Soundstream Stealth ST1.700D Manuale utente

UNDSTR

SERIES

ST1.700D

ST4.1000D

Thank you for your decision to purchase a

MICRO

MINI

mobile amplifier! Our

Amplifiers are

the

result

extensive engineering, testing,

and

bullet proof

construction. Their versatility enables compatibility with optional signal

and

audio processors. These high quality

MOSFET

amplifiers may

configured to

allow maximum flexibility in designing different types of speaker systems.

The

MICRO

MINI

Series are high quality

MOSFET

amplifiers

that

are capable

running a system full range,

they may be selected only to power subwoofers.

important

that

you closely follow the wiring instructions contained in this

Owners Manual so

that

you

get

the

most from

your

MICRO

MINI

mobile

amplifier.

High powered audio systems in a vehicle are capable of generating higher

then

"Live

Concert" levels

sound pressure. Continued exposure to excessively high

volume sound levels will cause hearing loss

damage. Also, operation

motor vehicle while listening to audio equipment

high volume levels may

impair

your

ability to

hear

external sounds such as horns, warning signals,

emergency vehicles -thus creating a potential traffic hazard.

In the interest of safety,

MICRO

MINI

highly recommends listening

lower

volume levels when driving.

• Class-D Digital Full range 2ohm stable stereo.

• Low-power Consumption Circuit.

•Tri-mode capable.

• Full

MOSFET

DC-DC

PWM

Power Supply.

• Four way protection.

• Double sided

FR-4

Board.

•

SMD

technology.

• High level input connector (Auto

turn

ON).

·Adjustable Low-pass, Hi-pass,

Bass

boost, Sub sonic filter.

•

RCA

input connectors

(No

Auto

tum

ON).

• Connector to connector Power/Speaker terminals.

• Ultra slim size.

Installation of

MICRO

MINI

mobile amplifiers requires detailed knowledge of

electronics wiring and proper speaker impedance.

strongly recommend installation

an authorized

our

dealer.

This Owners Manual only provides general installation

and

operation

instructions. If you have any reservations about your installation skills, please

contact your local

our

dealer for assistance.

PREPARING

FOR

INSTALLATION

NOTE: The tools listedbelow may

required

for

basic installation

• An

electric drill with bits

• Philips head

and

standard screwdrivers

·Wire

strippers

• Crimping tool

•

VOM

(electronic volt ohm meter)

• Heat shrink tubing and gun

• Soldering iron

INSTALLATION PRECAUTIONS

NOTE: Proceed only

you

are qualifiedinstaller otherwise, let

your

dealer

it.

Always wearprotective eyewear when using tools.

•

Tum

off

all stereo and other electrical devices before you begin.

• Disconnect the negative (-) lead from your vehicles battery.

• Locate all fuel lines, brake lines, oil lines, and electrical cables when planning the

install.

• Make sure there is at least 2-inches

em) around the air vents on the amplifier.

• When connecting ground points, make sure all paint is carefully scrapped away

from the auto body and contact is make with bare metal.

• Use a utility knife to trim away fabric from hole locations before drilling or cutting.

• When running power cables through sheet metal, be sure to use grommets to

properly insulate the metal edges from the wire insulation.

•

possible, use tubing through grommets.

MOUNTING

THE

AMPLIFIER

keep your

MICRO

MINI

amplifier running at top performance, choosing the

proper location it of utmost importance. For this reason the amplifier should

be mounted in a location which

will

allow air to circulate freely. A clearance

of at least 2-inches (5 em) to all sides of the amplifier

necessary not only for

proper cooling,

but

also for gaining access to the inputs and other variable

controls.

sure that the power and signal cable connections can enter and

leave the amplifier in a straight line to avoid the risk of kinked wires causing

a malfunction.

MOUNTING LOCATION

Your

MICRO

MINI

amplifier comes with mounting feet that need

be attached

the amplifier

prior to installation. Once the feet are in place, use the amplifier as a template and mark the

four screw locations. Use caution to make sure there are no objects behind the installation

surface that may become damaged during drilling.

The amplifier should be protected from exposure to moisture and direct sunlight. The best

places to mount your amplifier are: The floor

the trunk, under the driver's seat, or on the

back

the rear seat. For alternate installation locations, please consult your dealer.

• Upside

down

mounting

will

compromise

heat

dissipation

through

the

heatsink

and

could

engage

the

thermal

protection

circuit.

•

Try

avoid

mounting

the

amplifier

subwoofer

enclosure, as extended exposure

vibration

may

cause

malfunction

the

amplifier.

•

Don't

mount

the

amplifier

that

the

wire

connections

are unprotected

are

subject

pinching

damage

from

nearby objects.

• The

power

wire

must

be fused

the

battery

positive

(+)

terminal connection. Before

making

breaking

power

connections

the

amplifier

power

terminals,

disconnect

the

power

wire

the battery end.

• The

power

supply

the

car

audio

system

must

be disconnected

until

the entire

wiring

and

installation

completed.

ST4.1000D ST1.700D

[SPEAKERS

()lffl

(FUSE)

30A

lrl

Keep

using

6,8Pin

Connector

Keep

using

RCA

jack Connector

ST4.1000D

3 8

Keep

using

RCA

jackConnector

(SPEAKERS

OUT)

(FUSE)

l00l

l1:lli]

c±STC±J

~o:

30A

'14

Keep

using

6,8Pin

Connector

ST1.7000D

LINE

IN (RCA)

Jacks

The RCA style input jacks are for use with source units that have RCA line level

outputs. A source unit with a minimum

250mV is required for proper operation.

However, this input will accept levels up to 6Vrms.

High Level

Input

you are installing by using a high level. you do not need to connect

the remote

because.

hear a better sound quality, you must connect the high level ground wire

the head-unit

ground.

3. GAIN Control

This control is used to match the input sensitivity

the amplifier to the particular

source unit that you are using.

BASS BOOST Control

This equalization circuit is used to enhance the low frequency response

the vehicle's

interior. With up to 12dB

boost centered at 45Hz, the BASS EQ can be adjusted to

meet your own personal taste.

LPF

(Low Pass Filter Control)

This

control

continuously adjustable

from.

35Hz through 250Hz

per

octave.

X-OVER Switch for HI/FULL/LOW

Activates the built in electronic crossover network. Warks in conjunction with the HPF

and LPF adjustable controls.

HPF

(High Pass Filter) Control

This control is continuously adjustable from 35Hz through 250Hz at 12dB per octave

8. SUB Sonic Filter

Variable subsonic filter (20Hz

-50Hz)

The subsonic filter will roll offall

the unwanted frequencies below 20Hz -50Hz.

This will allow the amplifier to use that wasted power on the audible bandwidth.

POWER

Indicator

The GREEN when the power is on.

10.

SPEAKER

Terminals

As shown in the wiring diagrams, be sure to observe speaker polarity through the

system and speaker impedance. This specially tooled terminal is designed to

accommodate up to

gauge speaker wire.

11.GND

(Ground

Input

Connection)

A good quality ground

required for your

MICRO

MINI

amplifier

operate at peak

performance. A short length

cable the same gauge

your power cable should be

used to attache the ground terminal directly to the chassis

the vehicle.

12.

REMOTE

(Remote

Input

Connection)

All

MICRO

MINI

amplifiers can be turned on by applying

volts

this terminal. This can

be found on the rear

the source unit in the form

an electric antenna output, or a

remote output.

this is not available you can wire to the ACC position on the key. An

gauge wire is sufficient to run the REMOTE.

13.

+BATT

(Power

Input

Connection)

This terminal is the main power input for the amplifier and must be connected directly

to the positive (

+) terminal

the car battery. (see Power Cable Selection Chart on

Page 9 for recommended wire gauge for each model).

14.

FUSE

For convenience all

MICRO

MINI

amplifiers utilize common automotive ATC type fuses.

For continued protection in the event that a fuse blows, replace the fuse only with the

same value (see specifications page).

15.

REMOTE

BASS BOOST

CONTROL

This control adjusts the Bass Boost gain for the amplifier's speaker output

(0,..,

+18dB)

*Packed product can be different from the photograph.

REMOTE

@>)~

r·····l

12V

05V

....

.....

,..

,,..

- - -

L • G - R

45Hz

1111.0

tiPIIT

REMOTE

Remote control conections

ST1.7000D

Disconnect the negative (-) battery terminal before you start any wiring

work! The power supply of your car audio system must

disconnected

until the entire wiring installation

completed.

Your

MICRO

MINI

amplifier requires unrestricted current to deliver peak performance,

don't

"starve" your amplifier

using small power cable. Using too small

power cable can

result in unnecessary over-heating

the amplifier, distortion at high volume levels and

might even cause the thermal protection circuitry to shut-offthe amplifier.

• Use rubber grommets when running cables through any metal or sharp plastic, to

prevent accidental shorting

shearing. Make sure the cables do not interfere with

normal operation

the vehicle.

• The audio signal cables (RCA interconnects) should be kept far away from any

potential sources

electrical interference such as electronic vehicle management

systems (relays, engine computers etc.) wiring harnesses, fuel pumps etc.

Altri manuali per Stealth ST1.700D

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Soundstream Amplificatore

Soundstream

Soundstream XXX-15000D Manuale utente

Soundstream

Soundstream Granite 110.2 Manuale utente

Soundstream

Soundstream Picasso Manuale di servizio

Soundstream

Soundstream Picasso PCA2.130 Manuale di programmazione

Soundstream

Soundstream ST4.1000DB Manuale utente

Soundstream

Soundstream RUBICON 1002 Manuale di programmazione

Soundstream

Soundstream Picasso Nano P4.320D Manuale utente

Soundstream

Soundstream P203 Manuale di programmazione

Soundstream

Soundstream CLASS-A-10.0 Manuale utente

Soundstream

Soundstream Reference Series 200 Manuale di programmazione

Soundstream

Soundstream D-Tower Amplifier Series Manuale utente

Soundstream

Soundstream TRX10000 Manuale utente

Soundstream

Soundstream Reference 705s Manuale di programmazione

Soundstream

Soundstream SA.120 Manuale di programmazione

Soundstream

Soundstream USA 305 Manuale di programmazione

Soundstream

Soundstream STEALTH Series Manuale utente

Soundstream

Soundstream Tarantula Amplifier Series Manuale utente

Soundstream

Soundstream Lilwonder III Generation LW4.620 Manuale di programmazione

Soundstream

Soundstream Tarantula Amplifier Series Manuale utente

Soundstream

Soundstream Reference 414s Manuale di programmazione

Soundstream

Soundstream Tarantula Amplifier Series Manuale di programmazione

Soundstream

Soundstream Reference Series CLASS-A-3.0 Manuale utente

Soundstream

Soundstream REFERENCE 300SX Manuale di programmazione

Soundstream

Soundstream Rubicon 1000D Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente