Spinlock DURO SOLAS Manuale utente
Lifejacket Quick Service Guide
www.spinlock.co.uk
Date: February 2023
Registered design EC + US Patent No. 7631728
Issue Number: 5
DURO SOLAS
and
DURO SOLAS +
Contents
Service Station Requirements
1: Harness and cover
2: Quick Burst Zip Information
Deckvest Fitted with Ocean Signal MOB 1 AIS Device
3: Ination test
3.1: Bladder Replacement
3.2: Components for the UML Mk5 automatic ring head
3.3: Components
4: Cleaning
5: Re-attaching components and arming the lifejacket
6: Pylon and Lume - On
7: Zip replacement
8: Repacking
9: Rear Harness Loop Fitting instructions
If you need any assistance with servicing please contact
3
4
5
6
8
9
12
14
14
15
16
18
20
25
Issue Ammendments
2: Added new Pylon light text
3: Revised MOB1 tting instructions added
4: Bladder Attachments changed
5: Addition of SOLAS + Harness model
Rear harness tting instructions for SOLAS +
IMPORTANT LEGAL NOTICE
REGARDING USE OF DECKVEST SERVICE MANUAL
1. This Approved Service Manual (“Services Manual”) is for use only by those persons at an
Approved Deckvest Service Centre (“Service Centre”) who have completed the appropriate
Deckvest service training provided by Spinlock Ltd (“Spinlock”) or one of its appointed training
representatives (“Service Trainer”).
2. Servicing of a Deckvest life-jacket may only be undertaken by Spinlock or a person who has
received service training by Spinlock or a Service Trainer.
3. The procedures set out in this Service Manual must be followed in order to ensure the proper
and safe functioning of the Deckvest life-jacket. If the procedures set out in this Service Manual
are not properly followed and carried out there is a risk of accident or death.
4. It is the sole responsibility of the Service Centre to ensure that the service of the Deckvest
lifejacket is carried out fully in compliance with the procedures set out in this Service Manual
and in accordance with the training that they have received.
5. The signature or stamp of or on behalf of the Service Centre on a Deckvest Service Sheet shall
be deemed to be the Service Centre’s acknowledgment and conrmation that the service of the
Deckvest life-jacket has been carried out in accordance with this Service Manual and the
relevant service training.
6. Spinlock Limited (and its agents) reserves the right (but without accepting any obligation
to audit the procedures being followed by a Service Centre to ensure adequate standards and
compliance with this Service Manual.
7. Save for death or personal injury caused by the negligence of Spinlock or its employees for
whom it is liable, the Service Centre indemnies and keeps indemnied Spinlock Ltd against
any claims demand proceedings liabilities damages or costs (including professional costs)
incurred by Spinlock directly or indirectly as a result of or in connection with any failure by it or
any of its employees or agents to comply with this Service Manual and the relevant service
training.
8. Save for death or personal injury caused by the negligence of Spinlock or its employees for
whom it is liable, Spinlock shall have no liability to any person, company or other organisation
whether in contract, tort, negligence breach of statutory duty or otherwise for any loss damage
harm costs or expenses of any nature whatsoever incurred or suffered by such person, company
or other organisation arising from or in connection with any error in or omission from this
Service Manual or the service training provided by it.
9. The contents of the Service Manual (including this notice) are governed in all respect by the
laws of England and the Service Centre or any other user of this Service Manual consent and
submit to the jurisdiction of the courts of England in respect of any dispute or matter arising
from or in connection with this Service Manual or the service training provided by Spinlock.
1
1 2
SHOULDER
FIT SYSTEM
INTEGRATES
WITH MOST
FALL ARREST
HARNESSES
2 x MK5i
FIRING
HEADS
ID / ASSET
TRACK
POCKET
FRONT OPENING
HEAVY-DUTY
BUCKLE (SOLAS)
DUAL
MANUAL
ACTIVATION
HANDLES
SPRAY
HOOD
PYLONTM
LIFEJACKET
LIGHT
FITTED
COMPATIBLE
WITH PRO-TECH
PROTECTIVE COVER
DUAL ORAL
INFLATION
TUBES &
WHISTLE
COVERED
QUICK-BURST
ZIP
EXTRA
DURABLE COVER
MATERIALS
HIGHLY
VISIBLE
RED LIFTING
STRAP
AIS
MOB1
UNIT
LUME-ONTM LIFEJACKET
ILLUMINATION
LIGHTS
SOFT LOOP
DECK HARNESS
ATTACHMENT POINT
WIDE
CROTCH
STRAP
NEW SOLAS+ WITH DECK HARNESS
ISO12402-1
INTEGRATED
DECK HARNESS
SMOOTH
BODY ADJUSTER
SYSTEM
2
Operations
Must be an established Lifejacket or Life-raft service station already or be approved by a relevant
National body or have the relevant experience.
Trained and qualied staff must be available to undertake training from a Spinlock representative.
Commit to give full contact details to Spinlock and ensure that they are registered in the service area of
www.spinlock.co.uk/service
Commit to checking Spinlock site for latest information once every 6 months and be available for
auditing at Spinlock’s request.
Jackets over 10 years old should not be serviced.
Facilities
Dedicated area and management system in place to manage the Service and record and le relevant
details.
Have the correct and calibrated tools. These can be ordered from Spinlock if required.
Torque driver Digital scales Adaptor
DW-SV1 DW-SV2 DW-SV3
Process
Follow servicing steps as outlined in this document or the latest copy available to down load from
www.spinlock.co.uk/service
Complete the service log on service label or on the internal label.
Complete service certicate with approval stamp.
More copies can be downloaded from www.spinlock.co.uk/service
Through Life Support Programme
Spinlock require all life jackets to be registered to benet from the security of our
Through Life Support Programme.
Please ensure customers register their Deckvests online at www.spinlock.co.uk/en/supports/register
Service Station Requirements
3
Check all stitching for signs of wear or damage:
Key stiching is in contrasting colours and located on the
front of the harness.
Obvious damage, contamination or loose theads will make
the harness unsafe.
Webbing:
Check for damage especially to the edge of the webbing
and ensure the buckles are not bent or damaged.
If the buckles are damaged the harness will need to be
replaced (contact Spinlock).
Servicing steps
1: Harness and cover
Materials:
Check all materials for obvious damage, general wear should not be a problem.
If the damage can not be repaired by a simple patch, then the cover will need to be replaced. If you
are concerned about the affect of the repair on the functionality of the Deckvest contact Spinlock.
Zip:
Open the jacket fully by the yellow break section on the zip.
Check internal sewing especially the connection points for the bladder.
Seperate the zip and run the slider back to the start on the opposite side.
If there is damage to the teeth of the zip then the cover will need to be replaced (contact Spinlock).
If the zip puller is damaged or missing, this can be replaced see section 7.
4
SOLAS +
Check Harness loop and bartacks on rear
2: Quick Burst Zip Information
5
A B C D
Start running zip back
round to close.
A BC D
Run slider round to
wearers right side.
A B CD
Re-attach zips.
Open zip at one
of the break
out points
A B C D
1
Deckvest Fitted with Ocean Signal MOB 1 AIS Device
6
1Thread ribbon end through oral tube bracket 2Thread back up through second hole towards outer edge
3Thread back through inside hole 4Leave 60mm on tail from end of plastic
5Slide toggle on to ribbon and pass ribbon through inside
hole on grey plastic activation slider 6Wrap round and pass through inside hole again
7Pass ribbon through outer hole 8Leave roughly 30mm of tail.
9Length of ribbon should measure between 27 - 30cm
27-30cm
10 Slide tail through toggle 11 Wind in antenna and attach activation slider to the MOB1
12 Place toggle into gap on slider and fold the tape back
over the toggle
13 Attach plastic cap to MOB 1 unit
Fitting kit supplied with MOB 1 or with part number DW-MOB/RELEASEKIT
For Spinlock DURO SOLAS Lifejacket (DW-SLS/A)
Fitting video available at www.spinlock.co.uk/aismob1 7
14 Slide whistle holder over oral tube, and then slide MOB 1 elastic
over the top.
15
16 Pass MOB 1 unit through elastic on oral tube 17 Attach the lanyard cord and pass the cord over and then
underneath the oral tube bracket
18 Attach the MOB1 Oral Tube bracket to the oral tube.
Check ribbon is not caught around cylinder, oral tube or whistle.
19 Secure MOB 1 cord to bladder toggle webbing to ensure unit
is always attached to Deckvest.
Cord should be placed above MOB 1 unit.
Fit O-Ring to
oral tube bracket
Note
When tting the beacon in the elastic
it can be simpler if elastic is removed
from oral tube rst, swapped around
so that the the wider hole can be used
for the beacon.
Note- Buddy line should be packed to the side
If the buddy strap is attached to this tube it can be
removed and placed in the folds of the lifejacket
20 Add MOB 1 rev 3 tted sticker inside the ID window.
Pass oral tube bracket and ribbon under cylinder between elastic
retainer and manifold. Ribbon should pass between cylinder and
retainer plastic as per picture B. Attach oral tube bracket MOB 1.
Ensure that this gives a direct lead for the release ribbon around
the jacket. For some older style jackets the ribbon will need to run
above the elastic to give a straighter direction of pull
B
Older models
Altri manuali per DURO SOLAS
1
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Spinlock Attrezzatura di sicurezza
Spinlock
Spinlock Deckvest 150N Manuale utente
Spinlock
Spinlock Deckvest DURO FC 170N Manuale utente
Spinlock
Spinlock 170N Manuale utente
Spinlock
Spinlock DECKVEST LITE Manuale utente
Spinlock
Spinlock deckvest 5D Manuale utente
Spinlock
Spinlock XAS Series Guida rapida
Spinlock
Spinlock deckware Series Manuale utente
Spinlock
Spinlock NEMO + Manuale utente
Spinlock
Spinlock DECK PRO Manuale utente
Spinlock
Spinlock MAST PRO Manuale utente
