SPT Plasmateknik AB SPLITFIRE Manuale utente

INSTRUCTIONS FOR USE

SPLITFIRE

SPEEDFIRE

UPPERCUT

With PTA 121 hand torch

TO THE OPERATOR: PLEASE READ AND UNDERSTAND THIS MANUAL

BEFORE USING THE SPLITFIRE, SPEEDFIRE OR UPPERCUT. IT IS

ABSOLUTELY VITAL TO KNOW THE INFORMATION PRESENTED IN THIS

MANUAL IN ORDER TO USE THE MACHINES IN THE BEST WAY.

WITH THIS KNOWLEDGE AND A PROFESSIONAL APPROACH, YOU WILL BE

ABLE TO SOLVE MANY COMPLICATED CUTTING APPLICATIONS WITH THESE

SYSTEMS.

Rev. 4.2, 2012-11-01

STATE OF THE ARC PLASMA CUTTING TECHNOLOGY

Telephone

SPT Plasmateknik AB

Transportvägen12

SE-241 38 Eslöv

Sweden

Internet

+46 10-172 73 50

[email protected]

www.spt.se

SPLITFIRE SPEEDFIRE UPPERCUT

CONTENTS

Page

1. TECHNICAL DATA 3

2. INSTALLATION 4

3. OPERATING INSTRUCTIONS 5

4. CHANGING CONSUMABLES 6

5. MAINTENANCE 8

6. TROUBLE SHOOTING 9

7. SAFETY INSTRUCTIONS 10

8. WARRANTY 14

9. RECYCLING 15

SPLITFIRE SPEEDFIRE UPPERCUT

1. TECHNICAL DATA

UPPERCUT

Power supply 400 V, 3~50 Hz

Mains fuse 32 A slow blow

Maximum power 17,6 kVA

Process power 120 V, 20-120 A

Duty cycle @ 40°C 30% @ 120 A

60% @ 100 A

100% @ 80 A

Power factor

Open circuit voltage

Protection class

Cooling

Temperature class

Dimensions LxWxH

Weight

0,95

240 VDC

IP 23

560x190x320

18kg

Maximum cutting capacity

Quality cut

Air pressure

45 mm

35 mm

5,5 bar

Air flow PTA 121 190 l/min

Standard torch length

SPLITFIRE

400 V, 3~50 Hz

16 A slow blow

10,4 kVA

120 V, 20-80 A

50% @ 80 A

60% @ 60 A

100 % @ 45 A

0,95

240 VDC

IP 23

560x190x320

17kg

25mm

20 mm

4,5 bar

160 l/min

6 m

SPEEDFIRE

400 V, 3~50 Hz

32 A slow blow

14,5 kVA

120 V, 20-100 A

40% @ 100 A

60% @ 80 A

100% @ 70 A

0,95

240 VDC

IP 23

560x190x320

17kg

35 mm

30 mm

5,5 bar

190 l/min

6 m 6 m

SPLITFIRE SPEEDFIRE UPPERCUT

2. INSTALLATION

Connect the torch to the power source. After connecting electric power and compressed

air, the machine is ready for use. Please read the enclosed instructions on how to use the

central connector.

Power supply

Connect the machine to 3-Phase, 50 Hz, 400 V only.

Use with generators

SPLITFIRE, SPEEDFIRE and UPPERCUT are equipped with filters for use with mobile

generators. The generator should be of at least 15 kVA for SPLITFIRE, 22 kVA for

SPEEDFIRE and 27 kVA available exclusively for the plasma cutting system.

Air supply

Connect dry, clean and oil free compressed air to the filter regulator on the rear of the

machine and adjust to 4,5 bar for SPLITFIRE and 5 bar for SPEEDFIRE/UPPERCUT. When

cutting at lower amperage than 70 A with SPEEDFIRE/UPPERCUT it may be necessary to

lower the air pressure to 4,5 bar in order to get the best cutting capability. Don’t forget to raise

the pressure again if returning to amperage above 70 A.

SPLITFIRE SPEEDFIRE UPPERCUT

3. OPERATING INSTRUCTIONS

Check that the machine has been properly connected to power supply and compressed air

according to chapter 2, INSTALLATION.

Check that the torch is fitted with appropriate consumables for the job at hand.

Connect the earth lead clamp directly at the work piece, ensuring that a good contact is

obtained. If necessary, clean the surface from paint, rust, dirt, etc.

Cutting

Switch the machine’s main power switch on. The READY lamp will light and the fan

will start working.

Choose process power, 20-80 for SPLITFIRE, 20-100 A for SPEEDFIRE or 20-120 A

for UPPERCUT.

Manouver the torch in position for cutting or gouging.

Press the START-switch on the torch handle.

Air will flow for one second before the pilot arc strikes. The pilot arc will burn for

about 3 seconds. If contact with the work piece is not obtanined within this time, the

pilot arc goes out. Then make a new try.

To end the process, release the START-switch. The plasma arc goes out

instantaneously. Air will continue to flow for about 30 seconds.

NOTE! When the machine is not in use or is only working at long intervals, switch off

the machine. It contains mechanical components that should not be exposed to unnecessary

wear. It also protects against unvoluntarily firing the pilot arc.

SPLITFIRE SPEEDFIRE UPPERCUT

4. CHANGING CONSUMABLES

SPLITFIRE SPEEDFIRE UPPERCUT

Consumables/torchparts for PTA 120/121

Part No. Description

899044 Torch head PTA 121

899003 Electrode standard PTA 120/121

899017 Electrode long PTA 120/121

899004 Swirl ring PTA 120/121 for 20-80 A

899023 Swirl ring PTA 120/121 for 80-120 A

899005 Nozzle 1,0 20-50 A PTA 120/121

899006 Nozzle 1,2 50-90 A PTA 120/121

899007 Nozzle 1,4 90-120 A PTA 120/121

899008 Nozzle 1,6 120 A PTA 120/121

899016 Nozzle 2,5 gouging PTA 120/121

899031 Nozzle 1,0 20-50 A long PTA 120/121

899032 Nozzle 1,2 50-90 A long PTA 120/121

899018 Nozzle 1,4 90-120 A long PTA 120/121

899033 Nozzle 2,5 gouging long PTA 120/121

899047 Protective cup PTA 120/121

899037 Spatter shield threaded PTA 120/121

899036 Contact cutting shield PTA 120/121

899010 Spatter shield PTA 120/121

899012 Distance cutting guide PTA 120/121

899013 Bevel cutting guide PTA 120/121

899038 Contact cutting shield long PTA 120/121

899014 Circle cutting guide PTA 120/121

899045 Handle PTA 121

899314 Button PTA 25/121

899049 Hose assembly PTA 121 6m

899050 Hose assembly PTA 121 15m

899015 Spanner PTA 120/121

899040 Torch PTA 121 6m complete

899041 Torch PTA 121 15m complete

N.B. Don’t use consumables for more than 80 A with the SPLITFIRE or 100 A

with the SPEEDFIRE. The result will be poor cutting capability.

SPLITFIRE SPEEDFIRE UPPERCUT

5. MAINTENANCE

DAILY

Inspect and, if necessary, change the torch consumable parts.

Inspect and, if necessary, empty the moisture trap on the filter regulator on the rear side of the

machine. The trap is emptied by pressing the bottom sealing while compressed air is

connected. If cleaning the trap is necessary, completely unscrew the glass cup after

disconnecting compressed air.

Carefully inspect the hose assembly and torch body with regard to any leak or damage.

Never use a damaged torch.

EVERY SIX MONTHS

Disconnect the machine from compressed air and electricity. Remove the cover. Clean

the machine with dry, clean and oil free compressed air. Inspect cable connections and gas

system.

In unusually dirty environments this procedure should be carried out every month.

SPLITFIRE SPEEDFIRE UPPERCUT

6. TROUBLE SHOOTING.

Thermal overload / Air supply failure

If the fan is working, but the green READY-lamp is not lit, the air supply is not

sufficient or the thermal overload protection is active. Check the compressed air supply. If the

machine is overheated, let it cool down while switched on until the lamp lights again. Then

the machine is in working order.

Malfunction

If the pilot arc does not strike:

•The safety switch of the torch is not closed. Check that the protective cup is

properly tightened.

•Check the air pressure on the filter regulator on the rear of the machine. The

pressure should be approx. 4,5/5,5 bar.

If the pilot arc is unstable:

•Check the air pressure on the filter regulator on the rear of the machine. The

pressure should be approx. 4,5/5,5 bar.

•The machine is working two phase. Check electrical supply.

Inferior cut quality or performance:

•Check the torch consumables. Replace if necessary.

•Inspect the torch body and hose assembly with regard to any damage or leak.

•Check the air pressure on the filter regulator on the rear of the machine. The

pressure should be approx. 4,5/5,5 bar.

•Check the earth lead connection. Place the earth lead clamp directly on the work

piece. If necessary, clean from paint, dirt, rust etc.

SPLITFIRE SPEEDFIRE UPPERCUT

7. SAFETY INSTRUCTIONS

All endangerments through plasma cutting are related with the process itself. Endangerments

may occur due to:

High contact voltage

HV ignition

Electromagnetic interferences

Heat and light radiation

Gases, fumes and smoke

Noise

Hot metal and spatter

Handling of pressure cylinders

The Plasma Cutting Machine has been developed in conformity with following standards:

EN 60974-1 safety requirements for installations for arc welding and welding power

sources

Endangerment due to high contact voltage

Warning!

Before opening the plasma rectifier generally the input power has to be disconnected

physically from the mains (unplug mains cable)! Only advised personnel are allowed to

carry out any repairs to the machine.

Attention! Connect the work piece cable and earth the workplace before starting the

machine!

The power source is equipped with a cooling unit and there is an electric potential between

the housing and work piece in case the work piece isn't earthed and the machine is switched

on. Because of the high resistance of more than 10 kOhm in the coolant the contact voltage is

absolute not dangerous but sensible.

Special hints:

Connect power source only to correctly earthed mains socket with proper connected

safety conductor

Wear insulating protective clothing (safety shoes, leather apron, gloves), place torch

on insulated holder,

Make sure that they cutting area and plasma machine components are dry and clean,

arrange regular inspections.

Never short safety circuits.

Working under elevated electrical endangerment

This plasma cutting machine in conformity with valid standards (EN 60974) can be used for

operation under elevated electrical endangerment

The power source and the plasma torches are forming a safety-proofed installation

which can be separated only by using tools.

The patented design of the torch prevents electrical danger when the torch

consumables are disassembled.

Therefore the power source is marked with the S-sign and operation under elevated electrical

endangerment is allowed.

Attention! Always follow the local safety rules!

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SPT Plasmateknik AB Sistema di saldatura

SPT Plasmateknik AB

SPT Plasmateknik AB UNIFIRE 31PFC Manuale utente

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

ESAB

ESAB Buddy Arc 145 Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente