Soshine CPE206 Manuale utente
Wireless Bridge User Manual
Model: CPE206 | CPE355
Thank you for purchasing our product. Please read the user manual carefully before use.
Any problems, please contact us in time.
1. Typical Application
1.1 Typical Application
Our wireless bridges not only help you build remote monitoring systems, but also help you
extend your network signal to warehouses, barns, garages and other buildings near your
home.
1.2 Construction of Wireless Bridge System
1) Point to Point Connection:
A. Point to point long range video surveillance
B. Point to point long range network extend
C. Multiple network equipment long range access
2) Multiples Clients Connection
2. Wireless Bridges Main Characters
1) Long-distance 5.8G wireless transmission.
2) Support point-to-point, point-to-multipoint mode.
3) Compatible with both WDS networking mode and video networking mode.
4) Support auto-configure the transmitter and receiver, and also support the PC to finish
settings.
5) Dynamic MIMO power saving mode (DMPS) and automatic power saving transmission
(APST).
6) Pre-configured wireless bridge, plug and play.
7) Support 24V POE power supply, convenient installation and deployment, simply
construction, safe and reliable.
8) Wireless bridges can be repositioned and reused, flexible and cost effective.
3. Product Parameters
Model
CPE206 / CPE355
Master Control
Ar9344
DRAM:
DDR2 64MByte
FLASH
8Mbyte
Wire Interface
10/100Mbps LAN*2
CPE Transmission Rate
300Mbps
Transfer Method
Direct Sequence Spread Spectrum(DSSS)
Modulation
OFDM/BPSK/QPSK/CCK/DQPSK/DBPSK
Network Standard
IEEE802.11a, IEEE802.11b, IEEE802.11g ,IEEE802.11n
Supporting Agreement
CSMA/CA,TCP/IP,IPX/SPX,NetBEUI,DHCP,NDIS3,NDIS4,NDIS5
Frequency Range
4900-6100MHz
Power Consumption:
3W
Power Supply
POE 24V 0.5A-1A
Antenna Gain:
12DBi/14DBi
Antenna Polarization
Direction:
Vertical (Horizontal 60°C / Vertical 30°C )
Management Settings: WEP management, Telnet, Serial
Encryption
WEP encryption 64/128bits, WPA, WPA2,802.1x
Operating Temperature:
-30°C ~ 65°C
4. Operation Instruction
The two bridges are pre-paired at the factory. If they do not pair and connect automatically
when you receive the product, you can read the following instructions to pair and connect
them yourself.
There are two setting modes for wireless bridges: Auto-configuration mode and Custom
configuration mode.
A. Auto-configuration Mode: Simply connect the bridge with POE adapter and Internet
source, one select "A" mode and the other select "B" mode. Keep the master and slave both
in the same channel. The two bridges will be paired automatically without any other settings.
B. Custom Configuration Mode: You must be familiar with the network technology,
otherwise the bridges may lose the network or it will not work properly. This mode is mainly
used for reading parameters and debugging, also can be used to configure
point-to-multipoint video surveillance or network expansion (reserved function).
We strongly recommend you to choose auto-configuration mode when you use this product
for the first time. You can switch to custom mode after you understand the network settings.
4.1 Product Overview
The functions of CPE355 wireless bridge and CPE206 wireless bridge are basically the same.
Their main difference is that the antenna gain and product wireless connection status
indication are different.
1) CPE206 wireless bridge antenna gain is 12dbm, its unobstructed transmission distance is
2km.
2) CPE355 wireless bridge antenna gain is 14dbm, its unobstructed transmission distance is
3km.
3) The wireless connection of CPE206 wireless bridge is indicated by "Link", while the
CPE355 is indicated by "WLAN".
4.2 LED Indication & Function Chart:
WLAN
WLAN solid red light on indicates successful pairing, 4 grid green signal lights
indicate the signal strength (Only CPE 355)
Link
Pairing Indicator, Green LED Means Connected (Only CPE 206)
LAN1/LAN2
When the bridge data connection is successful, the LED light will turn on,
otherwise it will be off.
PWR
Power indicator, when the bridge connected to power source, the LED turns
on.
LED
Display
1, LED displays "H" indicates in manual configuration status, short press the
RST button to auto-configuration;
2, LED displays "L" and flashing indicates in auto-configuration status;
3, LED flashing indicates setting the configuration or connecting, solid light on
indicates that the pair is successful;
4, The digital LED indicator displays "o" and flashing means the "DIP switch
control" on the bridge control panel (UI) is disabled;
5, LED values represent the corresponding IP address and wireless channel.
A/B Switch
“A” position represents the master mode. “B” represents the slave mode.
POE/LAN
24V power supply and 100Mbps data transmission.
LAN
Only data transfer, 10/100Mbps RJ45 port.
Dot LED
When the device is on "B" mode, the light is on. When the device is on "A"
mode, the light is off.
RST
1, Short press the RST button to change the channel from 0,1,2,3...D in cycle
(E and F Reserved).
2, Long press RST button over 15 seconds, the system will return to factory
setting (only LED indicator displays "o" is valid).
4.3 LED Number match to IP & SSID & Channel Chart:
LED Value
(A)Master Mode
IP
(B)Slave Mode
IP
Channel
ID
WiFi SSID
Password
0
192.168.255.100
192.168.255.200
0
CPE5G_5G0
zllinkcpe1234560
1
192.168.255.101
192.168.255.201
165
CPE5G_5G165
zllinkcpe123456165
2
192.168.255.102
192.168.255.202
161
CPE5G_5G161
zllinkcpe123456161
3
192.168.255.103
192.168.255.203
157
CPE5G_5G157
zllinkcpe123456157
4
192.168.255.104
192.168.255.204
153
CPE5G_5G153
zllinkcpe123456153
5
192.168.255.105
192.168.255.205
149
CPE5G_5G149
zllinkcpe123456149
6
192.168.255.106
192.168.255.206
48
CPE5G_5G48
zllinkcpe12345648
7
192.168.255.107
192.168.255.207
44
CPE5G_5G44
zllinkcpe12345644
8
192.168.255.108
192.168.255.208
40
CPE5G_5G40
zllinkcpe12345640
9
192.168.255.109
192.168.255.209
36
CPE5G_5G36
zllinkcpe12345636
a
192.168.255.110
192.168.255.210
140
b
192.168.255.111
192.168.255.211
132
c
192.168.255.112
192.168.255.212
124
d
192.168.255.113
192.168.255.213
116
e(Reserved)
192.168.255.114
192.168.255.214
108
f(Reserved)
192.168.255.115
192.168.255.215
100
4.4 Auto-Configure Wireless Bridges
4.4.1 Connect Wireless Bridge Master to POE Adapter
4.4.2 Connect Wireless Bridge Slave to POE Adapter
4.4.3 Pairing the Master and Slave Mode
Pairing is simple enough by pressing the small button on the bottom of the unit then pressing
the button on the other unit within 60s. Please refer below:
a) Switch to “A” position, the device works on master mode, the Point LED is off;
b) Switch to “B” position, the device works on slave mode, the Point LED is on.
c) Connect the POE and plug the POE in AC power, wait patiently for them to power on,
about 2 minutes.
d) Short press the RST button to change the channel from "0" - "D", the LED indicator will
display the numeric to show what channel it is, please keep the master and slave both in the
same channel. The bridges will automatically complete the pairing.
Note: The bridges are pre-paired, just connect to POE adapter, it will auto pair in a few
minutes. If you want to change the channel, please short press RST to re-pair it.
Questo manuale è adatto per i seguenti modelli
1
Indice
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
