Spitwater JETFIRE DI16 Istruzioni operative

Spitwater Australia pty Ltd

953 Metry St

North Albury, NSW

Australia

WARNING: Read and understand this instruction manual before operating this unit.

Retain this instruction booklet for future reference.

Failure to follow operating, safety and maintenance instructions outlined in this

manual releases the manufacturer from any responsibility for any accidents or

damages incurred and may render any warranty void

DIESEL / KEROSENE

FIRED HEATER

DI16

ORIGINAL INSTRUCTIONS

OPERATING AND MAINTENANCE

MANUAL

Made in

Korea for:

UNIT

BAR

Kg/H

V/~/Hz

HEATER

DI16

16.5

8.83

1.37

145

230/1/50

FUEL SUPPLY

Address

Phone number

550

340

570

HEIGHT

WEIGHT (without fuel)

The manufacturer reserves the right to modify designs, features and technical data without notice.

PERFORMANCE

FUEL

FUEL TANK CAPACITY

TECHNICAL DATA

PRODUCT

CONNECTED LOAD

LENGTH

WIDTH

MODEL

HEAT OUTPUT

PUMP PRESSURE

FUEL CONSUMPTION

MINIMUM ROOM VOLUME

Date of purchase

Business name

DIESEL & KEROSENE ONLY

ELECTRICAL

ELECTRICAL SUPPLY

DIMENSION & WEIGHT

The JETFIRE range of portable heaters are designed to give safe, efficient and reliable service

when the correct operating sequence are followed and proper attention is given to cleaning and

and maintenance procedures. This manual is to provide up to date information necessary to the user for

operating, cleaning and servicing the heaters, together with fault-finding techniques and general

specifications, details and diagrams. Please note that the information given herein after may be subject to

revision in compliance with the policy of continual improvements.

The JETFIRE range of heaters should only be used in the manner and purpose for which they were intended

and in accordance with the recommendations and safety precautions detailed in this manual and in

operating instructions and stickers on the unit itself.

All JETFIRE heaters undergo rigorous safety and operational tests before being despatched into the

marketplace however it is still imperative that prior to used, all operators have read and understood all

information and instructions provided and are aware of possible hazards.

The booklet contains important information for the use and safe operation of this heater. Please read and

all warnings before you start using the unit.

Spitwater has an extensive range of spare parts and accessories to suit all your heating needs.

For spare parts and service please contact 1800 SPITWATER

To view our extensive range of industrial heaters visit www.spitwater.com.au

The following symbols are used throughout this instruction booklet in order to mark important paragraphs

or sections that are due particular attention. Their meaning is listed next to them for your attention.

The following symbols are used on the machine in order to warn user of potential injury if not cautious.

Their meaning is listed next to them for your attention.

injury

Electric shock

Disconnect power

before removing

cover

Hot surface

WARNING

Do not touch,

will result in

WARNING

INTRODUCTION

GENERAL DESCRIPTION & INTENDED USE

SPARE PARTS AND ACCESSORIES

These are tips

WARNING

result in injury

or death

Failure to follow

instruction could

result in damage

to machine

instruction could

and instructions

to ensure safe

and proper

operation

Failure to follow

WARNING: This heater shall only be used by persons instructed in its use that have been

been expressly authorized to do so. Before using this heater please pay particular attention

to the following safety warnings as failure to do so could result in serious injury.

1 Make sure you have read and understood the whole instruction manual before installing,

operating or carrying out any maintenance on the unit.

2 Warnings and data plates on the machine provide important directions and information

on the safe use of the unit.

3 Besides these operating and safety instructions please make sure that all accident

prevention regulations applicable in the country of use are followed.

4 As well as these operating and safety instructions any standards relating to the

installation and operation of industrial heaters applicable in your country must be

strictly followed.

1 For safe moving of the unit between work areas make sure that the unit has been

switched off and is allowed to cool if necessary.

2 Lift from handle of the machine.

3 For safe transport in and on vehicles make sure the machine is appropriately strapped

in order to avoid it sliding or falling.

1GENERAL

- The heater unit must be positioned on flat stable ground and must be in an upright

position before operating. Do not operate on uneven surface or loose gravel.

- The heater unit must be checked that it is safe and in proper working order before

putting into service and before every use. If the unit is damaged do not use it.

- The heating space must be properly ventilated in compliance with this manual and the

heater unit must be serviced as per maintenance guidelines in this manual to avoid

carbon monoxide build up, which can lead to death.

SAFETY INSTRUCTIONS & PRECAUTIONS

IMPORTANT SAFETY INSTRUCTIONS

AND PRECAUTIONS

GENERAL WARNING

TRANSPORT

2WHILE USING THE HEATER

- Read all instructions before using this heater take care to ensure you fully understand

the instructions concerning electricity and fuel supply.

- Know how to start and stop the unit. Be quite familiar with the controls.

- Allow a minimum room size as listed in the technical specifications.

- Not for domestic use, space heating only.

- Local regulations should be followed as to the installation of industrial heaters.

- Do not operate the heater if it is damaged.

- Never leave the heater unattended whilst running.

- Permanent ventilation to the outside atmosphere must be provided. Allow 96 sq.cm for

every 1000W input divided equally between floor and high levels.

- Do not operate this heater in basements or below ground.

- Do not restrict under any circumstances either the inlet or outlet end of the heater.

- The heater must not be used in close proximity to combustible or flammable materials.

- The heater must operate in a space with clearance of 1m above and behind and 600mm

on the sides. A guard must be placed 900mm away from the heater outlet to prevent the

approach of combustible materials.

- Always use the handle to move the heater after it has been operating as other parts of

the heater may be very hot.

Use only clean filtered diesel or kerosene as fuel. Do not refill the fuel tank while the

heater is running or is still hot.

- Follow the maintenance procedures and fault-finding techniques outlined in the manual.

- To prevent injury always disconnect the power plug before disassembling any part of the

heater.

- Do not carry out temporary repairs on worn or damaged electrical cords and plugs.

- Have worn, cut or damaged cords and plugs replaced by an authorised service person or

electrician.

- Do not pull on the electrical cord in order to unplug the unit.

- Do not use this heater in the rain or when it is at risk of being sprayed with water.

3ELECTRICITY SUPPLY

The JETFIRE range of heaters is designed to run off 230V Single-Phase 50Hz electrical

supply. The unit should be plugged into a 10A outlet.

- The appliances must be earthed.

- If the Plug needs to be replaced to suit local requirements a qualified electrician should

carry out the replacement taking care to earth the unit and maintain the correct phase

connection as per the wiring diagram.

4FUEL SUPPLY

- Please only use the following fuel types in the heater:

Kerosene with viscosity of 1.3 cSt or Diesel with viscosity of 1.5 cSt.

Temperature Limit Control :

This heater is equipped with a Temperature Limit Control designed to turn off the

heater should the internal temperature rise to an unsafe level. If this device activates

and turns your heater off it may require service.

(Internal Shut-Off Temperature - 212˚F/100˚C ± 10°, Reset Temperature - 176˚F/80˚C ± 10°)

Electrical System Protection :

The heater's electrical system is protected by a fuse mounted to the PCB assembly that

protects the system components from damage. If the heater fails, check the fuse first,

and replace if necessary.

Flame-Out Sensor

The heater uses photocell to see the flame in the combustion chamber. Should the flame

extinguish, the sensor will stop electrical current and the heater will shut off.

Shock(earthquake) automatic shut-off Device

This Heater is equipped with Tip Over switch, In case that earthquake more than 5 magnitude

happens or that heater inclined 5 ~ 10°. Heater will be shut-off by Tip Over switch for safety.

(Refer to Trouble Shooting )

1 Carry out all regular maintenance and inspections as listed in this manual using original

JETFIRE parts where required.

2 Always make sure before carrying out any maintenance that the unit is turned off and

allowed to cool down.

3 Always make sure to disconnect the power plug from the mains outlet before carrying

out any maintenance work on the unit.

4 Never carry out any maintenance work not expressly outlined in this booklet and never

make any technical modifications to this unit.

This unit is fitted with safety devices which are set and sealed at the factory. It is very

important these devices receive their routine maintenance to assure your safety as well

as necessary protection of the unit.

6 There are a number of very important components that have been set and sealed at the

factory. Never under any circumstances tamper with, modify or adjust these settings.

7 Make sure this unit is regularly serviced by an authorized JETFIRE agent according to the

servicing requirement outlined in this booklet.

8 Always dispose of unused fuel according to requirements of the local authorities.

SAFETY DEVICES

MAINTENANCE & SERVICING

OPERATING ELEMENTS

Please see operating elements below to help familiarize yourself with the components of this unit.

Figure B

Figure A

Figure G

Figure H

1 Take the heater out of the box and remove the handle from heater. (Figure A)

2 Remove the pre-assembled screws on the shell.

3 Align the holes in the shell with two mounting holes on the handle as shown in Figure B.

4 Secure handle with screws with removed.

Save the shipping carton and packing materials for future storage.

To Start (Normal Operation)

1 Fill the tank with kerosene / diesel until fuel gauge points to "F".

2 Be sure fuel cap is secure.

3 Plug power cord into 230V power outlet. (Figure G)

Turn “Thermostat Control Knob” to desired setting (setting range : 0℃~40℃)

and push operating switch to “ON” position (Figure H), power

indicator lamp and room temp. display will light and heater will start.

NOTE

- The extension cord should be at least six feet long.

- Extension cord wire size requirements are as follows:

6 to 10 feet (1.8 to 3 meters ), use 18 AWG wire.

11 to100 feet (3.4 to 30.4 meters ), use 16 AWG wire.

101 to 200 feet (30.8 to 61 meters), use 14 AWG wire.

To Stop (Normal Operation)

Turn the Operating Switch to "OFF" position. Combustion will stop, and the cooling cycle

will begin (Dur. -7 mins). (Room Temp. Display will show "CC" during the cooling cycle)

When cooling Cycle is completed (fan stops running), it is safe to unplug the heater.

NOTE

- Unplugging the heater before the Cooling Cycle has ended may cause overheating,

damage to the heater, and could void the warranty.

When the heater is not going to be used for a long period it is to be stored in accordance with the steps shown below.

1 Unscrew Fuel Cap and using an approved kerosene siphon, remove kerosene / diesel.

2 Using a small amount of kerosene, rinse and swirl the kerosene inside of the Fuel Tank.

3 Empty the tank fully.

4 Replace the fuel cap.

5 Repack the unit in original shipping material and store in area free of dust and corrosive vapours.

ASSEMBLY, INSTALLATION AND

OPERATING INSTRUCTIONS

ASSEMBLY

OPERATING INSTRUCTIONS

LONG TERM STORAGE

To maintain this unit in peak working condition during its operating life it is necessary to carry out regular

maintenance operations and replace worn or broken parts immediately upon their failure. We strongly advise

that all maintenance is carried out by an authorized JETFIRE agent using original spare parts.

Failure to follow the maintenance guidelines in this booklet releases the manufacturer from

any responsibility in reference to injuries and damages to both persons and goods.

This also may render any warranty given with the unit void.

General

1 Power cable (Each use)

- Check the power cable / plug for any cuts, abrasions or damage before each use. If damage is

found it must be replaced immediately (Not repaired) by an authorized service

person / electrician.

2 Fuel connections (Each use)

- Check fuel fittings and connections for leaks.

3 Performance (Each use)

- Check machine functionality to ensure it is operating as normal.

- Check the units performance characteristics as specified in technical data.

Should any issue be found contact an authorized JETFIRE agent immediately for repair.

Note

ALWAYS ISOLATE UNIT FROM THE ELECTRICAL SUPPLY BEFORE ATTEMPTING ANY REPAIRS

OR MAINTENANCE.

Replacing Pump Fuel Filter. (Figure K)

1 Unscrew(C.W) Filter bottom from Filter top with adjustable pliers. (Figure J)

2 Remove Filter from Filter top

3 Wash Filter in clean kerosene and Remove Dirt.

4 Put Filter back in Filter Top. and Tighten Filter bottom firmly.

5 Reinstall Back Cover.

Replacing Fuel Filter in Fuel Tank. (Figure J)

1 Pull fuel line off from Fuel Filter neck

2 Carefully Pull fuel filter off from Fuel tank with hand or flat blade screwdriver.

3 Wash Filter with clean Kerosene and replace in tank and attach fuel line to fuel filter neck.

Figure J Figure K

MAINTENANCE INSTRUCTIONS

AND TROUBLESHOOTING

MAINTENANCE INSTRUCTIONS

Indice

Altri manuali Spitwater Stufa

Spitwater

Spitwater JETFIRE J20A Istruzioni operative

Spitwater

Spitwater JETFIRE IP110 Istruzioni operative

Spitwater

Spitwater IC 25 SPITFIRE Manuale di installazione e funzionamento

Spitwater

Spitwater SHW11 Istruzioni operative

Spitwater

Spitwater JETFIRE DP65 Istruzioni operative

Manuali Stufa popolari di altre marche

oventrop

oventrop Regucor Series Manuale utente

Blaze King

Blaze King CLARITY CL2118.IPI.1 Manuale utente

ELMEKO

ELMEKO ML 150 Manuale utente

BN Thermic

BN Thermic 830T Manuale utente

KING

KING K Series Guida

Empire Comfort Systems

Empire Comfort Systems RH-50-5 Guida rapida

Well Straler

Well Straler RC-16B Manuale utente

EUROM

EUROM 333299 Manuale utente

Heylo

Heylo K 170 Manuale utente

Eterna

Eterna TR70W Manuale utente

Clarke

Clarke GRH15 Manuale di istruzioni

IRSAP

IRSAP The Radiator Company Ovali Manuale utente

Empire Heating Systems

Empire Heating Systems WCC65 Manuale utente

Wetekom

Wetekom 92 86 43 Manuale utente

Desa

Desa SPC170-F Manuale utente

Watlow

Watlow Watrod Electric Tubular Heaters Manuale utente

Haverland

Haverland ECO-DRY GPS Series Manuale elenco delle parti

Stelpro

Stelpro ASILVC2060 Series Manuale utente