SpotLine SpotLine M110 Manuale utente
SpotLine TM M110
User Guide
2
SpotLine M110 User Guide
All Rights Reserved. This document, as well as the software and data
described in it, is furnished under license and may only be used or
copied in accordance with the terms of the license.
Except as permitted by such license, no part of this document may be
reproduced, stored in a retrieval system, or transmitted, in any form, or
by any means, electronic, mechanical, optical, recording or otherwise,
without the prior written permission of SpotLine Inc.
SpotLine and SpotLine M110 are Trademarks of SpotLine Inc.
The information in this document is furnished for informational
purposes only, is subject to change without notice, and should not be
construed as a commitment by SpotLine Inc., who assumes no liability
for any errors or inaccuracies that may appear in this document.
SpotLine Inc.
1131 Grandview Dr.
So. San Francisco
CA 94080
(650) 583-9605
(650) 583-9608 (fax)
© Copyright 2002 SpotLine Inc.
3
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This equipment had been tested and found to comply with the limits for
a class B digital device pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and
receiver.
-Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
-Consult an experienced radio/TV technician.
Caution to the user: The Federal Communications Commission warns
the users that changes or modifications of the unit not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
4
SpotLine M110 User Guide
Table of Contents
1.0 Introduction...................................................................................6
2.0 Specifications................................................................................8
3.0 Getting Started...........................................................................10
3.1 Installation............................................................................................................... 10
3.2 Setup........................................................................................................................ 11
4.0 Usage.........................................................................................12
4.1 Configuration Setup ................................................................................................ 12
4.1.1 User Environment ............................................................................................ 13
4.1.2 Port Configuration........................................................................................... 16
4.1.3 Sessions ............................................................................................................ 19
4.1.3.a Term: ......................................................................................................... 21
4.1.4 Network Parameters......................................................................................... 22
4.1.4.a Print Server:............................................................................................... 24
4.1.4.b Print Screen:.............................................................................................. 25
4.1.5 Host Name........................................................................................................ 26
4.1.8 Exit without Saving.......................................................................................... 27
4.2 Reverse Telnet......................................................................................................... 28
4.3 Remote TTY for Unix Systems .............................................................................. 30
4.4 Reversal of the LED’s for Num. Lock and Caps .................................................... 32
Lock .............................................................................................................................. 32
4.5 Purge the Printer Buffer .......................................................................................... 32
4.6 Function Key........................................................................................................... 33
4.6.1 Function Key Reset.......................................................................................... 33
4.6.2 Programming function keys (F1-F24) ............................................................ 33
4.7 Multiscreen Session Switching............................................................................... 35
4.7.1 How to declare SCO mscreen for SpotLine Terminals ................................... 35
4.8 Telnet Session......................................................................................................... 36
5.0 Software Configuration..............................................................38
5.1 SCO XENIX/Unix .................................................................................................. 38
5.1.1 Use as a Telnet Session LAN Terminal........................................................... 38
5.1.2 Setting up the LAN Terminal for Printing....................................................... 38
5.1.3 Use as a Serial Terminal.................................................................................. 40
5.2 Use with IBM’s AIX Unix...................................................................................... 41
5.2.1 Use as a Serial AIX Terminal Device.............................................................. 41
5.2.2 Use as a Telnet terminal................................................................................... 41
5.3 Other Unix Versions ............................................................................................... 43
5.3.1 Use as a Serial Terminal.................................................................................. 43
5.4 Use with Other Operating Systems ......................................................................... 44
6.0 Cabling.......................................................................................45
5
6.1 Terminal to Host Cabling........................................................................................ 45
6.2 Serial Printer Cabling.............................................................................................. 46
7.0 Emulation..................................................................................47
7.1 General.................................................................................................................... 47
7.2 Keyboard Control Characters.................................................................................. 47
7.3 Screen Control Parameters...................................................................................... 49
7.4 Local Printer Control Codes -ANSI and AT386.................................................... 51
Emulation...................................................................................................................... 51
7.5 Additional ESC Commands.................................................................................... 52
8.0 Warranty.....................................................................................54
6
1.0 Introduction
The SpotLine M110 is part of a new generation of
asynchronous/LAN terminals designed for all multi-user environments,
from microcomputers to minis to mainframes.
And why is this concept new?
It is new and original because the SpotLine M110 demonstrates
six key characteristics: Color, Performance, Expandability, Intelligence,
Standardization and Integration.
Color: The color can be controlled completely by the host
computer, with the application program setting whatever it wants.
Performance: Thanks to the high communication speed (up to
115Kbaud) with the host server, the response time for your application
is greatly improved.
Expandability: The expandability of the SpotLine M110
terminal is based on two factors:
-Any base unit can be upgraded from monochrome to color simply
by changing the monitor you use.
-All the logic and control hardware reside in a separate small unit,
which can then be upgraded for future generations more quickly
than building the old style of all-in-one terminal.
Intelligence: The built-in functionality of the SpotLine M110
relieves the host computer of many communications tasks, and
allows for many different configurations.
In addition, the SpotLine’s multiple ports, windowing and multisession
capability allows the simultaneous connection to more than one host
machine, even if they are running different operating systems.
7
Standardization: The SpotLine M110 is designed to work
with industry standard keyboards, monitors and printers, enabling
simple replacement and maintenance of any component.
Integration: The SpotLine M110 has been designed for
fast, friendly and simple setup, allowing for immediate and easy
integration with your host computer. The resulting system will then use
homogenous peripherals, monitors and keyboards.
8
1.0 Specifications
The principal characteristics of the SpotLine M110 are:
EMULATION: The SpotLine M110 has a number of built-in
emulation modes designed to fully support the demands of the
principal multi-user operating systems available in the marketplace.
Emulations include SCO/ANSI, Pcterm, IBM 3151, DEC VT family,
and others.
LAN: The SpotLine M110 uses industry standard
Ethernet TCP/IP to provide:
-ARP/ICMP/IP/TCP/UDP/Telnet/LPR services.
-Up to 8 simultaneous Telnet sessions
-Connection to Ethernet via 10Base2 (ThinNet) using a standard
BNC connector, or 10BaseT cabling (RJ-45 UTP), with dynamic
recognition of which connector you are using.
SPEED: The SpotLine M110 terminal can also
connect to any RS232C serial port and communicate asynchronously
with host computers at any speed from 1200 baud to 115K baud. Serial
and LAN sessions can be active at the same time.
MONITORS: You may connect any monochrome or color
VGA/SuperVGA monitor to the SpotLine M110. If you use
monochrome, it will automatically be detected and color values will be
automatically translated to various brightness levels.
KEYBOARDS: The SpotLine M110 has a PC/AT
compatible keyboard port, and can be used with both international scan
code keyboards and ASCII keyboards.
9
PARALLEL PRINTER: The parallel printer port supports a local
printer off the terminal. The buffer allows for the rapid transmission of
data from the host computer. Printers may then be used as local or
system wide devices.
SERIAL PRINTER: A serial printer may be connected to the
Serial 1 or Serial 2 ports, or both, on the SpotLine M110. The
buffer for print functions allows for efficient use of the chosen port, and
printers may then be local or system wide resources.
10
2.0 Getting Started
3.1 Installation
Follow these steps to install your SpotLine M110:
vConnect a VGA monitor to the monitor port.
vConnect your chosen keyboard
vConnect your terminal to the host server via the LAN using RJ-45
UTP Ethernet, if you wish to use it as a TCP/IP terminal. There are no
switches to set. The terminal will automatically detect which connector you
have used.
vConnect a suitable cable to either the SERIAL 1 or SERIAL 2 RS-
232 connectors, and the primary/other server for the terminal. See
Chapter 6 for the necessary cabling diagrams.
vConnect a suitable cable to the other serial port and another server if
so desired.
vAttach a parallel printer to the parallel port if needed.
vConnect a serial printer to the unused serial port if needed.
Indice
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
