Spartz MULTISCALE Manuale utente

MULTISCALE

1080p Scaler Box

Operation Manual

TABLE OF CONTENTS

1. Introduction.............................................................................. 1

2. Features...................................................................................... 1

3.PackageContents..................................................................…..1

4. Operation Controls and Functions .......................................2

4.1 Front Panel...............................................................………....2

4.2 Rear Panel...................................................................……......2

4.3 OSD Operation........................................................................4

4.4 Remote Control........................................................................5

5. MULTISCALE RS-232 Remote Control Protocol................6

6. Specifications.............................................................................9

6.1 General Specification...............................................................9

6.2 Support Resolution............................................................…..9

7. Connection and Installation..................................................10

Introduction

SPATZ's Multiscale Scaler Box

is designed to upscale digital/analog video signal from

Composite, S-Video, PC, Component (HD) and HDMI input sources, to digital HDMI output of

wide-range HDTV and PC resolutions, up to 1080p and WUXGA (1920 x 1200.) Besides video

upscaling, the scaler box also converts digital/analog audio signal to digital format, then output

either through HDMI combining with the video, or Coaxial S/PDIF separately. SPATZ Multiscale

has a comprehensive OSD menu that allows user to select a variety of output resolutions and

adjust for best picture quality.

2. Features

1. HDMI 1.2, HDCP 1.1 and DVI 1.0 compliant.

2. Scales any PC (VGA ~ WUXGA) /HD (480i ~ 1080p) resolutions to/from

another PC/HD resolutions.

3. Automatically detect the factory setting of the connected display and

output the corresponding resolution and refresh rate, when the NATIVE

output is selected.

4. Supports 50/60Hz frame rate conversion.

5. Supports 3-D motion video adaptive, 3-D de-interlacing, and 3:2 / 2:2 pull-

down detection and recovery.

6. Provides output picture adjustment on contrast, brightness, hue, saturation,

sharpness, RGB (color tone) level, and aspect ratio size.

7. Supports high resolution input/output:

PC: VGA, SVGA, XGA, SXGA, UXGA, WXGA, WSXGA, WUXGA

HDTV: 480i, 576i, 480p, 576p, 720p, 1080i, and 1080p

8. Supports digital and analog audio input and output.

9. Automatic input selection for HDMI and VGA, VGA has priority. Unit defaults to HDMI if not

VGA signal is connected.

10. SPATZ AUTOSCALE

Since 01.11.2011 we offer a new firmware with the unit that incorporates our AUTO

SCALE. This function allows automatic scaling of any input signal maintaining original

aspect ratio by scaling the input format to the selected output format using either full

display height or full display witdth. No more image distortion with egg shaped

circles. As an example the unit will accept a XGA input image (4:3)and display it

centered on a 1080p (16:9) output image with correct aspect ratio. The scaler will scale

768 lines to 1080p and increase the horizontal pixels by the same ratio and filling left and

right side with black bars to complete the 1920 pixels.

3. Package Contents

1. SPATZ Multiscale Scaler Box

2. D-Sub (15pin) Cable

3. 3XRCA Cable (Composite Video + L/R Audio)

4. Remote Controller

5. 5VDC Power Supply Adaptor

6. Operation Manual

4. Operation Controls and Functions

4.1 Front Panel

1. POWER Button and LED Indicator:

Press the button to turn ON/OFF the power of the unit. The LED will illuminate when the

power is turned on.

2. IR remote control sensor.

3. Input Selection Buttons and LED Indicators:

Press each of the buttons (CV/SV/COMP/PC/HDMI) to select the desired input source. The

LED will illuminate when the corresponding input is selected.

4. MENU Button:

Press the MENU button to bring up OSD operation menu (see section “4.3 OSD Operation”

for reference.)

5. +/- Buttons:

a. On the first tier of OSD menu, use + and - buttons to move up/down

the highlight item for selection.

b. Once the desired option is selected, use + and - buttons to toggle

between setting values.

6. ENTER Button:

In OSD menu, use the ENTER button to confirm the selection.

4.2. Rear Panel

1. HDMI OUT and CO-AX OUT:

Connect the HDMI OUT port to the HDMI input port of your display such as HDTV. Connect

the CO-AX OUT port to the Coaxial (S/PDIF) input port of your amplifier for separate digital

audio output.

2. AUX IN Input:

When the video signal input through the HDMI IN port is from a DVI source such as a PC,

use the AUX IN port to input the audio signal.

3. HDMI IN Input:

Connect the HDMI IN port to the HDMI output port of your source equipment such as DVD

player or Set-Top-Box. Or, use HDMI to DVI cable to connect to the DVI output of your PC.

4. RS-232: Remote Control Port, for AMX or Crestron contol systems

5. PC IN for Video and Audio Input:

Connect the PC IN D-Sub (15-pin) port to the D-Sub output port of your PC. And, connect

the PC IN 3.5mm phone jack to the audio output port of your PC.

6. Y Pb/Cb Pr/Cr Video and L/R Audio Input:

Connect the Y Pb/Cb Pr/Cr (Component) 3 RCA input ports to the Component output port of

your video source equipment such as DVD player or Set-Top-Box. And, connect the L/R

audio input ports to the audio output port of your audio source equipment.

7. CO-AX Input:

The CO-AX port provides the digital audio input support, and can be used to combine with

each video input signals from CV/SV/COMP/PC/HDMI ports. Once connected, please use the

Audio Source Selection in the OSD menu to select between Coaxial (S/PDIF) or other audio

source (see section “4.3 OSD Operation” for reference.)

8. Composite Video / S-Video and L/R Audio Input:

Connect the Composite or S-Video input port to the Composite or S-Video output port of

your video source equipment such as DVD player or Set-Top-Box. And, connect the L/R

audio input ports to the audio output port of your audio source equipment.

9. Power:

Plug the 5VDC power supply into the unit and connect the adaptor to AC wall outlet.

4.3. OSD Operation

1st Tier Option

2nd Tier

Option

Adjustment

VIDEO

- PICTURE

MODE

USER / STANDARD / VIVID / MOVIE

- CONTRAST

0 ~ 100 of Contrast Level

- BRIGHTNESS

0 ~ 100 of Brightness Level

- HUE

0 ~ 100 of Hue Level

- SATURATION

0 ~ 100 of Saturation Level

- SHARPNESS

0 ~ 100 of Sharpness Level

- SCALE

OVERSCAN / UNDERSCAN /

LETTERBOX / PANSCAN / FULL

- NR

LOW / MIDDLE / HIGH / OFF

- EXIT

Back to the 1st Tier

COLOR

- COLOR

TONE

USER / NORMAL / WARM / COOL

- RED

0 ~ 100 of Red Color Level

- GREEN

0 ~ 100 of Green Color Level

- BLUE

0 ~ 100 of Blue Color Level

- EXIT

Back to the 1st Tier

OUTPUT

NATIVE / VGA / SVGA / XGA / SXGA /UXGA / 480i / 480p /

720p@60Hz / 1080i@30Hz / 1080p@60Hz / 576i / 576p /

720p@50Hz / 1080i@25Hz / 1080p@50Hz / WXGA / WSXGA

/ WUXGA

OSD

- HPOSITION

0 ~ 100 of OSD Horizontal Position

- VPOSITION

0 ~ 100 of OSD Vertical Position

- TIMER

0 ~ 100 of OSD Show Time (sec.)

- TRANSP

0 ~ 100 of OSD Transparent Level

- EXIT

Back to the 1st Tier

AUDIO

- SOURCE

HDMI / L/R / COAXIAL

- DELAY

OFF / 40MS / 110MS / 150 MS

- SOUND

ON / MUTE

- EXIT

Back to the 1st Tier

INFORMATION

SOURCE (Input interface)

INPUT (Input Resolution)

OUTPUT (Output Resolution)

VERSION (Firmware Version)

EXIT

Close the OSD Menu

4.4. Remote Control

1. POWER:

Press the button once to power on the Multiscale

Press again

to enter standby mode.

2. INPUT:

Press the button repeatedly to toggle through

various input sources.

3. HD Input:

Press the button to directly select component input.

4. PC Input:

Press the button to directly select PC input.

5. HDMI/DVI Input:

Press the button to directly select DVI (or HDMI) input.

6. Output Resolution:

Press any one of the button to directly select output

resolution. For other output resolutions that are not covered

by these buttons please enter OSD Menu to select them.

7. MENU:

Press the button to bring up OSD main menu page.

8. Exit:

Press the button to exit from a sub menu or main menu.

9. Up/Down/Left/Right:

Press the Up/Down button to move the highlight bar to your desired parameter during the

OSD operation. Press the Left/Right button to increase/decrease the setting value of a

selected parameter.

10. OK (Enter):

Press the button to confirm your selection.

11. Reset:

Press the button to reset the unit's firmware setting to the factory default value.

12. Auto Adjust:

Press the button to optimize the position of the picture (picture centering) on the screen.

5. Specifications

5.1. General Speciﬁcation

* Frequency bandwidth: 1.65Gbps (single link)

* Input Ports:

Composite x 1 / L/R x 1

S-Video x 1 / L/R x 1

Component (3 RCA) x 1 / L/R x 1

PC D-Sub (15-pin) x 1 / 3.5mm Phone Jack x 1

HDMI x 1 / 3.5mm Phone Jack x 1 (for DVI) Coaxial (S/PDIF) x 1

* Output Ports: HDMI x 1

Coaxial (S/PDIF) x 1

* 5V DC power supply

Dimensions: 215(W) x 154(D) x 47(H)mm*

Weight: 1K

Pin deﬁnition for serial cable

Multiscale

Remote Controller

Deﬁnition

TxD

RxD

GND

RS-232 transmission format:

BaudRate: 19200 bps

Data Bit: 8 bits Parity: None

Stop Bit: 1 bit

Serial Commands:

Command Code

Response

Description

S POWER 0

> POWER OFF

POWER OFF

S POWER 1

> POWER ON

POWER ON

S SOURCE 0

> SOURCE CV

CV INPUT

S SOURCE 1

> SOURCE SV

SV INPUT

S SOURCE 2

> SOURCE COMP

COMP INPUT

S SOURCE 3

> SOURCE PC

PC INPUT

S SOURCE 4

> SOURCE HDMI

HDMI INPUT

S OUTPUT 0

> OUTPUT NATIVE

NATIVE RESOLUTION OUTPUT

S OUTPUT 1

> OUTPUT VGA

VGA RESOLUTION OUTPUT

S OUTPUT 2

> OUTPUT SVGA

SVGA RESOLUTION OUTPUT

S OUTPUT 3

> OUTPUT XGA

XGA RESOLUTION OUTPUT

S OUTPUT 4

> OUTPUT SXGA

SXGA RESOLUTION OUTPUT

S OUTPUT 5

> OUTPUT UXGA

UXGA RESOLUTION OUTPUT

S OUTPUT 6

> OUTPUT 480I

480I RESOLUTION OUTPUT

S OUTPUT 7

> OUTPUT 480P

480P RESOLUTION OUTPUT

S OUTPUT 8

> OUTPUT 720P

720P 60HZ RESOLUTION OUTPUT

S OUTPUT 9

> OUTPUT 1080I

1080I 60HZ RESOLUTION OUTPUT

S OUTPUT 10

> OUTPUT 1080P

1080P 60HZ RESOLUTION OUTPUT

S OUTPUT 11

> OUTPUT 576I

576I 60HZ RESOLUTION OUTPUT

S OUTPUT 12

> OUTPUT 576P

576P 60HZ RESOLUTION OUTPUT

S OUTPUT 13

> OUTPUT 720P

720P 50HZ RESOLUTION OUTPUT

S OUTPUT 14

> OUTPUT 1080I50

1080I 50HZ RESOLUTION OUTPUT

S OUTPUT 15

> OUTPUT 1080P50

1080P 50HZ RESOLUTION OUTPUT

S OUTPUT 16

> OUTPUT WXGA

WXGA RESOLUTION OUTPUT

S OUTPUT 17

> OUTPUT WSXGA

WSXGA RESOLUTION OUTPUT

S OUTPUT 18

> OUTPUT WUXGA

WUXGA RESOLUTION OUTPUT

S SIZE 0

> SIZE

FULL

SCALER FULL OUTPUT

S SIZE 1

> SIZE OVERSCAN

SCALER OVERSCAN OUTPUT

S SIZE 2

> SIZE UNDERSCAN

SCALER UNDERSCAN OUTPUT

S SIZE 3

> SIZE LETTERBOX

SCALER LETTERBOX OUTPUT

S SIZE 4

> SIZE PANSCAN

SCALER PANSCAN OUTPUT

S SIZE 5

SIZE FOLLOW INPUT

OUTPUT IMAGE FOLLOWS INPUT

S PICTUREMODE 0~3

> PICTUREMODE

STANDARD~USER

0:STANDARD; 1:MOVIE; 2:VIVID;

3:USER, PICTURE MODE OUTPUT

S CONTRAST 0~100

> CONTRAST 0~100

CONTRAST 0~100 ADJUST [Defaut:50]

S BRIGHTNESS 0~100

> BRIGHTNESS 0~100

BRIGHTNESS 0~100 ADJUST

[Defaut:45]

S HUE 0~100

> HUE 0~100

HUE 0~100 ADJUST [Defaut:50]

S SATURATION 0~100

> SATURATION 0~100

SATURATION 0~100 ADJUST

[Defaut:60]

S SHARPNESS 0~100

> SHARPNESS 0~100

SHARPNESS 0~100 ADJUST

[Defaut:32]

S NR 0~3

> NR OFF~HIGH

0:OFF; 1:LOW; 2:MIDDLE; 3:HIGH, NR

CONTROL

S PCHPOSITION 0~100

> PCHPOSITION

0~100

H POSITION 0~100 ADJUST

S PCVPOSITION 0~100

> PCVPOSITION

0~100

V POSITION 0~100 ADJUST

S PCCLOCK 0~100

> PCCLOCK 0~100

PC MODE COLCK 0~100 ADJUST

S PCPHASE 0~63

> PCPHASE 0~63

PC MODE PHASE 0~63 ADJUST

S COLORTEMP 0~3

> COLORTEMP

NORMAL~USER

0:NORMAL; 1:WARM; 2:COOL;

3:USER, COLOR TEMP SETTING

S RED 0~100

> RED 0~100

COLOR TEMP "RED" ADJUST

[Defaut:47]

S GREEN 0~100

> GREEN 0~100

COLOR TEMP "GREEN" ADJUST

[Defaut:47]

S BLUE 0~100

> BLUE 0~100

COLOR TEMP "BLUE" ADJUST

[Defaut:47]

S OSDHPOSITION 0~100

> OSDHPOSITION

0~100

OSD H POSITION 0~100 ADJUST

[Defaut:50]

S OSDVPOSITION 0~100

> OSDVPOSITION

0~100

OSD V POSITION 0~100 ADJUST

[Defaut:50]

S OSDTIMEOUT 0~100

> OSDTIMEOUT

0~100

OSD TIMEOUT 0~100 SETTING

[Defaut:10]

S OSDBACKGROUND 0~8

> OSDBACKGROUND

0~8

OSD OSDBACKGROUND 0~8 ADJUST

[Defaut:5]

S AUDIOMUTE 0~1

> AUDIOMUTE

OFF~ON

0:OFF; 1:ON, AUDIO MUTE CONTROL

S AUDIODELAY 0~3

> AUDIODELAY

OFF~150MS

0:OFF; 1:40MS; 2:110MS; 3:150MS,

AUDIO DELAY SETTING

S RESET 1

> RESET

RESET ACTION

Indice

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente