Sony BKMA-U70XGI Manuale utente
UPGRADE KIT FOR MAV-70
BKMA-U70XGI
INSTALLATION MANUAL
1st Edition
Serial No. 10001 and Higher
BKMA-U70XGI
!WARNING
This manual is intended for qualified service personnel only.
To reduce the risk of electric shock, fire or injury, do not perform any servicing other than that
contained in the operating instructions unless you are qualified to do so. Refer all servicing to
qualified service personnel.
!WARNUNG
Die Anleitung ist nur für qualifiziertes Fachpersonal bestimmt.
Alle Wartungsarbeiten dürfen nur von qualifiziertem Fachpersonal ausgeführt werden. Um die
Gefahr eines elektrischen Schlages, Feuergefahr und Verletzungen zu vermeiden, sind bei
Wartungsarbeiten strikt die Angaben in der Anleitung zu befolgen. Andere als die angegeben
Wartungsarbeiten dürfen nur von Personen ausgeführt werden, die eine spezielle Befähigung
dazu besitzen.
!AVERTISSEMENT
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin
de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les
réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres.
Pour toute réparation faire appel à une personne compétente uniquement.
1 (E)
BKMA-U70XGI
Table of Contents
Manual Structure
Purpose of this manual ........................................................................................ 3 (E)
Related manuals................................................................................................... 3 (E)
Contents ............................................................................................................... 3 (E)
Trademarks .......................................................................................................... 4 (E)
1. Downloading Parameters from the SY-253 Board
1-1. Precautions ............................................................................................ 1-1 (E)
1-2. Equipment Required.............................................................................. 1-1 (E)
1-3. Installing TeraTermPro (Version 2.3) ................................................... 1-2 (E)
1-4. Downloading Parameters from the SY-253 Board ............................... 1-2 (E)
2. Installing the Circuit Board and Parts
2-1. Installing the SY-253A Board and the PU-102A Board .......................2-1 (E)
2-2. Installing the Front Panel (Lower) ........................................................ 2-3 (E)
3. Checking Version
3-1. Equipment Required.............................................................................. 3-1 (E)
3-2. Checking Version ..................................................................................3-1 (E)
4. Uploading Parameters to the SY-253A Board
4-1. Equipment Required.............................................................................. 4-1 (E)
4-2. Uploading Parameters to the SY-253A Board ...................................... 4-1 (E)
5. Logical Formatting
3 (E)
BKMA-U70XGI
Purpose of this manual
This manual is the installation manual of the Upgrade Kit BKMA-U70XGI that is
used to upgrade the Multi Access Video Disk Recorder MAV-70 to be equivalent to
the MAV-70XGI.
This manual is intended for use by the trained system and service engineers, and
describes the information regarding installation.
Related manuals
Besides this Installation Manual, the following manuals are available for the
BKMA-U70XGI.
..
..
.MAV-70/BKMA-PS70 Installation Manual (Supplied with MAV-70)
This manual describes the information that is required for installation of the
MAV-70 and the Redundant Power Supply Unit (BKMA-PS70).
..
..
.MAV-70/BKMA-7010/7020/7030/7040/7045/7050/7060/7070/PS70
Maintenance Manual Volume 1 (Available on request)
..
..
.MAV-70XGI Series
Maintenance Manual (Available on request)
This manual describes the information that premise the service based on parts
replacement (diagnostics, parts replacement, electrical alignment and circuit
description, etc.)
If this manual is required, please contact your local Sony Sales Office/Service
Center.
Contents
The following is a summary of all the section for understanding the contents of this
manual.
Section 1 Downloading Parameters from the SY-253 Board
Explains the procedure to download the data that are set in the SY-253 board.
Section 2 Installing the Circuit Board and Parts
Explains the procedure to install the circuit board and to replace the front panel
(lower).
Section 3 Checking Version
Explains how to check the version.
Section 4 Uploading Parameters to the SY-253A Board
Explains the procedure to upload the data to the SY-253A board.
Section 5 Logical Formatting
Explains the procedure of logical formatting.
Manual Structure
4 (E) BKMA-U70XGI
Trademarks
Registered trademarks used in this manual are follows.
.Ethernet is a registered trademark of Xerox Corporation.
.
Windows and Windows NT are the registered trademarks of Microsoft Corporation.
1-1 (E)
BKMA-U70XGI
Section 1
Downloading Parameters from the SY-253 Board
1-1. Precautions
.Contents of this installation manual premises that the replacement of the circuit board using the
BKMA-U70XGI and the version upgrade in order to increase capacity of hard disks such as the
BKMA-U70/36 are going to be implemented simultaneously.
Note that all the materials that have already been stored in the hard disks will be erased when the hard
disks are upgraded of the version.
When the circuit board is replaced using the BKMA-U70XGI, the data that have been stored in the SY-
253 board must be downloaded and then be uploaded to the SY-253A board in order to transfer the
data.
.Shut down the system and turn off the main power of the MAV-70 before starting the circuit board
replacement work using the BKMA-U70XGI.
1-2. Equipment Required
(The software TeraTermPro and the data downloading program are contained in the CD-ROM supplied.)
.Personal computer (Windows95/98/2000/NT4.0)
.RS-232C cross cable
.TeraTermPro (Version 2.3)
.GetSyPr10.ttl (SY253 Data Download Macro)
n
The CD-ROM supplied, contains the following files.
.GetSyPr10.ttl (SY253 DataDownload Macro)
.PutSyPr10. (SY253 DataUpload Macro)
.VfySyPr10.ttl (SY253 Data Verify Macro)
Cables
Connectors on a personal computer side
D-sub 9-pin, male 1-560-651-00 (connector)
1-561-749-00 (shell)
Connectors on a MAV-70 side
D-sub 9-pin, female 1-562-565-00 (connector)
1-561-749-00 (shell)
(D-sub 9-pin, female)(D-sub 9-pin, male)
RXD
TXD
GND
1
2
3
4
5
6
7
8
9
NC
RXD
TXD
NC
GND
NC
NC
NC
NC
1
2
3
4
5
6
7
8
9
.Personal computer side .MAV-70 side
1-2 (E) BKMA-U70XGI
1-3. Installing TeraTermPro (Version 2.3)
1. Copy the “Tools/ttermp23” folder and all the folders and files under it that are contained in the CD-
ROM supplied, to TEMP or the desired folder of a personal computer.
2. Click “setup.exe” in the “ttermp23” folder.
TeraTermPro (version 2.3) is installed in a personal computer.
3. Copy the “SY253data” folder in the “Tools/TeraTerm/” in the CD-ROM supplied, to the same folder
where the TeraTermPro (version 2.3) is installed.
n
In order to start up TeraTermPro (version 2.3), click “ttermpro.ex” in the “Ttermpro” folder.
1-4. Downloading Parameters from the SY-253 Board
1. Remove the ornamental panel (A) from the MAV-70.
(Refer to Section 2-2-1 of the Maintenance Manual Volume 1.)
2. Set the switch S3 on the front panel of the MAV-70 to INT.
3. Connect the MAV-70 to a personal computer with the RS-232C cross cable.
4. Turn on the main power of the MAV-70.
5. Start up TeraTermPro (version 2.3).
6. The Tera Term New connection display appears. Click “serial” and press the [OK] button.
1-3. Installing TeraTermPro (Version 2.3)
1-4. Downloading Parameters from the SY-253 Board
COM1 RS-232C cable (9P-9P)
Personal Computer
1-3 (E)
BKMA-U70XGI
7. The Tera Term Serial port setup display appears. Set the communication conditions as follows and
press the [OK] button.
Port COM1
Baud rato 38400
Data 8 bit
Parity none
Stop 1 bit
Flow Control none
8. From the Top Menu, select [Control] _[Macro].
9. From the Macrofile selector display, select “Sy253data/GetSyPr10.ttl”and press [Open].
The “Macro GetSyPr10.ttl”is executed and the parameters contained in the SY-253 board is copied
to a personal computer.
1-4. Downloading Parameters from the SY-253 Board
Indice
Altri manuali Sony Registratore digitale
Sony
Sony DSR-DR1000 Manuale utente
Sony
Sony DNW-A25 Manuale utente
Sony
Sony Walkman GV-8 Manuale utente
Sony
Sony Giga Pocket Manuale utente
Sony
Sony VR-510U Manuale utente
Sony
Sony Handycam HDRSR11 Manuale utente
Sony
Sony DNW-A100 Manuale utente
Sony
Sony HANDYCAM DCR-DVD650 Manuale utente
Sony
Sony Handycam HDR-CX240 Manuale utente
Sony
Sony DSR-2000AP Manuale utente
Sony
Sony HVO1000MD Manuale utente
Sony
Sony HSR-X200P Manuale utente
Sony
Sony DHG-HDD250 - 30-Hour High-Definition Digital Video... Manuale utente
Sony
Sony SVR-3000 - Digital Network Recorder Manuale utente
Sony
Sony SVR-3000 - Digital Network Recorder Manuale utente
Sony
Sony DHG-HDD250 - 30-Hour High-Definition Digital Video... Manuale utente
Sony
Sony HVR-S270E Manuale utente
Sony
Sony HVO1000MD Manuale utente
Sony
Sony MAV-555SS Manuale utente
Sony
Sony SVR-2000 Manuale utente
