Spectrum Digital XDS510USB Manuale utente
1
XDS510USB JTAG Emulator
Installation Guide
IMPORTANT INFORMATION
About This Installation Guide
This Installation Guide is for the XDS510USB Emulator product. The XDS510USB Emulator
is a module to be attached to a PC for hardware engineers and software programmers to develop
DSP applications.
The text paragraphs in this Guide are very important for proper device functioning and for
preventing any possible damages on the XDS510USB Emulator device and project target board.
These paragraphs are shaded as in the following example. Please carefully read each of the
shaded text.
This is an example of a very important text paragraph mentioned above.
Introduction
Overview
XDS510USB Emulator is designed to use with digital signal processors (DSPS) operating at
1.0-5.0 volts. The emulator itself is a bus-powered USB device. It is fully plug and play
compatible and is fully powered by the host computer’s USB connection. The XDS510USB
Emulator operates with TI Code Composer Studio IDE debug tool and is fully compatible with
windows 98/SE/ME/2000/XP/VISTA.
Features
XDS510USB Emulator has the following features:
●
Supports Texas Instruments DSP with a JTAG (IEEE1149.1) interface: C2000, C5000,
C6000 ,OMAP platforms.
●
Supports Texas Instruments Code Composer Studio.
●
Supports 1.0-5.0 volt DSP devices.
●
USB compatible. Simple Connection, fully Plug-and-Play compatible-no jumpers, noswitch
settings.
●
Hot pluggable
●
Power provided by USB bus , no additional power supply is required.
2
QUICK Installation
Quick Install Procedures
This guide describes the steps to installing the XDS510USB Emulator in the following orders:
1. Install the XDS510USB Emulator hardware
2. Install the XDS510USB device driver
3. Make sure Code Composer Studio IDE is installed on the PC
4. Install the XDS510USB Emulator software
5. Configure Code Composer Studio IDE
6. Reset the XDS510USB Emulator and Reset the target DSP
7. Run CCS
The XDS510USB JTAG Emulator kit contains:
●
XDS510USB JTAG Emulator
●
USB interface cable
●
The XDS510USB driver disk
●
XDS510USB Emulator Installation Guide Reference Guide (this document)
Installation Requirements
●
Code Composer Studio IDE 1.2 or greater
●
A free USB port
●
233 MHZ or higher Pentium compatible CPU (500MHZ or higher Pentium III CPU or
equivalent is recommended)
●
Local CD-ROM drive
Supported Operating Systems
●
Windows98/ME/2000/XP/VISTA
Detailed Installation
What you will need
The following detailed list contains all items needed to install and run with the XDS510USB
JTAG Emulator.
●
PC with a free Universal Serial Bus (USB) port
●
XDS510USB JTAG Emulator
●
XDS510USB driver disk
●
USB interface cable
●
DSP target system
●
Code Composer Studio
3
The Hardware Installation
●
Remove power from the target DSP system.
●
Connect the keyed XDS510USB JTAG Emulator JTAG interface cable to the target board.
●
Apply power to the target DSP system.
●
Connect the XDS510USB JTAG Emulator to the host computer system using a USB cable.
The USB Device Drivers Installation
Driver installation for windows 2000/XP:
1. After plug the XDS510USB JTAG Emulator into the host computer’s USB port, the system
should display the Found New Hardware (Figure A-1) dialog box. This dialog box indicates
the computer operating system has found a new USB device.
Figure A-1
2. The system will prompt for new hardware detected and start the “Found New Hardware
Wizard” as shown in Figure A-2.
4
Figure A-2
3. Click on next and system will display the window as shown in Figure A-3.
Figure A-3
4. Check on “Search for a suitable driver for my device(Recommended)” and click on next. The
system will display a window as shown in Figure A-4.
5
Figure A-4
5. Check on “CD-ROM drives” and click on next. The system will prompt you to insert the
manufacturer’s installation disk, as shown in the Figure A-5.
Figure A-5
6. Click on Browse and locate the file usb510.Inf in the installation CD(TI DSP
Emulator\XDS510 USB_driver), or in the folder where you have downloaded the file into, as
shown in Figure A-6.
Figure A-6
7. Click on next, the following window will be displayed ,as shown in Figure A-7.
6
Figure A-7
8. Click on Finish. Set up is completed.
Installing the XDS510USB software
This installation assumes that the Code Composer Studio IDE has already been installed on
the PC. If not, please follow the directions for installing Code Composer Studio first. After
completing the installation procedure, you may return to the guide to complete the installation
procedure of the XDS510 Emulator.
Insert the XDS510USB driver disk into your CD-ROM, Double click on Setup.Exe(TI DSP
Emulator\XDS510 CCS_driver) to install the JTAG emulator tools for CCS.
In order to run the
application properly the XDS510 CCS Driver must reside in the same folder in which the
Code Composer Studio IDE is installed.For example,if the Code Composer Studio IDE
installed in E:\CCStudio_v3.3,the XDS510 CCS Driver must install in E:\CCStudio_v3.3.
NOTE
Be sure the Code Composer Studio has been installed before run Setup.exe. It’ll copy
files to the CCS install directory and create environment variable to enable the file usage
by CCS. If this step is missing, the XDS510USB can’t function properly.
7
8
CCS Emulate Configuration
9
XDS510USB JTAG Emulator has provided many typical emulate configuration. The user can
use them directly without modification.
1. Launch the Setup CCStudio v3.3 , the program will display the window as shown
in figure C-1.
Figure C-1
2. Select xds510 emulator in the platform list; Select your DSP type in the family list. The
program will list some typical configuration.
3. Double-click the item according to your target board .The new configuration will appear in
My System list in the System Configuration window.Configure the properties of your target
board and Set the proper gel file. Save the configuration and exit the setup program.
4. Connect your target board to the emulator, then power on the target board, launch the CCS.
Now, you can debug your target system using XDS510USB JTAG Emulator.
10
Figure C-2
Figure C-3
Indice
Altri manuali Spectrum Digital Hardware per computer
Spectrum Digital
Spectrum Digital C2000 Series Manuale per l'uso e la cura
Spectrum Digital
Spectrum Digital TMS320C5515 eZdsp Manuale per l'uso e la cura
Spectrum Digital
Spectrum Digital XDS560v2 Manuale per l'uso e la cura
Spectrum Digital
Spectrum Digital XDS560R Manuale di istruzioni
Spectrum Digital
Spectrum Digital XDS510PP Manuale utente
Spectrum Digital
Spectrum Digital AppBox C21 Manuale utente
Spectrum Digital
Spectrum Digital XDS560R Manuale utente
Spectrum Digital
Spectrum Digital XEVM642 4VSX35 Manuale per l'uso e la cura
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
