Spartan 1272 Manuale utente

PROGRAMMABL MOTORIZED TREADMILITEM
NO: 1272

OWNER’S MANUAL
IMPORTANT: Read all instructions carefully before using this product. Retain this
owner’s anual for future reference.
The specifications of this product ay vary fro this photo, subject to change without
notice.
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS ------------------------------------------- 2
PARTS LIST -------------------------------------------------------------------------------- 4
HARDWARE PACKING LIST ---------------------------------------------------------- 5
SILICONE OIL INCLUDED ------------------------------------------------------------- 6
TOOLS -------------------------------------------------------------------------------------- 6
OVERVIEW DRAWING ----------------------------------------------------------------- 7
ASSEMBLY INSTRUCTIONS --------------------------------------------------------- 8
STORAGE ---------------------------------------------------------------------------------- 11
OPERATING THE COMPUTER ------------------------------------------------------ 12
CARE MAINTENANCE & TROUBLESHOOTING GUIDE -------------------- 24
BELT ADJUSTMENT AND LUBRICATION ---------------------------------------- 25
WARM UP AND COOL DOWN ROUTINE ----------------------------------------- 26

MPORTANT SAFETY INSTRUCTIONS
Basic precautions should al ays be follo ed, including the follo ing safety
instructions hen using this treadmill: Read all instructions before using this
treadmill.
DANGER: To reduce the risk of electric shock please read the following:
Always unplug the treadmill from the electrical outlet immediately after using and
before cleaning assembling or servicing.
NOTE: Failure to follo these instructions may lead to personal injury and cause
damage to the treadmill.
WARNING: To reduce the risk of burns fire electric shock or injury to any persons please
read the following:
Never leave the treadmill unattended when plugged in. Disconnect by turning off the
master power switch and unplugging from outlet when not in use and before putting
on or taking off parts.
Use this appliance only for its intended use as described in this manual. Do not use
attachments not recommended by the manufacturer.
Never operate this treadmill if it has a damaged cord or plug or if it is not working
properly. If it has been dropped or damaged or been exposed to water return the
appliance to a service center for examination and repair.
Do not attempt any maintenance or adjustments other than those described in this
manual. Should any problems arise discontinue use and consult an Authorized
Service Representative.
Never operate the appliance with the air openings blocked. Keep the air openings
free of lint hair and the like.
Do not use the treadmill outdoors.
Do not pull the treadmill by its power cord or use the cord as a handle.
Keep children and pets away from the equipment while in use. This machine is
designed for adults only. Close supervision is necessary when this treadmill is used
by on near invalids or disabled persons.
Do not operate where aerosol (spray) products are being used or where oxygen is
being administered.
Keep Dry - do not operate in a wet or moist condition. Save these instructions.
Do not operate the treadmill near a blanket. Excessive heating can occur and cause
fire electrical shock or injury to user.
Keep electrical cord away from heated surfaces.
Never insert any object into any opening.
Keep the treadmill on a solid level surface with the minimum safety area clearance of
2000mm x 1000mm of the treadmill. Be sure the area around the treadmill remains
clear during use and has adequate clearance.
This treadmill is for household use only.
Only one person should be on the treadmill while in use.
Wear comfortable and suitable clothing when using the treadmill. Do not use the
treadmill barefoot in only socks or in sandals always wear athletic shoes. Never
wear loose clothing because it could run the risk of getting caught in the treadmill.
Always hold on to the handrails while using the treadmill.
Always make sure the storage latch is in place when folding and moving the treadmill.
Do not leave children who are under 12 year-old unsupervised near or on the
treadmill.

To disconnect turn all controls to the off position then remove plug from outlet.
This appliance is not intended for use by persons (including children) with reduced
physical sensory or mental capabilities or lack of experience and knowledge unless
they have been given supervision or instruction concerning use of the appliance by a
person responsible for their safety. Children should be supervised to ensure that they
do not play with the appliance.
If the supply cord is damaged it must be replaced by the manufacture its service
agent or similarly qualified persons in order to avoid a hazard.
Pull up the Safety Tether Key for emergency stop. Reinstall the Safety Tether Key
onto the Computer Console. Press the START button to begin exercise again.
Maximum Weight Capacity for this product is 125 kgs.
Note: It is the obligation of the o ner to revie and explain these safety precautions
to all users of this treadmill.
WARNING: Connect the treadmill to a properly grounded outlet only. See grounding
instructions.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This product must be grounded. If it should malfunction or break down grounding
provides a path of least resistance for electric current reducing the risk of electric
shock. * This treadmill is equipped ith a cord having equipment grounding
conductor and a grounding plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in accordance ith all local codes
and ordinances.
DANGER: Improper connection of the treadmill grounding conductor can result in the risk
of electric shock. Check with a qualified electrician if you are in doubt as to whether the
product is properly grounded. Do not modify the plug provided with the treadmill. If it will
not fit your outlet have a properly grounded outlet installed by a qualified electrician.
Make sure that the product is connected to an outlet having the same configuration as the
plug.
This unit must be plugged into a nominal 220-240 volt 50/60 HZ which has a
grounding.
Keep hands clear of all moving parts. Never place hands feet under the treadmill.
Do not use the treadmill on a carpet that is greater than 1/2 inch in height.
Before using the treadmill check that the belt is aligned and centered on the walking
deck and all visible fasteners on the treadmill are sufficiently tightened and secure.
WARNING: Before beginning any exercise program consult your physician. This is
especially important for the persons who are over 35 years old or who have
pre-existing health problems. Read all instructions before using any fitness equipment.
We assume no responsibility for personal injury or property damage sustained by or
through the use of this product. Do not operate this exercise equipment without properly
fitted guards as the moving parts can present a risk of serious injury to young children.
CAUTION: Read all instructions carefully before operating this product. Retain
this Owner’s Manual for future reference.

Part
#ln, Description Qty Part # Description Qty
001 Base Frame 1 034 Rear Roller Cover 1
002 Main Frame 1 035 Motor Cover 1
003 Incline Frame 1 036 Side Rail 2
004 Left Handlebar Support 1 037 Upper Supporting Tube 1
005 Right Handlebar Support 1 038 Upper Supporting Tube Cap 1
006 Computer Bracket 1 039 Lower Supporting Tube Cap 1
007 Left Handrail 1 040 Lower Supporting Tube 1
008 Right Handrail 1 041 Foot Lock Latch 1
009 Pulse Pulse Sensor Bar 1 042 Sensor Wire I (2000mm) 1
010 Incline Motor 1 043 Sensor Wire II (500mm) 1
011 Gas Spring 1 044 Hand Pulse Sensor Wire
(800mm)
2
012 Motor Bracket 1 045 Control Wire (1200mm) 2
013 Motor 1 046 Spring 1
014 Front Roller 1 047 Washer 8
015 Rear Roller 1 048 Flat Head Screw M4x15 8
016 Running Deck
1 049 Lower Computer Cover 1
017 Running Belt 1 050 Computer
018 Transformer 1 050A Computer Panel Sticker 1
1 Set
019 Flat Head Screw M3x8 1 050B Computer Panel 1
020 Power Control Board 1 050C Upper Computer Cover 1
021 Power Switch 1 050D Computer Power
Control Board
1
022 Fuse 1 050E Control Button 16
023 Motor Sensor Wire (1100mm) 1 050F START Button 1
024 Rubber Wheel Ø53xØ8.5x23 2 050G STOP Button 1
025 Transport Wheel Ø61.5xØ8.5x23 2 050H ENTER Button 1

Part
#.... Description Qty Part # Description Qty
052 Hand Pulse Sensor 2 Sets 068 Bolt M8x22 5
053 Screw M3x30 4 069 Flat Washer
Ø10.5xØ23xT1.5
4
054 Screw M4x55 4 070 Flat Head Bolt M8x32
8
055 Bolt M8x45
1 071 Screw M4x10 2
056 Bolt M8x65
2 072 Bolt M8x30 2
057 Instant Incline Button with
Cover
1 073 Bolt M8x42 5
058 Instant Speed Button with
Cover
1 074 Flat Washer Ø8.4xØ20xT1.5 23
059 Foam Grip 4 075 M8 Lock Nut 12
060 Power Cord 1 076 Bolt M10x42
1
061 Red Wire I (100mm) 1 077 Bolt M10x65 1
062 Red Wire II (150mm) 1 078 M10 Lock Nut 2
063 Green Wire (150mm) 1 079 Bolt M8x15
30
064 Earth Wire (Green+Yellow) 1 080 Spring Washer (8mm) 2
065 Screw M4x12
10 081 Clock Washer (8mm) 23
066 Screw M4x15 40 082 Bolt M8x100
1
067 Bolt M8x70
1 083 Bolt M4x8
4

HARDWARE PACKING LIST
SILICONE OIL INCLUDED
SILIKONOVÝ OLEJ
TOOLS
NÁŘADÍ
Silicone Oil
1 PC
Silikonový
olej
(79) Bolt M8x15
16 PCS
šroub
(66) Screw M4x15
4 PCS
šroub
(51) Safety Tether Key
1 PC
Bezpečnostní klíč
(81) Clock Washer (8mm)
16 PCS
Ozubená podložka
Allen Wrench
1 PC
Univerzálny
klíč
Phillips Screwdriver
1 PC
Philips šroubovák

OVERVIEW DRAWING


ASSEMBLY INSTRUCTIONS
Step 1
Slide the Right Base Cover (30) up onto Right Handlebar Support (05). Insert the Sensor
Wire I (42) through into the bottom hole of Right Handlebar Support (05) and pull it out
from the top hole of Right Handlebar Support (05). Then install the Right Handlebar
Support (05) to the Base Frame (01) by inserting the Right Handlebar Support (05) onto
the Base Frame (01) using five M8x15 Bolts (79) and five 8mm Clock Washers (81).
Tighten bolts with the Allen Wrench Provided. Slide the Right Base Cover (30) down onto
the Base Frame (01).
Slide the Left Base Cover (29) up onto Left Handlebar Support (04). Then install the Left
Handlebar Support (04) to the Base Frame (01) by inserting the Left Handlebar Support
(04) onto the Base Frame (01) using five M8x15 Bolts (79) and five 8mm Clock Washers
(81). Tighten bolts with the Allen Wrench Provided. Slide the Left Base Cover (29) down
onto the Base Frame (01).
NOTE: Do not fully tighten hardware in step 1 until step 2 is completed.
Hard are:
Allen Wrench
Tool:
Indice
Altri manuali Spartan Tapis roulant


















