MSW-M2000 10001 - 10460 10461 - 10655 15001 -
MSW-M2100P 40001 - 40495 40496 - 41052 45001 -
MSW-M2100 10001 - 10230 10231 - 10345 15001 -
n
In case of earlier serial number than the above number of suffix -12, the VTR cannot be equipped with
the BKMW-E3000.
3. Check the installing pattern.
In case the EPR-1 board number suffix is -14 and later:
All functions can be used.
In case the EPR-1 board number suffix is -12 or -13:
Select either of the MXF D10 file receive/transmit function or SDTI-CP input/output function.
Table-2: Installing pattern check
m
.MXF D10 file receive/transmit function:
Receives and transmits the video, audio, or metadata recorded on the tape as MXF D10 file.
.SDTI-CP input/output function:
Receives and transmits the video, audio, or metadata recorded on the tape using SDTI-CP.
c
Depending on the installing pattern [A], [B] or [C], some installing procedures described in “1-2-1.
Rear Side of the VTR”are different. Attach the BKMW-E3000 correctly as directed in the procedures.
EPR-1 board
part number
Suffix -14 or later
Suffix -12 or -13
Function to select
Not necessary
(All functions can be used.)
Selects MXF D10 file receive/transmit function
Selects SDTI-CP input/output function
Installing pattern
Pattern [A]
Pattern [B]
Pattern [C]
1-3 (E)
BKMW-E3000
Confirming Version
1. Check the following software versions using the maintenance mode M30 of the VTR:
SY ROM Ver. ; V7.10 or higher
SV ROM Ver. ; V6.00 or higher
n
If the version is lower than the above, upgrade the software of the VTR.
Please contact your local Sony Sales Office/Service Center.
VTR Maintenance Mode
For the detailed information for each menu of the maintenance mode, refer to Section 3 of the mainte-
nance manual volume-1 of the VTR.
.Activating the maintenance mode:
Press S1500 (A-1) on the SS-89 board of the VTR.
.Entering a mode (menu):
Press the F5 (SET) button once under the asterisk cursor (*) is aligned to the desired mode (menu) with
the menu displayed on the video monitor.
The *mark is sifted by turning the MULTI CONTROL knob of the VTR.
.Existing a mode (menu):
Press the F6 (EXIT) button of the VTR several times to exit the mode (menu).
1-4 (E) BKMW-E3000
Modify the front panel.
Attach the SW-1106 board.
Attach the harness (HP-SW).
Attach the front panel (E).
1-3. Setting after Installation
Pattern [A] Pattern [B]
Pattern [C]
Pattern [A] and [B]
Attach
the IF-886
board.
Attach the IF-886
board after removing
the DIF-109 board.
Set the DIP switch
S101-4 of the VN-13
board assembly to “ON”.
Attaching to
the EPR-1
board
1Flow chart of the rear side of the VTR (Refer to Section 1-2-1)
1
2Flow chart of the front side of the VTR
(Refer to Section 1-2-2)
Attaching
ETHERNET
panel
Attach the IF-885 board.
Connect the connection cable
and harness (LED).
Attach the harness guard assembly.
Pattern [C]
Attach the ferrite clamp.
Attach the VN-13 board assembly.
Connect the connection code and harness (LED).
Connect the harness (EPR-VN).
2
Attach the ETHERNET panel.
(In hte case of the player ; Attach the blank sheet.)
Attaching the
VN-13 board
assembly
1-1-2. Installation Flow Chart
1-5 (E)
BKMW-E3000
12345
678
9
![
0
!- !=
1-1-3. Components and Connection Cable
Components
No. Name Remarks Section to be referred
1IF-886 board Not required in the case of installing pattern [C]. 1-2-1. Rear Side of the VTR
2IF-885 board
3ETHERNET*panel
4Blank sheet Not required in the case of the recorder.
5Connection cord
6Harness (LED)
7Harness guard assembly
8Ferrite clamp
9VN-13 board assembly
!/ Harness (EPR-VN) Not required in the case of installing pattern [C].
—Hexagonal support (4 pcs) For attaching 1
—Screw B3 x4 Not required in the case of installing patterns [B] and [C].
(10 pcs, 2 of them for spare)
—Screw BVTT3 x6 (8 pcs) For attaching 2and 3
!- Front panel (E) 1-2-2. Front Side of the VTR
!= SW-1106 board
1-6 (E) BKMW-E3000
1-1-4. Switch Setting and Function of LEDs on DSP-109 Board
DSP-109 Board (Side A)
Switches
n
Never change the setting of switches on “Factory use”.
Ref No. Bit Name Description Factory setting
S11 1 —Factory use OFF
2—Factory use ON
LEDs
LED No. Name Color Description Normal state
D1 —Yellow Lights while data is transmitted to Proxy AV file. —
D2 —Green Lights when the DSP (IC2/DSP-109 board) is not OFF
operating normally.
D3 —Red Blinks while data is transmitted to Proxy AV file. —
D4 —Green Blinks when the FPGA (IC1/DSP-109 board) is Blinks
operating normally.
D5 —Yellow Factory use —
D6 —Green Factory use —
D7 —Red Factory use —
D8 —Green Factory use —
D101 —Green Factory use OFF
S11
D101
D8 D7
D6 D5
D4 D3
D2 D1
A
B
C
D
E
F
G
H12345
Altri manuali per BKMW-E3000
1
Indice
Altri manuali Sony Hardware per computer
Sony
Sony BKPF-L752 Manuale utente
Sony
Sony VAIO PCWA-C800S Foglio di istruzioni
Sony
Sony PCM-1630 Manuale utente
Sony
Sony PCM-601ESD Manuale utente
Sony
Sony SMO-D501 Istruzioni operative
Sony
Sony HFBK-TS1 Manuale utente
Sony
Sony SVT-RS1A Manuale utente
Sony
Sony MVS-6530 Manuale utente
Sony
Sony CMOS CXP854P60 Manuale utente
Sony
Sony SDP-EP90ES Manuale utente
Sony
Sony DVCAM DSBK-2020K Manuale utente
Sony
Sony PCWA-C700 - Wireless Lan Dual Pc Card Scheda tecnica
Sony
Sony HMI-3000MT Manuale utente
Sony
Sony MSAC-PR1 Manuale utente
Sony
Sony IFB-X600E Manuale utente
Sony
Sony HFBK-SD1 Manuale utente
Sony
Sony BKDS-7200K1 Manuale utente
Sony
Sony XDBK-104 Manuale utente
Sony
Sony MDX-F5800 Manuale utente
Sony
Sony HKSR-5804 Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
