Speck pumpen V 30 Manuale utente
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
Assembly Instructions
V 30 – 430
Assembly Instructions V 30 - 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
2
Contents
1DISMANTLING PUMP......................................................................................... 3
1.1
Disassembling Inter Casing from Pump Casing .................................................................... 3
1.1.1
Type V 95/ V 130/ V 155 / V 330/ V 430 ............................................................................. 3
1.1.2
Type V 255 .......................................................................................................................... 3
1.2
Disassembling Impeller ............................................................................................................ 4
1.3
Disassembling Shaft Seal Housing ......................................................................................... 4
1.4
Disassembling Mechanical Seal .............................................................................................. 4
2REASSEMBLING PUMP..................................................................................... 5
2.1
Reassembling Mechanical Seal ............................................................................................... 5
2.1.1
Rotating part of Mechanical Seal......................................................................................... 5
2.1.2
Standstill part of Mechanical Seal ....................................................................................... 5
2.2
Reassembling Shaft Seal Housing .......................................................................................... 6
2.3
Reassembling and Adjusting Impeller .................................................................................... 7
2.4
Reassembling Inter Casing ...................................................................................................... 7
2.5
Reassembling Pump Case and Shaft Seal Housing .............................................................. 8
2.6
Reassembling Pump Case and Inter Casing .......................................................................... 8
2.7
Reassembling Pump Case and Shaft Seal Housing .............................................................. 8
Assembly Instructions V 30 - 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
3
General Remarks
Before disassembly the pump, isolate the electrical input and disconnect the operation liquid connec-
tion, and inlet and outlet connections. Disassemble and reassemble the pump on a level surface. Mark
all parts as they become accessible during disassembly to ensure correct positioning for reassembly.
Before starting disassembly, collect the parts, materials and standard tools, which are required for
disassembly and reassembly of the pump
.
Special Tools, Parts and Materials
Feeler gauge
Molykote G-n Paste or equivalent
Liquid sealing e.g. Epple 32
Metal straightedge
Loctite 242 and Primer
Solvent such as kerosene
1
Dismantling Pump
•Remove five fixed pump casing screws (901)
•Remove pump casing (101)
•Remove inter casing (137)
1.1
Disassembling Inter Casing from Pump Casing
1.1.1 Type V 95/ V 130/ V 155 / V 330/ V 430
•Remove fixed hexagon socket countersunk head screw (901.2) at inter casing (137)
•Remove inter casing (137) from pump casing (101)
1.1.2 Type V 255
•Remove fixed screwed plug (903) at pump casing (101)
•Remove fixed hexagon socket head cap screw (914) at pump casing (101)
•Turn around pump casing (101) and inter casing (137)
•Remove inter casing (137)
Assembly Instructions V 30 - 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
4
1.2
Disassembling Impeller
•Block the impeller (230) at shaft seal housing (441)
•Remove fixed hexagon nut from impeller adjusting screw
•Remove impeller (230) from shaft
•Remove impeller screw (906) and distance springs (950) from shaft. Notice position of distance
springs
1.3
Disassembling Shaft Seal Housing
•Remove fixed hexagon nut or hexagon head cap screw at motor flange
•Remove shaft seal housing from motor flange
1.4
Disassembling Mechanical Seal
•Turn around shaft seal housing
•Press mechanical seal out of seat at shaft seal housing (back side)
•Remove rotating part of mechanical seal at impeller
Assembly Instructions V 30 - 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
5
2
Reassembling Pump
(e.g. V 55)
CAUTION
Thoroughly clean all parts before reassembly, be sure to remove all old gasket mate-
rial from mounting flanges. Remove burrs from mating surfaces and mounting faces.
Remove rust at seat for mchanical seal.
2.1
Reassembling Mechanical Seal
2.1.1 Rotating part of Mechanical Seal
Coat the O-ring of mechanical seal with thin-bodied oil
Move mechanical seal (047) over the shaft of impeller (230). Don‘t touch the surface of the mechanical
seal. Coat the bore of impeller with molykote
2.1.2 Standstill part of Mechanical Seal
Coat the O-ring of mechanical seal with thin-bodied oil
Install mechanical seal (047) at shaft seal housing (441). Don‘t touch the surface of the mechanical
seal
Assembly Instructions V 30 - 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
6
2.2
Reassembling Shaft Seal Housing
Set motor on air ventilation cap
Install distance springs (950, with molykote coated) on the impeller adjusting screw (906). Be carefull
because the distance springs should be mounted as shown in the picture above. Coat the thread of
impeller adjusting screw also with molykote
Tread in the impeller adjusting screw into the motor shaft
Align the studs of the motor flange with the holes of the shaft seal housing (441)
Install four washers on the studs of the motor flange
Thread on four nuts on the studs of the motor flange and tighten nuts.
Assembly Instructions V 30 - 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
7
2.3
Reassembling and Adjusting Impeller
Install impeller on motor shaft
Coat the disk of impeller with liquid seal (Epple)
Install washer on the coated disk of impeller
Thread on nut to impeller adjusting screw
Adjust impeller with the impeller adjusting screw. There should be a gap of 0.1 – 0.15 mm between the
surface of the impeller and the surface of the shaft seal housing. Use the metal straightedge and the
feeler gauge to adjust the gap.
Block the impeller if the gap is correct. Tighten nut of the impeller screw.
Turn impeller. There should be no contact between impeller and shaft seal housing and also no con-
tact between impeller and metal straightedge. If there is any contact re-adjust the impeller.
2.4
Reassembling Inter Casing
Coat shaft seal housing (411) with liquid seal (Epple)
Install inter casing on shaft seal housing. Correct position of inter casing is given through the pins at
shaft seal housing
Assembly Instructions V 30 - 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
8
2.5
Reassembling Pump Case and Shaft Seal Housing
Coat pump casing (101) with liquid seal (Epple)
Install pump case (101) on inter casing (137). Thread in five hexagon head screws (901). Tighten the
screws (901) cross-wise.
Thread in all disassembled hexagon socket screwed plugs with their gaskets.
2.6
Reassembling Pump Case and Inter Casing
Type V 95 / 130 / 155 / 255 / 330 / 430
Install O-Ring (412) at pump casing
Install inter casing at pump casing. Correct position is given through the pin of pump case
Apply Loctite to thread and thread in hexagon socket countersunk head screw (901.2) and tighten
screw (screw 914 at V 255 / screw 904 at V 330-430).
2.7
Reassembling Pump Case and Shaft Seal Housing
Type V 95 - 430
Install O-ring (412) at shaft seal housing
Install pump case (101) on shaft seal housing (441)
Thread in five hexagon head screws (901)
Tighten the screws (901) cross-wise
Assembly Instructions V 30 - 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
9
3)
2)
412
561.1
746
598
901.3
550.1
901
047 Gleitringdichtung mechanical seal
101 Pumpengehuse pump casing
137 Steuerscheibe inter casing
230 Laufrad impeller
411 Dichtring joint ring
411.1 Dichtring joint ring
412 O-Ring o-ring
441 Gehuse f¤r Wellendichtung shaft seal housing
524 Wellenschutzh¤lse shaft protection sleeve
550 Scheibe disk
550.1 Scheibe disk
550.2 Scheibe disk
550.3 Scheibe disk
561 Kerbstift grooved pin
561.1 Kerbstift grooved pin
598 Blech sheet
746 Klappe flap
800 Motor motor
900 Schraube screw
901 6kt Schraube hexagon head cap screw
901.1 6kt Schraube hexagon head cap screw
901.2 6kt Schraube hexagon head cap screw
901.3 6kt Schraube hexagon head cap screw
903 Verschlussschraube screwed plug
903.1 Verschlussschraube screwed plug
903.2 Verschlussschraube screwed plug
906 Laufradschraube impeller screw
920 6kt Mutter hexagon nut
920.1 6kt Mutter hexagon nut
940 Passfeder key
950 Feder spring
970 Schild shield
800
940
441
970
561
230
524
137101
411
903
411.1
903.1
550.2
901.2
550
906
920
047
550.3
950 550.1
920.1
550.1
901.1
411.1
903.2
900
1)
2)
1) 35/55/65
2) 14/30/50/60
3) nur bei V 155-14/50/55 / for V 155-14/50/55 only
Assembly Instructions V 30 - 430
Speck Pumpen Vakuumtechnik GmbH
zertifiziert: DIN EN ISO 9001
10
Title: Mounting Instructions V 30 - 430
Edition: 02/03
Address
Speck Pumpen Vakuumtechnik GmbH
Regensburger Ring 6
D-91154 Roth
Phone: (49) 09171/809-0
Fax: (49) 09171/809-10
e-mail: info@speck-pumps.de
internet:http://www.speck-pumps.de
Any reproduction is allowed with the express
permission of SPECK Pumpenfabrik only.
Questo manuale è adatto per i seguenti modelli
5
Indice
Altri manuali Speck pumpen Pompa dell'acqua
Speck pumpen
Speck pumpen BADU Tec Picco Series Manuale utente
Speck pumpen
Speck pumpen V Series Manuale utente
Speck pumpen
Speck pumpen INOVA ND 25/40 Manuale utente
Speck pumpen
Speck pumpen IN Series Manuale utente
Speck pumpen
Speck pumpen 2 VGX Series Manuale utente
Speck pumpen
Speck pumpen BADU TEC 21 Series Manuale utente
Speck pumpen
Speck pumpen BADU Tec 42 Manuale utente
Speck pumpen
Speck pumpen Zismatic 40/10 WE Manuale utente
Speck pumpen
Speck pumpen BADU Jet Primavera Manuale utente
Speck pumpen
Speck pumpen BADU Eco Touch-pro Manuale utente
Speck pumpen
Speck pumpen BADU TEC I-Star Series Manuale utente
Speck pumpen
Speck pumpen B9 Series Manuale utente
Speck pumpen
Speck pumpen Zismatic 40/08 WE Manuale del proprietario
Speck pumpen
Speck pumpen BADU 90/40 Eco MV-E Manuale utente
Speck pumpen
Speck pumpen VGX 7/7 Manuale utente
Speck pumpen
Speck pumpen Normblock Istruzioni per l'installazione
Speck pumpen
Speck pumpen IN-VB-S Manuale del proprietario
Speck pumpen
Speck pumpen Aquacell A Series Manuale utente
Speck pumpen
Speck pumpen SUPS Manuale del proprietario
Speck pumpen
Speck pumpen BADU Spyder I Manuale utente
Manuali Pompa dell'acqua popolari di altre marche
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi
DUROMAX
DUROMAX XP WX Series Manuale utente
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manuale utente
Franklin Electric
Franklin Electric IPS Manuale utente
Xylem
Xylem e-1532 Series Manuale utente
Milton Roy
Milton Roy PRIMEROYAL Manuale utente