Spektrum DX6C Manuale utente

Instruction Manual

Bedienungsanleitung

Manuel d’utilisation

Manuale di Istruzioni

DX6C

6-Channel 2.4GHz

DSMR®Radio System

Scan the QR code and select

the Manuals & Support tab

from the product page

or the most up-to-date

information

2SPEKTRUM DX6C • TRANSMITTER INSTRUCTION MANUAL

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating.

Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechani-

cal ability. Failure to operate this product in a safe and responsible manner could result in injury or damage to the product or

other property. This product is not intended for use by children without direct adult supervision. Do not attempt disassembly, use

with incompatible components or augment product in any way without the approval of Horizon Hobby, LLC. This manual contains

instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual,

prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

WARNING AGAINST COUNTERFEIT PRODUCTS

Always purchase from a Horizon Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum product. Horizon

Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit

products or products claiming compatibility with DSM or Spektrum technology.

Age Recommendation: Not for Children under 14 years. This is not a toy.

WARRANTY REGISTRATION

Visit community.spektrumrc.com today to register your product.

SAFETY PRECAUTIONS

• Always ensure all batteries have been properly charged prior

to using the model.

• Always check all servos and their connections prior to each run.

• Never operate your model near spectators, parking areas or any oth-

er area that could result in injury to people or damage of property.

• Never operate your model during adverse weather conditions. Poor

visibility can cause disorientation and loss of control of your model.

• Never point the transmitter antenna directly toward the model. The

radiation pattern from the tip of the antenna is inherently low.

• If at any time during the operation of your model you observe any er-

ratic or abnormal operation, immediately stop operation of your model

until the cause of the problem has been ascertained and corrected.

NOTICE:All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For

up-to-date product literature, visit horizonhobby.com or TowerHobbies.com and click on the support or resources tab for this Product.

MEANING OF SPECIAL LANGUAGE

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage and serious

injury OR create a high probability of superﬁcial injury.

CAUTION:Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

NOTICE:Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.

NOTICE: This product is only intended for use with unmanned, hobby-grade, remote-controlled vehicles and aircraft. Horizon Hobby

disclaims all liability outside of the intended purpose and will not provide warranty service related thereto.

SPEKTRUM DX6 • TRANSMITTER INSTRUCTION MANUAL

TABLE OF CONTENTS

Spektrum SR315 Sport Surface Receiver.......................................4

Typical Electric Vehicle Installation ...................................................4

Typical Nitro Vehicle Installation .......................................................4

Receiver compatibility .....................................................................4

Receiver Antenna............................................................................4

Binding ..........................................................................................4

Failsafe..........................................................................................4

DX6C Controls and Switches ..........................................................5

Installing Batteries..........................................................................5

Main Screen....................................................................................5

Navigation.......................................................................................6

Using the Scroll wheel Selector........................................................6

Individual Direction Adjustments ......................................................6

Auto Switch Select..........................................................................6

Switch Selection tip ........................................................................6

Click..............................................................................................6

Scroll.............................................................................................6

Hold...............................................................................................6

Menu...............................................................................................7

Model Select ..................................................................................7

Model Name...................................................................................7

Travel.............................................................................................8

Sub-Trim........................................................................................8

Reverse .........................................................................................8

Speed............................................................................................8

Rates.............................................................................................9

Exponential ....................................................................................9

Timer.............................................................................................9

Bind/Frame Menu ........................................................................10

mixing..........................................................................................11

Steering Mix.................................................................................11

programmable mix........................................................................11

AVC Programming Menu...............................................................12

Trim setup....................................................................................12

Trim ASSIGN.................................................................................12

AUX assign...................................................................................12

Telemetry.....................................................................................13

settings........................................................................................14

settings (continued) ......................................................................15

Calibrate ......................................................................................15

Utilities..........................................................................................15

Model Select ................................................................................15

Model Utilities...............................................................................15

Model Utilities (continued) .............................................................16

PHYSICAL TRANSMITTER ADJUSTMENTS .....................................17

Standard Wheel Conversion...........................................................17

Steering Tension Adjustment ........................................................17

Data Port .....................................................................................17

AVC TUNING (avc receiver not included).........................................18

What Is Gain?...............................................................................18

What is Priority? ...........................................................................18

What Is Heading Hold?..................................................................18

AVC Tuning Procedure...................................................................18

General Tuning Tips ......................................................................18

Changing Battery Voltage ..............................................................18

Troubleshooting Guide..................................................................19

Problem.......................................................................................19

Possible Cause.............................................................................19

Solution .......................................................................................19

AVC Troubleshooting Guide...........................................................19

Problem.......................................................................................19

Possible Cause.............................................................................19

Solution .......................................................................................19

Optional parts list .........................................................................19

Part # ..........................................................................................19

parts description...........................................................................19

1-Year Limited Warranty...............................................................20

Warranty and Service Contact Information...................................21

FCC Information............................................................................21

IC Information...............................................................................22

Compliance Information for the European Union..........................22

BOX CONTENTS

The DX6C transmitter is compatible with Spektrum™DSMR®and DSM2® Receivers.

The DX6C is available with and without a receiver, they are both covered in this manual

• SPM6125 includes the SR315 DSMR receiver

• SPMR6125 is a tranmistter only package and does not include a receiver

With included SR315 Receiver

(without AVC)

1. Install batteries in transmitter

2. Press and hold the bind button on the receiver

and then turn on vehicle

3. Turn transmitter on and put it in bind mode

4. Set up servo reverse, travel, and sub trim

5. Re-bind to set proper failsafe positions

GETTING STARTED DAILY DRIVING

1. Turn on transmitter ﬁrst

2. Turn on vehicle*

3. Turn off vehicle ﬁrst

4. Turn off transmitter

SPECIFICATIONS

DX6C SR315

Type 6-Channel DSMR 3-Channel DSMR Sport Receiver

Dimensions (L × W × H) 160mm x 122mmx 251mm 32.5mm× 21.5mm × 13.4mm

Antenna Length Integrated 90mm

Channels 6 3

Weight 402 6g

Band 2402 MHz – 2478 MHz

Voltage Range 3.5–9.6V

4SPEKTRUM DX6C • TRANSMITTER INSTRUCTION MANUAL

TYPICAL ELECTRIC VEHICLE INSTALLATION TYPICAL NITRO VEHICLE INSTALLATION

SPEKTRUM SR315 SPORT SURFACE RECEIVER

STR THR AUX1 BATT

WARNING: Do not kink,

cut or damage the

antenna wire. The antenna is

made of a coaxial wire; if the

outer sheath becomes

damaged, the receiver will not

work properly. If the antenna is

damaged in any way, replace

the antenna before attempting

to use the receiver.

RECEIVER ANTENNA

The SR315 receiver features a coaxial antenna design for easy

installation in almost any model. Think of the last 1 inch (32mm)

on the tip of the antenna as the active portion of the antenna,

the coaxial portion leading up to it is just an extension. Install the

antenna so the active portion is positioned as high as possible in

the vehicle, and not “in the shadow” of any carbon ﬁber or metal.

Standard Mode

If loss of signal occurs,

SmartSafe™ technology

moves the throttle channel to its

designated failsafe position (low

throttle) that was set during binding.

All other channels hold their last

position.When the receiver detects

signal from the transmitter, normal

operation resumes.

Gas Mode

Preset failsafe is ideal for most

nitro/gas vehicles. With preset

failsafe, all channels go to their

preset failsafe positions if the

signal is lost, preventing an

out of control situation. When

the receiver detects signal

from the transmitter, normal

operation resumes.

Gas Mode

1 Push and Hold Bind Button

2Power on Reciever, keep Bind button depressed until

binding is complete

3 Place transmitter in Bind Mode and ﬁnish Binding

4When the LED turns solid, power off the reicever, and then

release the Bind Button

Standard Mode

1 Push and Hold Bind Button

2 Power on Reciever

3Release Button after RX goes into Bind Mode (ﬂashing LED)

4 Place transmitter in Bind Mode and ﬁnish Binding

FAILSAFE

Failsafe position is set during binding. In the unlikely event

that the radio link is lost during use, the receiver will drive all

channels to its pre-programmed failsafe position.

Bind Button

Active portion

of antenna

Antenna Tube Not

Included. Tube size

may vary, test for

proper ﬁt.

BINDING

The SR315 receivers must

be bound to the transmitter

before they will operate.

Binding is the process

of teaching the receiver

the speciﬁc code of the

transmitter so it will only

connect to that speciﬁc

transmitter.

RECEIVER COMPATIBILITY

The SR315 receiver is compatible with

Spektrum DSM2®and DSMR®radio

control surface systems. Install the

receiver in the position recommended by

the vehicle’s manufacturer. Double-sided

tape or foam may be used to secure the

receiver in place.

The case of the receiver can accept an antenna tube directly, making

optimal antenna placement easy (antenna tube not included).

Battery

Throttle Servo

Steering Servo

Receiver

Electronic

Speed Control

To Motor

SPEKTRUM DX6 • TRANSMITTER INSTRUCTION MANUAL

INSTALLING BATTERIES

1. Remove the battery cover from the bottom of the

transmitter.

2. Install 4 AA batteries as shown.

3. Install the battery cover.

DX6C CONTROLS AND SWITCHES

A: Trimmer Button A

Default- Throttle Trim

B: Trimmer Button B

Default- Steering Trim

C: Trimmer Button C

D: Trimmer Button D

E: Trimmer Button E

Default- Steering Rate Up

F: Trimmer Button F

Default- Brake Rate Up

G: Button G

Default- Timer Start/Stop

H: Power Button

I: Roller Wheel

J: Antenna

K: Steering Wheel

L: Trigger (throttle/brake)

M: Battery Door

N: Data Port

O: LCD Screen

P: Back Button

Q: Clear Button

The Main Screen displays information about the active model,

including the Timer (when activated). To return to the Main

Screen at any time, press and hold the scroll wheel for at least

6 seconds.

A: Transmitter Battery Voltage

B: Model Name

C: Steering Rate

D: Timer (when activated)

E: Position of Steering (STR) trim

F: Position of Throttle (THR) trim

G: Position of Brake (BRK) trim

H: Position of AUX 1 trim

I: Position of AUX 2 trim

J: Position of AUX 3 trim

MAIN SCREEN

CAUTION: NEVER remove the transmitter batteries

while the model is powered on. Loss of model control,

damage or injury may occur.

CAUTION: If using rechargeable batteries, charge only

rechargeable batteries. Charging non-rechargeable

batteries may cause the batteries to burst, resulting in injury to

persons and/or damage to property.

CAUTION: Risk of explosion if battery is replaced by an incorrect

type. Dispose of used batteries according to national regulations.

6SPEKTRUM DX6C • TRANSMITTER INSTRUCTION MANUAL

Tip: The tick mark below shows the

current switch position.

Use the slide button and press OK to turn

the selected box black, indicating that the

value or condition will act on that position.

AUTO SWITCH SELECT

To easily select a switch in a function, such as a program mix,

use the slide button to highlight the switch selection box, and

press OK. The box around the switch should now ﬂash. To select

a switch, toggle the switch you wish to select. Verify the switch

selection is now displayed as desired. When correct, press OK to

select this switch and complete the switch selection.

SWITCH SELECTION TIP

If the system won’t allow INHIBIT to be changed, all switches are

assigned to a different function. Un-assign a switch from another

function to free it up for selection.

The DX6C does not allow switch assignments to be over-loaded,

there is only one switch to one function. Once a switch is

conﬁgured for a function, the switch assignment for that function

must be disabled for the switch to be used for something else.

INDIVIDUAL DIRECTION ADJUSTMENTS

In some instances, you may ﬁnd it necessary to independently

adjust the control directions; for example, if you want more travel

for left steering than right steering, perform the following steps:

1. Slide to the value you wish to change and press OK

2. When both directions are selected, move the control (steer-

ing or throttle) toward the control direction you wish to

change. The selection box moves to the desired direction.

You do not need to hold the control in the desired direction.

3. To change the opposite direction, simply move the control

in that direction.

4. Press OK to save the selection.

USING THE SCROLL WHEEL SELECTOR

• Scroll the scroll wheel to move through the screen content or

change programming values. Click the scroll wheel to make a

selection.

• Use the Back Button to go back to go to the previous screen (for

example, to go from the Mixing Screen to the Function List).

• Use the Clear Button to return a selected value on a screen to

the default setting.

• The Main Screen appears when you power on the transmitter.

Click the scroll wheel once to display the Function List.

Turn

Press

To Enter, Select or

Exit a selection.

To move between

options or change

values in an option.

Hold for 6 seconds and

release to return to the

Main screen.

SCROLL HOLDCLICK

NAVIGATION

SPEKTRUM DX6 • TRANSMITTER INSTRUCTION MANUAL

MODEL SELECT

Model Select enables you to access any of the 20 internal model memory locations in the Model Select list.

1. Scroll to the desired model memory in the Model Select list.

2. When the desired model memory is highlighted, press OK once to select the model. The transmitter

returns to the Main Screen.

3. Add a new model by rolling to the bottom of the list. You will then be prompted with the Create New

Model screen, with the option to create a new model or cancel. If you select Cancel, the system will

return to the Model Select function. If you select Create, the new model will be created and now be avail-

able in the model select list.

CAUTION: NEVER change the model in Model Select while operating a model. Changing the model

memory interrupts the transmitter signal to the receiver and may cause loss of vehicle control, damage

or personal injury.

Click the scroll wheel from the main screen to access the FUNCTION LIST. The FUNCTION LIST contains all the available menus on the

DX6C. The functions include:

• Model Select

• Model Name

• Travel

• Sub Trim

• Reverse

• Speed

• Rates

• Exponential

• Timer

• Bind/ Frame Rate

• Mixing

• AVC

• Trim Setup

• Aux Assign

• USB Settings

• System Settings

• System Setup

MODEL NAME

Model Name enables you to assign a custom name to the current model memory. Model names can include up

to 15 characters, including spaces.

To add letters to a Model Name:

1. Slide to the desired letter position and press OK. A ﬂashing box appears.

2. Slide Up or Down until the desired character appears. Press OK to save the character.

3. Slide to the next desired letter position. Repeat Steps 1 and 2 until the Model Name is complete.

4. Select Back Button to return to the MENU.

To erase a character(s):

5. Press the Clear button while the character is selected.

6. Press the Clear button a second time to erase all characters to the right of the cursor.

8SPEKTRUM DX6C • TRANSMITTER INSTRUCTION MANUAL

TRAVEL

The Servo Setup menu contains the following functions:

Travel sets the overall travel or endpoints of the servo arm movement. Travel values range from 0–150%

(Default is 100%).

To adjust Travel values:

1. Slide to the channel you wish to adjust and press OK.

2. Slide Up or Down to adjust the travel value. Press OK to save the selection.

SUB-TRIM

Subtrim offsets the entire range of servo travel including the center and endpoint positions.

CAUTION Use only small sub-trim values may affect travel if full servo travel is used.

REVERSE

Use the Reverse menu to reverse the channel direction. For example, if the Steering servo moves Left,

reversing the channel will move the Steering servo Right.

To reverse a channel direction:

1. Slide to Travel and press OK. Slide up or down until Reverse appears, then press OK again to save the

selection.

2. Slide to the channel you wish to reverse and press OK.

If you reverse the Throttle channel, a conﬁrmation screen appears. Select YES to reverse the channel. A second

screen appears, reminding you to bind your transmitter and receiver.

CAUTION: Always rebind the transmitter and receiver after reversing the Throttle channel. Failure to do so will result in the

throttle moving to full throttle if failsafe activates.

Always perform a control test after making adjustments to conﬁrm the vehicle responds properly.

CAUTION: After adjusting servos, always rebind the transmitter and receiver to set the failsafe position.

SPEED

The Speed menu enables you to slow the response time on any individual channel.

The Speed is adjustable from 100% to 1%.

To adjust the Speed:

1. Slide to the channel you wish to adjust and press OK.

2. Slide Up or Down to adjust the speed and press OK to save the selection.

3. Select a switch to activate/deactivate the function. If Switch ON is selected, the value will always be on for that function.

SPEKTRUM DX6 • TRANSMITTER INSTRUCTION MANUAL

RATES

EXPONENTIAL

TIMER

Rates allow the driver to reduce the travel (0-100%) of the Steering, Throttle, or Braking with a trimmer

button. The Override option allows drivers to select a different rate value (0-125%) while holding down the

assigned trimmer button. This is especially helpful for oval racers that program minimal steering throw to

desensitize steering during racing, but requires maximum steering angle to drive out of a crash or get turned

around on the track.

To adjust Rate values:

1. Slide to Steering and press OK to select between Steering, Throttle or Brake.

2. Slide Up or Down to adjust the Rate value. Press OK to save the selection.

3. Set the Switch setting to On to enable Rates, select Inh to disable Rates.

4. Select an Override rate and switch.

5. Select the OTF (On-The-Fly) trimmer that will be used to adjust Rates On-The-Fly.

TIP: In order for the OVERRIDE to operate, you must assign it to a switch or trimmer. The default position

for this function is inhibited.

The Exponential (Expo) function affects the response rate of the steering, throttle and/or brake. A positive

Steering Expo value, for example, decreases steering sensitivity around neutral to make it easier to drive at

high speeds in a straight line while still allowing for maximum turning radius. While sensitivity with positive

Expo is decreased around neutral, it increases the sensitivity near the end of travel.

To adjust Expo values:

1. Select Throttle or Steering.

2. Slide Up or Down to adjust the Rate value.

3. Press OK to save the selection.

4. Select an OTF switch to activate Exponential.

IMPORTANT: Both positive and negative Expo values are available. A positive Expo value results in the

center being less sensitive (desirable most of the time), while a negative value increases the sensitivity

around center (normally not used).

The DX6C Timer function allows you to program a countdown timer and stop watch (count up timer) to display on the main screen.

An alarm sounds when the programmed time is reached. You can program the timer to start using the assigned switch position or

automatically when the throttle moves above a pre-programmed position.

Rates

Steering

Rate:100%

Switch:On

OTF

Trim:E

Inh

Override

Rate:100%

Switch:Inh

≥

10 SPEKTRUM DX6C • TRANSMITTER INSTRUCTION MANUAL

Binding

Binding is the Process of teaching the receiver the speciﬁc transmitter’s code called GUID (Globally Unique

Identiﬁer) and storing failsafe values. When a receiver is bound to a transmitter/model memory, the receiver will

only respond to that speciﬁc transmitter/model memory.

Bind Process

1. Use a bind plug or press the bind button to place the receiver into Bind mode. The LED on the receiver

will begin to ﬂash.

2. Power on the transmitter.

3. Select the Model Memory you wish to bind to.

4. Select Bind from the List menu.

5. Move the throttle channel to the desired failsafe position.

NOTICE: The throttle channel must stay in the failsafe position until binding is complete.

6. Slide to Bind and press OK. The orange LED ﬂashes on top of the transmitter.

7. When the bind process is complete, the transmitter and receiver LEDs stop ﬂashing and turn solid

orange.

8. Remove the bind plug from the receiver and keep it in a convenient place.

IMPORTANT: Always remove the bind plug from the receiver when the bind Process is complete. Failure to

do so will cause the receiver to enter bind mode the next time you power on the receiver.

Failsafe

In the unlikely event that the radio link is lost during use, the receiver will drive the throttle servo to its pre-programmed failsafe posi-

tion (normally full brakes) and all other channels will have no servo output. The throttle failsafe position is set during binding. If the

receiver is turned on prior to turning on the transmitter, the receiver will enter the failsafe mode, driving the throttle servo to its preset

failsafe position. When the transmitter is turned on, normal control is resumed.

IMPORTANT: failsafe activates only in the event that signal is lost from the transmitter. Failsafe will NOT activate in the event that

receiver battery power decreases below the recommended minimums or power to the receiver is lost.

BIND/FRAME MENU

For compatibility with all types of servos, three frame rates are available:

• 11ms: Offers good response rates and is compatible with most digital and analog servos (this is the

default position). Works with DSMR®surface receivers.

• 16.5ms: Needed for older analog servos. Works with DSM2®surface receivers.

• 22ms: Needed for older analog servos. Works with DSMR receivers.

TIP: You should always use the fastest response rate the servos can handle. This gives the lowest latency

and fastest response. If the frame rate is incompatible with the servo, the servo will move erratically or, in

some cases, not at all. If this occurs, change the frame rate to the next highest value.

IMPORTANT: Always rebind after changing the Frame Rate.

NOTICE: AVC receivers must be calibrated after binding for proper operation.

BIND

1: Track

Frame Rate

11 ms

Put receiver into

Bind Mode

then select BIND

CANCEL

BIND

LIST

Indice

Altri manuali Spektrum Controller per videogiochi

Spektrum

Spektrum DX18 Manuale utente

Manuali Controller per videogiochi popolari di altre marche

Wasp

Wasp SL-6610 Manuale utente

JKG

JKG JKG2022A Manuale utente

Marvo

Marvo MG08 Manuale utente

Belkin

Belkin F8GBPC001 Manuale utente

GameSir

GameSir Z2 Manuale utente

Laser

Laser PCO-AGAMEC-BK Manuale utente

Cortex

Cortex VEXnet Manuale utente

Gioteck

Gioteck HF-1 Manuale utente

Nacon

Nacon DAIJA ARCADE STICK Manuale utente

Thrustmaster

Thrustmaster dual trigger Manuale utente

SHAKS

SHAKS S1+ Manuale utente

YCCTEAM

YCCTEAM Joy Con Manuale utente

Hyperkin

Hyperkin Smartboy Manuale utente

Nerf

Nerf DuraGrip Manuale utente

MoveMaster

MoveMaster MoveMaster Manuale utente

WinWing

WinWing Super Libra J1 Manuale utente

ECCI

ECCI Trackstar 6000 Series Manuale utente

Logitech

Logitech 963291-0403 - Attack 3 Joystick Manuale utente