Spectracom VersaPNT Manuale utente

VersaPNT

Getting Started Guide

Document Part No.: 1228-5000-0057

Revision: 2.0

Date: 5-September-2018

About this Guide

This Getting Started Guide is a supplement to the main user manual for VersaPNT. The latest ver-

sion of the main user manual can be found online under manuals.spectracom.com.

Orolia USA, Inc. dba Spectracom

2CHAPTER 1•VersaPNT Getting Started Guide Rev. 2.0

CONTENTS

VersaPNT Getting Started Guide • TABLE OF CONTENTS i

Product Overview 1

1.1 Interfaces Overview 1

1.1.1 Input Timing Interfaces 2

1.1.2 Output Timing Interfaces 2

1.1.3 Navigation Inputs & Outputs 2

1.1.4 Other Interfaces 3

1.2 Connectors and their Pinouts 4

1.2.1 Power Connector 4

1.2.2 Input/Output Connector 4

1.2.3 Ethernet Connector 5

1.2.4 Optional I/O Connector 6

1.2.5 Coaxial Connectors 6

1.3 Included Cables 7

1.4 Status LEDs 9

1.4.1 Blinking Intervals 9

1.4.2 LED Lighting Patterns 9

1.4.3 Legend, individual LEDs 10

1.4.3.1 LED Patterns during Boot Sequence 11

1.4.4 Blackout Mode 11

1.5 The VersaPNT Web UI 11

1.5.1 The Web UI HOME Screen 11

Quick Start 13

2.1 Network Setup 14

2.2 Zero Configuration Setup 19

2.2.1 Using Zeroconf 20

2.3 Assigning I/O Pins 21

2.3.1 Signal Types 21

2.3.2 I/O Signal Mapping Table 22

2.4 INS Configuration 26

2.4.1 "IMU Output" Tab 27

2.4.2 "Calibration" Tab/Antenna Installation 29

2.4.3 "Log" Tab 31

2.4.4 "FIR Filter" Tab 31

2.4.5 "Coning/Sculling" Tab 32

2.4.6 "Frame Rotation" Tab 33

2.5 INS Initialization 34

2.6 INS Expert Mode 35

2.7 VICTORY Configuration 36

SAFETY 37

3.1 SAFETY: Before You Begin Installation 37

Technical Support 39

4.1 Regional Contact 39

ii VersaPNT Getting Started Guide • TABLE OF CONTENTS

Product Overview

This section is designed to help you become familiar with the structure, features, and functions

of the VersaPNT.

1.1 Interfaces Overview

All of VersaPNT's interfaces are integrated into the unit's connectors, which are located on the

front panel:

Figure 1-1: VersaPNT front panel connectors

Note: VersaPNT is highly configurable and the connections can be adjusted many

different ways. Your interface configuration may vary based on options you selec-

ted during the ordering process.

The following interfaces are provided:

1.1 Interfaces Overview

CHAPTER 1•VersaPNT Getting Started Guide Rev. 2.0 1

1.1.1 Input Timing Interfaces

Table 1-1: VersaPNT timing inputs

INPUTSIGNAL Total

available

DCLS RS-232 RS-485 ETH Connector No.

(see Fig. above)

TTL 10V

1PPS (1) 1 4

ASCII/HaveQuick/IRIG B (1) 1 4

ASCII/NMEA (1) 1 4

Network Interface (10/100/1000bT):

NTP (Stratum 2), PTP

(2) 1 5

1.1.2 Output Timing Interfaces

Table 1-2: VersaPNT timing outputs

OUTPUTSIGNAL Total

available

DCLS RS- 232 RS-485 ETH Connector No.

(see Fig. above)

TTL 10V

10 MHz (1+3) SMA 3

1PPS (2) 1 1 4

ASCII/HaveQuick (1) 1 4

ASCII/NMEA (1) 1 4

NTP server,

PTP v2 master

(1) 1 5

All Multi I/O interfaces (connector no. 4) are software-configurable, see "Assigning I/O Pins"

on page21.

1.1.3 Navigation Inputs & Outputs

The following VersaPNT options apply to the INS option board. The standard INS

OUTconnection will communicate your position and navigation information, while the Options

1-8 provide additional information via the multi I/O connector:

Table 1-3: Navigation input and output options

SIGNAL TYPE Option Number/

Channel Position

DCLS RS- 232 RS-422

(n or p)

Connector No.

(see Fig. above)

TTL

INS OUT Channels 1, 4, & 6 1 4

PPS IN Option & Channel 1 1 4

PPS OUT Option & Channel 2 1 4

2CHAPTER 1•VersaPNT Getting Started Guide Rev. 2.0

1.1 Interfaces Overview

SIGNAL TYPE Option Number/

Channel Position

DCLS RS- 232 RS-422

(n or p)

Connector No.

(see Fig. above)

TTL

GPS IN Option & Channel 3 1 4

GPS OUT Option & Channel 4 1 4

IMU IN Option & Channel 5 1 (p) 4

IMU IN Option & Channel 6 1 (n) 4

IMU OUT Option & Channel 7 1 (p) 4

IMU OUT Option & Channel 8 1 (n) 4

1.1.4 Other Interfaces

USB serial equivalent: CLI interface (Connector 4)

1.1 Interfaces Overview

CHAPTER 1•VersaPNT Getting Started Guide Rev. 2.0 3

1.2 Connectors and their Pinouts

All of VersaPNT's connectors are provided at the front panel of the unit, below the Status LEDs.

1.2.1 Power Connector

Note: View in mating direction from front.

Table 1-4: Power connector pinout

Pin Signal

1 VMain (10 to 32V)

2 VMain (10 to 32 V)

3 VBatt (10 to 32 V)

4 GND

5 GND

1.2.2 Input/Output Connector

VersaPNT has a 26-pin input/output connector that offers 8 software-configurable CHANNELS,

plus one fixed DCLS channel, and a USB interface. To learn more about types of interfaces and

signals, and how to configure them, see "Assigning I/O Pins" on page21.

4CHAPTER 1•VersaPNT Getting Started Guide Rev. 2.0

1.2 Connectors and their Pinouts

Table 1-5: Default I/O connector pinout

Pin Channel Signal Pin Channel Signal

10 1PPS output (5V) 15 7 Have Quick output (RS-

485 signal +)

2GND 16 GND

31 HaveQuick input (RS-

485 signal +)

17 8 Have Quick output (RS-

485 signal –)

4GND 18 GND

52 HaveQuick input (RS-

485 signal –)

19 9

(USB ded-

icated)

GND

6GND 20 GND

73 1PPS output (10 V) 21 Not connected

8GND 22 GND

94 ASCII output (RS-232) 23 USB D–

10 GND 24 GND

11 5 1PPS input 25 USB D+

12 GND 26 GND

13 6 ASCII input (RS-232)

14 GND

1.2.3 Ethernet Connector

Note: View in mating direction from front.

1.2 Connectors and their Pinouts

CHAPTER 1•VersaPNT Getting Started Guide Rev. 2.0 5

Table 1-6: Ethernet connector pinout

Pin Signal Pin Signal

1 Ethernet_1 A+ 9 Ethernet_2 A+

2 Ethernet_1 A– 10 Ethernet_2 A–

3 Ethernet_1 B+ 11 Ethernet_2 B+

4 Ethernet_1 B– 12 Ethernet_2 B–

5 Ethernet_1 C+ 13 Ethernet_2 C+

6 Ethernet_1 C– 14 Ethernet_2 C–

7 Ethernet_1 D+ 15 Ethernet_2 D+

8 Ethernet_1 D– 16 Ethernet_2 D–

1.2.4 Optional I/O Connector

The Optional I/O connector is used in conjunction with the Option Board that is available for

VersaPNT. If the unit is not equipped with an Option Board, this connector is not used.

1.2.5 Coaxial Connectors

VersaPNT offers five (5) coaxial connectors, three (3) of which can be configured at the factory

to accommodate requirements for e.g., IRIG AM signals or additional 10MHz outputs. The min-

imum configuration includes the GNSS antenna and a 10MHz sinewave output.

Unless otherwise ordered at the factory, all coaxial connectors (aside from the GNSS con-

nection) produce a 10MHz output that is not software configurable.

All coaxial connectors are standard SMA connectors.

ETHERNET connector wiring:

1 through 8: A Ethernet Connect, 4 pairs, 1000bT

9 through 16: B Ethernet Connect, 4 pairs, 1000bT

POWER connector pinout

1; 2: VMain, 10 to 32 VDC

3: VBatt, 10 to 32 VDC (Standby Power)

4; 5: Ground return

6CHAPTER 1•VersaPNT Getting Started Guide Rev. 2.0

1.2 Connectors and their Pinouts

Indice

Altri manuali Spectracom GPS

Spectracom

Spectracom 2804A Manuale utente

Manuali GPS popolari di altre marche

Raven

Raven Cruizer II Manuale

Hama

Hama 53118 Manuale utente

Garmin

Garmin SOUNDER 125 Manuale utente

Garmin

Garmin DEZL 580 Manuale utente

Jigabot

Jigabot EX Manuale utente

Pointer

Pointer Cellocator CelloTrack XT LTE Guida all'installazione

Queclink

Queclink GV55LITE Manuale utente

Voxson

Voxson Voxtrack GPS500 Manuale di istruzioni

Garmin

Garmin ECHOMAP PLUS Manuale utente

Starcom Systems

Starcom Systems Kylos Compact Manuale utente

Garmin

Garmin 15 H Series Manuale utente

Cobra

Cobra Marine MC 600Ci Manuale utente

Cellocator

Cellocator CelloTrack T Manuale utente

Enfora

Enfora Mini-MT GSM2228UG001 Manuale utente

Magellan

Magellan eXplorist 100 Manuale utente

LTE

LTE G50B Manuale utente

Garmin

Garmin DEZL OTR500 Manuale utente

SkyGolf

SkyGolf SkyCaddie SG1 Manuale utente