Sound ID 300 Manuale utente
Sound ID 300
Bluetooth™Headset
Quick Start Guide and User Manual
Please take a few moments to read this user manual.
It contains instructions for operating your Sound ID 300,
along with other important information.
For customer support please call 1-866-703-7480
To Achieve the Best Performance
with Your Sound ID 300 Headset:
• Place the phone in a belt holder or maintain a
line-of-sight. Holding the phone in your hand
reduces the wireless signals.
• Having the mobile phone on the opposite side
as your headset or behind you will reduce wireless
signals. Keep the mobile phone and headset on
the same side, preferably line-of-sight. If you
experience intermittent static, reposition the
phone to find the best reception.
DO DON’T
• As you increase the separation between your
phone and your headset the wireless signal
strength will be reduced and will produce static
and/or disconnect. Reduce the distance.
• If you put your phone in a purse or briefcase,
keep the purse or briefcase on the same side
as the headset.
Personal Sound Update
Sound ID has added a fourth Personal Sound mode that
turns the noise reduction off. To turn noise reduction off, hold
the Volume/Personal Sound button down for two seconds
to cycle through the modes until you hear four beeps. The
Personal Sound settings are as follows:
One beep: Normal listening enhancement.
Two beeps: Moderate listening enhancement.
Three beeps: Strong listening enhancement.
Four beeps: Noise reduction off.
Part #95006501
Welcome.
Thank you for purchasing the Sound ID 300 Headset.
Important Notices
The volume control should be set at a reasonable sound level. Prolonged
exposure to excessive volume over time can lead to hearing impairment.
If you suspect hearing problems, consult with your physician or an
audiologist.
The Sound ID 300 enables hands-free operation of mobile phones.
Please obey mobile phone laws while driving and pay full attention to the
operation of the vehicle.
Register Your Sound ID 300 Online
Visit www.soundid.com to register your product online so we can provide
you with the best possible service and support.
Questions & Support
For a Spanish version of this manual please visit www.soundid.com.
IMPORTANT INFORMATION PRIOR TO USE:
It is important to charge your Sound ID 300 battery for a minimum of four
hours before you use the headset for the first time. Subsequent charges
take up to 2.5 hours. When the headset is charging, the light is red.
When fully charged, it is green.
About Your Sound ID 300 Headset
BACK VIEW FRONT VIEW
RealComfort™
Ear Loop
Status Light
Main Button
Volume/
PersonalSound™
Program Button
(VPB)
Micro USB
Charging
Socket
Quick Start Guide
Microphone
Microphone
• Green - On and charged
(more than 30 min. remaining)
• Red - Powering off, or, Low
Battery
• Blinking Red-Green -
In pairing mode
• Blinking Green - Attempting
to connect with headset
1
To turn it ON: Press and hold the Main Button for approximately three
seconds. The status light will flash green when the headset is on.
To change the volume: Most handsets will allow you to change
the headset volume using the volume control on the phone. In this
case the Sound ID 300 remembers the new volume level.
The volume can also be changed on the headset. The headset has
four volume settings which can by cycled through by pressing the
Volume/PersonalSound™Program Button (VPB) briefly for each step.
You will hear a beep at the maximum volume step; upon the next press,
the volume goes back to lowest step.
To answer a phone call: Press the Main Button when the Sound ID
300 rings.
To end a phone call: Press the Main Button.
To make a phone call: Use the mobile phone to initiate the call. The
audio will automatically transfer to your Sound ID 300 headset.
To turn it OFF: Press and hold the Main Button for three seconds.
The status light will turn red when the headset turns off.
How It Works
2
You can customize your listening experience when on a call by choosing
one of three PersonalSound™levels. Use the Volume/PersonalSound™
Program Button to cycle through the three available enhancement levels.
To cycle to the next level, hold the button down for approximately two
seconds until you hear a corresponding beep (one, two, or three beeps
for normal, medium, or strong enhancement). Your headset is set to
“normal” by default.
There is a fourth setting, indicated by four beeps, that turns off
all sound enhancement and noise reduction. This setting can be used
to demonstrate the noise reduction capabilities of the Sound ID 300.
Choose a PersonalSound™Level
3
You must pair your headset with your mobile phone before it will work.
Consult your phone manual for pairing instructions for your specific
phone model. In general, here's how:
1. Turn OFF the headset if it is on. Turn ON the phone and navigate to
“Bluetooth Link”.
2. Press and hold down the Main Button on the Sound ID 300 for eight
seconds until the light flashes red and green. Note: the Sound ID 300
is automatically placed in pairing mode with the LED flashing red and
green each time it is powered on until successfully paired.
3. Select LOOK FOR DEVICES on the mobile phone, and then select
“Sound ID 300” when it appears on the menu screen.
4. If asked to pair, select YES.
5. If asked for a pin, passcode, or passkey, enter “0000”.
6. After successfully pairing, the Sound ID 300 status light will stop
flashing and the device will remain ON.
Pair Your Sound ID 300 with Your Bluetooth®Mobile Phone
4
5
Sound ID 300 Microphones are
Positioned Towards Mouth
Left Ear Fit
Rotate Tip to Line
Up With R
Rotate Tip to Line
Up With L
(Approximately 45 degrees)
Ear Tip
Hole
Holding the Sound ID 300 vertically, gently insert the eartip into your ear.
Ensure that the Ear Loop is securely tucked into the bowl of your ear and
rotate the Sound ID 300 until it points towards your mouth and fits snug-
gly in your ear. For the right ear, rotate the headset counterclockwise; for
the left ear, clockwise. Then, align the headset toward the mouth. You
may need to use a mirror to confirm the position for the first time.
Wearing Your Sound ID 300 Headset
For additional information about this device and its features, please refer
to the user manual section of this booklet or visit our website at
www.soundid.com.
Learn More
Sound ID 300 User Manual
Installing the RealComfort™Ear Loop
Three ear pieces are provided each with a different size RealComfort™
Ear Loop (large, medium, and small). The ear piece with the medium Ear
Loop comes pre-installed on the headset, so check its fit first. If it’s not
comfortable, try the other two to find the best fit. If you need to change
the ear piece, gently pull it away from the headset, then snap on the
desired ear piece and line the tip up with the left or right ear preference
(as shown on the Sound ID 300 below).
Large
Medium
(Installed on Device)
Small
6
Altri manuali per 300
1
Indice
Lingue:
Altri manuali Sound ID Cuffia
