Spotwave SpotCell2104Xf Manuale utente

SpotCell2104Xf

SpotCell3104Xf

Digital Repeater

User’s Manual

Digital Repeater User Manual

- 2 -

1Safety Warnings_____________________________________________________________________ 3

2Why repeater________________________________________________________________________ 4

2.1 Reason 1 ________________________________________________________________4

2.2 Reason 2 ________________________________________________________________4

3Introduction_________________________________________________________________________ 6

4System Characteristics ______________________________________________________________ 7

4.1 Features _________________________________________________________________7

4.2 Appearance of DIGITAL repeaters _____________________________________________7

5Block diagram and work principle ____________________________________________________ 7

6The repeater system_________________________________________________________________ 9

7Installation_________________________________________________________________________ 99

7.1 Installation Location Requirement____________________________________________100

7.2 Power requirement _______________________________________________________100

7.3 Installation tools and accessories____________________________________________100

7.4 Installation of donor antenna________________________________________________100

7.5 Indoor antenna installation _________________________________________________155

7.6 Repeater Installation______________________________________________________177

Installation Steps_____________________________________________________________17

7.6.2 Repeater’s ports description ________________________________________________________ 17

7.6.3 Accessories selection ____________________________________________________________ 1919

7.7 Repater Settings 20

7.7.1 Switch on power __________________________________________________________________ 190

7.7.2 Manual Gain Control (MGC)_______________________________________________________ 200

7.7.3 Frequency Setting ________________________________________________________________ 211

7.7.4 Repeater Commissioning 21

7.8 System Test ____________________________________________________________233

7.8.1 Check whether the coverage is good_______________________________________________ 233

7.8.2 Repeater can not communicate in Power-ON status __________________________244

8Maintenance ______________________________________________________________________ 255

8.1 Routine maintenance 25

8.2 Troubleshooting _________________________________________________________255

9 IC STATEMENT

Error! Bookmark not defined.6

10 IC Radiation Exposure Statement 27

11 Technical Parameters 27

12 FCC RF Exposure Statement_______________________________________________28

Digital Repeater User Manual

- 3 -

Preface

This user’s manual describes the installation, commissioning and maintenance of digital

repeaters.

Please do read the user manual carefully before installing and maintaining digital repeaters.

The information in this manual is subject to change without prior notice.

Opinions are welcomed about the manual improvement.

1 Safety Warnings

Users must follow the below principles：

Repeater should follow system requirement of communication equipment, assure good

groundings and lightning protection.

The power supply voltage of repeater should meet the standards of security requirement; any

operation shall be carried out only after cutting off power in advance. Only the professional is

authorized for the operation.

Do not dismantle machine, maintain or displace accessories by yourself, because in

this way, the equipment may be damaged or even get an electric shock.

Do not open the repeater; touch the module of repeater, or to open the cover of module to

touch the electronic component, the components will be damaged due to electrostatic.

Please keep away from heating-equipment, because the repeater will dissipate heat during

operation.And do not cover booster with anything that influences heat-dissipation.

Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries

according to the instructions.

Digital Repeater User Manual

- 4 -

WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC

LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express

consent of an FCC licensee to operate this device. Unauthorized use may result in significant

forfeiture penalties, including penalties in excess of ＄100,100 for each continuing violation.

WARNING. For antenna and accessories, there are many brand or similar items, if clients

need to use such items, please compare the specifications carefully and consult the

professional manufacture if it’s suitable to use. The usage of the unqualified antennas,

cables or coupling device may result in the improper work of boosters and even damage

the device. Please double check before changing these items.

2 Why repeater

2.1 Reason 1

1) Blind or weak signal areas are formed if the buildings are too far away from BTS, or the buildings

themselves shield or absorb the signals.

2) There are too many complicated signals in the higher part of the buildings, therefore ping-pong switching

effect has been formed and the signals fluctuate a lot, there are annoying noises during phone calls and

there are dropped phone calls accordingly.

3) Elevators and basements are well-known blind areas.

4) Downtown areas of the cities, congested with many high-rise buildings are usually the weak or blind

areas.

2.2 Reason 2

The remote villages, mountains, hills, valleys, etc are mostly scarcely populated areas with quite few mobile

users, so the main target is to send coverage to these areas, and it will not be cost effect to install a BTS tower,

therefore a booster is a quite good option.

Can we not use mobile phones? The answer is definitely NO. But it might be much more miserable that the

Digital Repeater User Manual

- 5 -

communication can’t be achieved due to no or weak signals though there is a mobile phone.

Will your customers stay comfortable when there is no smooth communication in your shops or restaurants?

Will your business be influenced if your clients couldn’t call you through due to weak signals in offices?

Will your life be influenced if your mobile is always “out of service” at home when your friends call you?

How to solve the problems?

Best Solution:

Plug & play: Purchase a set of booster solution and install it at your home, offices, and

plug on the power and immediately you would be able to enjoy the full bar and high quality

signals!

Question: Will booster increase the RF radiation?

A: No, it will decrease instead.

As it can be searched easily through internet, the tower would “order” the mobile phone to increase its output

power, in order to ensure successful connection when the mobile signal bar is few, there will be stronger mobile

output power level when the mobile signal bar is less and the strongest one can reach 2W (GSM); moreover,

the mobile phone is usually as near as less than 5cm to human body when people are in phone calls. Not only

it influences badly the human bodies, but also run out of the battery power much more quickly; usually the

mobile phone gets hot in such status.

The maximum power level of digital repeater is 0.2W, and it decreases to be maximum 0.006W when reaching

server antenna.And since the server antenna is installed over the ceiling or onto the wall, there is usually more

than 3 meter away from the human body, 3meter away means at least 40dB propagation loss, or 10000 times

less, 0.0000006W, and therefore it is too weak to influence human bodies though it is still a very good signal for

mobile phones.

And when a booster is installed, it improves the mobile signals in the coverage, and the successful phone call

can be connected easily with a much less power level of the mobile phone, thus it will reduce tremendously the

RF radiation.

Digital Repeater User Manual

- 6 -

3 Introduction

Digital repeater full duplex mobile communications repeater is the perfect solution for providing a wireless

improvement in the cellular reception of a home, office, restaurant, VIP Room, apartment, building or shopping

mall, in the quickest time possible. One repeater covers 2000 to 2500 square meters.

It is designed to improve the call quality of an area by receiving, amplifying and re-transmitting signals of the

base station into a specified area via the server antenna of the repeater.

This repeater has Manual Gain Control (MGC) feature that enables engineers to reduce the gain of the repeater

manually if oscillation is detected or too strong input power level during installation, this will help to get the best

coverage effect without any interference back to mobile network.

And to maintain safe and specific output signal levels during the repeater’s operation, this repeater has a built-in

signal oscillation detection circuit to adjust the gain automatically so as to avoid interference to the cellular

network, also it gets color changing LED’s indicate its environmental status: the Alarm LED’s located inside the

housing of the unit will change color from OFF to red, (depending on the input power level) if the system detects

signal oscillation in either band or, if the input signal is beyond a safe limit.

Below diagram shows how simple and fast digital repeater system is installed and works effectively.

One donor antenna, has been installed at the top of the roof to pick up good mobile signals from outside, and

send through a 5D-FB cable to a digital repeater to be amplified significantly, then the output signals are divided

into two signals by a 2way splitter, sent to two indoor omni antennas and finally transmitted into the coverage

area. Very clear phone call or high speed mobile data services are immediately affected within the area.

Digital Repeater User Manual

- 7 -

4 System Characteristics

4.1 Features

Excellent out of band rejection

Wide power supply range and low power consumption

High-integration (One board to contain low-noise amplifier, frequency selection module, power

amplifier module)

Manual gain control provides a variety of applications

Support multi-system, multi-band, band selectable and adjustable

4.2 Appearance of DIGITAL repeaters

Figure 1 the front view (colors may differ from real products).

5 Block diagram and work principle

Digital repeater is basically a bi-directional amplifier, the downlink signals are received by the repeater from

BTS by the donor antenna, filtered by its internal duplexers and FPGA module, amplified by low noise amplifier

Digital Repeater User Manual

- 8 -

(LNA) and downlink PA unit, and then sent via the server antenna to the coverage area. The bandwidth is

operators’working frequency only.

The uplink signal of mobile terminal from the coverage area is input via the server antenna, then filtered by

duplexers and FPGA module, amplified by the uplink low noise amplifier (LNA) and the uplink PA unit and finally

sent via the donor antenna to the BTS.

Modules in the system diagram:

Combiner：The main purpose of combiner is to combine two system to share the same antennas.

Duplexer: The main purpose of duplexer is to combine downlink and uplink to share the same

antennas, the duplexer is composted of one pair of band pass filter that can not only reject the

spurious interference, but also increase the isolation of Uplink and Downlink.

LNA: LNA is the first active sub system of the repeater, of which low noise and high linearity is

requested under strong input signals. LNA is the major sub system that determines the noise figure

of the repeater system.

FPGA: Field－Programmable Gate Array, FPGA module is to process the digital signal transferred

from analog signal and filter the signal out of selective band.

PA: The power amplifier sub system helps the repeater to reach its targeted output power, linearity

of which decides the linearity of the repeater.

Power supply is to supply power electricity to all repeaters’ modules.

Digital Repeater User Manual

- 9 -

6 The repeater system

Donor Antenna：

5~7dbi outdoor panel or 7~9dBi wide band Yagi are recommended as donor antenna.

Function: Pick up donor signals from the BTS and send to the repeater by cable; the received

signals’power level and quality influence a lot on the coverage effect. Donor antenna also

transmits the uplink signals from the repeater to BTS.

Server Antenna:

2~3dBi indoor omni ceiling or 5~7dBi indoor panel are recommended.

Omni antenna (Indoor ceiling omni antenna or whip antenna), suitable to installed in the center

and radiate all direction; It is better to use a directional panel antenna or Yagi when the coverage

shape is long and narrow (corridors, long row of houses in two sides, tunnels or elevators or rural

open space).

Cables: LMR 300 or 400, 5D or 8D –FB coax cables are recommended.

Splitters or couplers: when the building structure is too complicated or there is big loss due to thick

walls, etc., splitters or couplers shall be used so that more antennas can be installed in more areas

to distribute the signals to each corner of the coverage area.

Power Box including electricity meter, air switch and groundings, some sites might need surge

arrestors.

7 Installation

Digital repeater should be used to cover the area indoor and the humidity and temperature of working can affect the

reliability of repeater. So, temperature, humidity, dust, interference, power, space requirements and other factors

should be considered during installation of repeater.

Digital Repeater User Manual

- 10 -

7.1 Installation Location Requirement

1) It is appreciated that the repeater is installed in a cool, dry and ventilated room without erosive gas and

smoke and without leakage on its proof.

2) Besides above, a cool and ventilated wall of which sun-proof and waterproof is expected.

3) Besides above, common wall, tower or high pole is ok.

4) Installation height should be easy for RF cable wiring, heat dissipation, security and maintenance.

5) Have a set of independent and stable power supply.

6) Have lightning conducer in the building, tower or high pole with enough strength or stability.

7.2 Power requirement

Generally it is AC power supply, and the requirement ofAC is 100~264VAC/55±5Hz.

7.3 Installation tools and accessories

No.

Name

Specification

Quantity

Remark

Expansion screw

M10*100

Standard accessories

Expansion screw

M6*35

Standard accessories

Grounding screw

M6*22

Standard accessories

reciprocating drill

Engineering-owned, punch the

wall

Shot bit

Engineering-owned, punch the

wall

Recommend Splitter:

Frequency(MHz)

1710-1990

2110-2170

Splitter

2-Way Splitter

-3.6

-3.8

3-Way Splitter

-5.2

-5.4

7.4 Installation of donor antenna

The repeater’s main function is to improve weak RF signals to an area. A simple formula: Input power+ Gain=

Output power. The signal strength from the outdoor antenna directly affects the efficiency of the indoor coverage.

It is very important to choose the location of the outdoor antenna carefully. With this in mind, it is not

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Spotwave Ripetitore

Spotwave

Spotwave SpotCell Coverage Extension Kit Manuale utente

Spotwave

Spotwave spotcell 100 Manuale utente

Manuali Ripetitore popolari di altre marche

Gigaset

Gigaset 108 Manuale utente

Ace TECHNOLOGY

Ace TECHNOLOGY USR-1900A Manuale utente

Kenwood

Kenwood TKR-750-850 Manuale elenco delle parti

Asus

Asus RP-AC51 Manuale utente

Exibel

Exibel HRP0101 Manuale utente

Kidde

Kidde Vega Manuale utente

Telcosat

Telcosat RBB 850 Guida all'installazione

York

York Universal LINC485 Manuale utente

MIKOM

MIKOM MRx01B Power Series Manuale utente

Simrad

Simrad RD 301 Manuale utente

Tait

Tait TB7304 Manuale utente

R-tron

R-tron RSN-CDMA-37-C Manuale utente

Inventronics

Inventronics DALI REPEATER SO Manuale utente

XFP

XFP 16 Manuale utente

Andrew

Andrew MRx18 Manuale utente

COMBA

COMBA RXA3748 Manuale utente

ADRF

ADRF SDR-ICS-43 Manuale utente

Teltonika

Teltonika WRP100 Manuale utente