Sony SS-SP50FW Manuale utente
FLAT WIDE DISPLAY
FWD-50PX2
PROTOCOL MANUAL
1st Edition
FWD-50PX2
Table of Contents
1. Communication Parameter ................................................................ 1
2. Pin Configuration ..................................................................................... 1
3. Communication Data Format ........................................................... 1
4. General Function ..................................................................................... 3
5. Picture/Sound .......................................................................................... 12
6. Size/Shift .................................................................................................... 14
7. Status Enquiry ........................................................................................ 16
8. User Reset ................................................................................................. 19
1
FWD-50PX2
1. Communication Parameter
Communication system RS-232C
Synchronous system Asynchronous communication
Baud rate 9600 bps
Character length 8 bit
Parity None
Start bit 1 bit
Stop bit 1 bit
Flow control None
2. Pin Configuration
12345
Display side (D-sub 9-pin)
_External view _
6789
12345
6789
Host side (D-sub 9-pin)
_External view _
FWD-50PX2
Personal computer
Pin No. Signal
1NC
2TD
3RD
4NC
5 GND
6NC
7NC
8NC
9NC
Pin No. Signal
1NC
2RD
3TD
4NC
5 GND
6NC
7NC
8NC
9NC
3. Communication Data Format
(a) Control (Host →Request of Write to Display)
No. Item Value
1 Header 0x8C:Control
2 Category 0xXX
3 Function 0xXX
4 Data1 (Length) 0xXX
5 Data2 (Data1) 0xXX
: : 0xXX
: : 0xXX
X DataX 0xXX
X+1 Check Sum 0xXX
*Check Sum: The total from No. 1 to No. X, when value exceeds 255,1byte
of data is confirmed the bottom.
*Set the command interval to 500 ms or more when transmitting the
Control command continuously.
*Set the command interval to 500 ms or more when transmitting the same
command (Enquiry) after the Control command.
(b) Enquiry (Host →Request of Read to Display)
No. Item Value
1 Header 0x83:Enquiry
2 Category 0xXX
3 Function 0xXX
4 Data1 0xFF
5 Data2 0xFF
6 Check Sum 0xXX
*Check Sum: The total from No.1 to No.5, when value exceeds 255, 1byte
of data is confirmed the bottom.
2FWD-50PX2
(c) Answer (Display →Response to Host)
1Control answer
No. Item Value
1 Header 0x70: Answer
2 Answer*0x00: Completed
0x01: Limit Over
0x02: Limit Under
0x03: Command Canceled
3 Check Sum 0xXX
*0x00:Completed Normal response.
0x01:Limit Over The packets was received normally, but the
data value was over the upper limit.
Forcedly the monitor adjusted the data to
maximum value.
0x02:Limit Under The packets was received normally, but the
data value was under the lower limit.
Forcedly the monitor adjusted the data to
minimum value.
0x03:Command Canceled The packets was received normally, but the
command was cancelled because the function
was not in adjustable mode, such as “_” a
function displayed as in user menu.
*Check Sum: The total from No.1 to No.2, when value
exceeds 255, 1byte of data is confirmed the
bottom.
2Enquiry answer (Complete)
No. Item Value
1 Header 0x70: Answer
2 Answer 0x00: Completed
3 Return Data Size 0xXX
4 Return Data1 0xXX
: : 0xXX
: : 0xXX
X Return DataX 0xXX
X+1 Check Sum 0xXX
*0x00: Completed Normal response.
*Return Data returns the read value.
*Check Sum: The total from No.1 to No.X, when value exceeds 255,1byte
of data is confirmed the bottom.
3Enquiry answer (Command cancel)
No. Item Value
1 Header 0x70: Answer
2 Answer 0x03: Command Canceled
3 Check Sum 0xXX
*0x03: Command Canceled The packets was received normally, but the
command was cancelled because the function
was not in adjustable mode, such as “_” a
function displayed as in user menu.
*Check Sum: The total from No.1 to No.2, when value
exceeds 255, 1byte of data is confirmed the
bottom.
4Error answer
No. Item Value
1 Header 0xE0: Answer
2 Answer*0x00: No Function Error
0x01: Check Sum Error
0x02: Data Length Error
3 Check Sum 0xXX
*0x00: No Function Error Packet header, category of function codes do not
exist in this protocol.
0x01: Check Sum Error The “Check Sum” value of the packet which
received is wrong.
0x02: Data Length Error The “Data Num” value of the packet which
received is wrong.
3
FWD-50PX2
4. General Function
(a) Mode Control
Syntax Header Category Function Data1 Data2 Check Sum
Control 0x8C 0x00 Code Table(1-a)[a] 0x02 Code Table(1-a)[b] 0xXX
Enquiry 0x83 0xFF 0xFF 0xXX
Answer Header Answer Check Sum
Control 0x70 0x00 0x70 Completed
0x70 0x01 0x71 Limit Over
0x70 0x02 0x72 Limit Under
0x70 0x03 0x73 Command Canceled
Answer Header Answer Return to Data Size Return Data1 Check Sum
Enquiry 0x70 0x00 0x02 Code Table(1-a)[b] 0xXX Completed
Code Table(1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x00 Power*10x00 OFF Yes Yes Enable Enable
0x01 ON
0x01 Input Select*20x0A INPUT2 RGB Yes Yes Disable Enable
0x0B INPUT2 COMPONENT
0x0C OPTION1 VIDEO
0x0D OPTION1 S VIDEO
0x0E OPTION1 RGB
0x0F OPTION1 COMPONENT
0x10 OPTION2 VIDEO
0x11 OPTION2 S VIDEO
0x12 OPTION2 RGB
0x13 OPTION2 COMPONENT
0x20 INPUT1 DVI
0x02 Force Status Display 0x00 ON Yes Yes Disable Enable
0x01 OFF
0x03 Audio Mute 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x04 Auto Status Display 0x00 ON Yes Yes Enable Enable
0x01 OFF
0x05 Closed Caption 0x00 OFF Yes Yes Disable Enable
0x01 CC1
0x02 CC2
0x03 CC3
0x04 CC4 (Continued)
4FWD-50PX2
Code Table(1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x06 Color System 0x00 Auto Yes Yes Disable Enable
0x01 NTSC
0x02 NTSC4.43
0x03 PAL
0x04 SECAM
0x05 PAL-M
0x06 PAL-N
0x07 PAL60
0x0B Picture Inversion 0x00 OFF Yes Yes Disable Enable
0x01 Auto
0x02 On
0x0C Picture Orbit 0x00 OFF Yes Yes Disable Enable
0x02 ON
0x0D Orbit Range 0x00 Small Yes Yes Disable Enable
0x01 Middle
0x02 Large
0x0E Orbit Cycle 0x00 10 sec Yes Yes Disable Enable
0x01 30 sec
0x02 1 min
0x03 5 min
0x0F Language 0x00 Japanese Yes Yes Disable Enable
0x01 English
0x02 Deutsch
0x03 Français
0x04 Español
0x05 Italiano
0x10 Index Number 0x01-0xFF Yes Yes Disable Enable
0x13 Power Saving 0x00 Standard Yes Yes Disable Enable
0x01 Reduce
0x14 Speaker Out 0x00 ON Yes Yes Disable Enable
0x01 OFF
0x16 HD Mode 0x00 1080i Yes Yes Disable Enable
0x01 1035i
0x17 RGB Mode 0x00 DTV Yes Yes Disable Enable
0x01 PC
0x18 Sync Mode 0x00 H/Comp Yes Yes Disable Enable
0x01 Video
0x1B Clock Display 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x40 All White 0x00 OFF Yes Yes Disable Enable
0x01 ON (Continued)
5
FWD-50PX2
Code Table(1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x41 BackGroud 0x00 Gray Yes Yes Disable Enable
0x01 Dark Gray
0x02 Black
0x49 Auto Dimmer 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x65 IP Setting Mode 0x00 DHCP Yes Yes Enable Enable
0x01 Manual
0X02 Speed
0x66 IP Setting Execute 0x00 No No Yes Enable Enable
0x01 Yes
0x67 IP Setting Result 0x00 Done Yes No Enable Enable
0x01 Error 1 (UART Commu.)
0x02 Error 2 (Duplication)
0x03 Error 3 (IP Add Setting)
0x04 Error 4 (GW Add setting)
0x05 Error 5 (DNS1 Setting)
0x06 Error 6 (DNS2 Setting)
0x07 Error 7 (Sbnt Msk Setting)
0x68 Speed Setting 0x00 100Mbps/Full Duplex Yes Yes Enable Enable
0x01 100Mbps/Half Duplex
0x02 10Mbps/Full Duplex
0x03 10Mbps/Half Duplex
0x04 Auto
0x24 Input Detect (Option1) 0x00 U3 (HD15) No Yes Disable Enable
0x01 U1 (CVBS/Y, C)
0x02 U2 (BNC)
0x03 Reserved
0x04 FW31/FW32
0x05 FW50
0x06 Reserved
0x07 Reserved
0x08 Reserved
0x09 Reserved
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connected (Continued)
6FWD-50PX2
Code Table(1-a)
[a]Function [b]Range/Switch Code Command
Control Enquiry Standby Power On
0x25 Input Detect (Option2) 0x00 U3 (HD15) No Yes Disable Enable
0x01 U1 (CVBS/Y, C)
0x02 U2 (BNC)
0x03 Reserved
0x04 FW31/FW32
0x05 FW50
0x06 Reserved
0x07 Reserved
0x08 Reserved
0x09 Reserved
0x0A Reserved
0x0B Reserved
0x0C Reserved
0x0D Reserved
0x0E Reserved
0x0F Not Connect
0x26 Auto Shut OFF 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x27 Auto Screen Adjust 0x00 OFF Yes Yes Disable Enable
0x01 ON
0x28 Input Setting 0x00 Selectable Yes Yes Disable Enable
0x01 Fix
0x30 PAP 0x00 OFF Yes Yes Disable Enable
0x01 P&P
0x02 PinP
0x31 Active Picture 0x00 Left (P&P)/Main (PinP) Yes Yes Disable Enable
0x01 Right (P&P)/Sub (PinP)
0x02 Swap*2
0x32 Picture Size (P&P) 0x00-0x0E Yes Yes Disable Enable
0x33 Sub Picture Size (PinP) 0x00 Large Yes Yes Disable Enable
0x01 Small
0x34 Picture Position (PinP)*30x00 Position1 Yes Yes Disable Enable
0x01 Position2
0x02 Position3
0x03 Position4 (Continued)
Altri manuali per SS-SP50FW
3
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Sony TV a schermo piatto
Sony
Sony KE-50XS910 - 50" Flat Panel Color Tv Guida utente
Sony
Sony WEGA KDE-42XS955 Manuale utente
Sony
Sony Bravia KLV-V26A10E Manuale utente
Sony
Sony FD Trinitron Wega KV-32HS420 Manuale utente
Sony
Sony BRAVIA 4-168-148-15 (1) Manuale utente
Sony
Sony BRAVIA KDL-46V3000 Guida utente
Sony
Sony KDL-26N4000 - 26" LCD TV Manuale utente
Sony
Sony BRAVIA 4-160-344-11(1) Manuale utente
Sony
Sony KDL-32S2800 Manuale utente
Sony
Sony BRAVIA 4-151-686-13(1) Manuale utente
Sony
Sony WEGA KE-42M1 Manuale utente
Sony
Sony KDL-32XBR950 - 32" Flat Panel Lcd Wega™ Xbr... Manuale utente
Sony
Sony KDL-32S2400 - 32" Bravia Lcd Hdtv Manuale utente
Sony
Sony Bravia XBR-60LX900 Manuale utente
Sony
Sony BRAVIA 4-136-111-12(1) Manuale utente
Sony
Sony bravia X series Manuale utente
Sony
Sony BRAVIA KDL-46V2500 Guida utente
Sony
Sony KDL-40V2500 - Bravia V-series Lcd Hdtv Manuale utente
Sony
Sony BRAVIA KDL-26M4000 Manuale utente
Sony
Sony KDL-40V3000, KDL-46V3000 Manuale utente
