SPYKER 88 Manuale utente

spread with confidence

Spreading Chart

Operation Guide

Service Manual

Parts List

spread with confidence

It’s the spread that counts

For Models:

88, 296, 298

298

296

P.O. Box 210

810 W. Main Street

N. Manchester, IN

46962 USA

1-800-972-6130

Fax: 219-774-3416

Tools You will Need:

Screwdriver

7/16 Wrench

3/8 Wrench

Mallet

Parts You will Use:

Parts for Models:

296, 298

• (1) Drive Wheel

• (1) Idle Wheel

• (2) Handle - SS.

• (2) Bump Bar - SS.

• (1) Screw 10-24x1-3/4 Bolt

• (1) Nut 1/4 - 20

• (2) Washer - Finishing

• (2) Handle Grip

• (9) Nut

• (1) Agitator Wire

• (1) Felt Washer

• (1) Upper Spinner Shaft

• (1) Coupling

• (1) Spring Clip

• (1) Cotter Pin

• (6) 1/4 - 20x1-1/2 Bolt

• (3) 1/4 - 20x2-3/4 Bolt

• (1) Screen

• (1) Spinner

For Quick and Easy Assembly - First Read Entire Procedure

Then Follow Carefully The Step by Step Instructions

Assembly Instructions

NOTE: Painted model 296 shown in assembly instructions. 298 is stainless

frame (not shown).

Insert the ground

prop (46) into the

frame and fasten

with two bolts

(47) and nuts (5)

supplied.

Spreader Assembly

a. Mount tires on

axle as shown to

the right, noting

that the drive

wheel (33) has a

hole in the hub

for the bolt (42)

to go through the

axle and fasten

with nut (44) as

illustrated with an

arrow in diagram

2b.

2b. Washers (50)

go on either side.

Spreader Assembly

continued

Attach the idle (34)

wheel to axle with

the washer (45)

and cotter pin (25)

as shown right.

Insert handles (40)

into frame as

shown right and

fasten handles

loosely (40) to

frame (14) with 4

bolts (48) and 4

nuts (5). Attach

handles (40)

loosely together

with 1 bolt (41)

and nut (5) at

location illustrated

with arrow. Leave

the top two holes

empty until you

attach the levers.

Attach on/off

control lever (37)

and Accuway

control lever (38)

to the handles as

shown and bolt

together with two

of the longer bolts

(41) supplied (5).

Tighten all nuts &

bolts at this time.

38 37

Cable Adjustment Procedure

for Model 88 and Current Models 296 & 298

Make sure that both levers are pulled all the way

back towards the handles.

Cable Adjustment Procedure

for Model 88 and Current Models 296 & 298

Turn the rate control dial (10) to the highest

setting, (all the way past the number (9) until the

notch on the linkage stops against the flat surface

of the dial. Insert control cables in the holes in the

cable mount bracket (3) and guide the inner wire

through the hole in the cable fasteners (13). Slide

cables over so that the slots in the cable ends are

held firmly by cable mount bracket. NOTE: The

on/off control lever (37) goes into the lower hole in

this illustration which then attaches to the rate gate

linkage (9). Secure cable by inserting screw (52)

into hole of cable retainer (53) and screwing into

cable mount bracket (3). Make sure that the

diffuser assembly (12) is slid back completely

against the upper spinner shaft (28), and the rate

gate linkage (9) is slid back against the dial (10).

Now tighten the set screws in the cable fasteners

(13) to secure the wires to the fasteners.

Insert upper

spinner shaft (28)

into the bottom of

hopper so that

the end with the

hole for the

agitator wire goes

up into the

hopper.

Spreader Assembly

continued

Spinner Assembly

Insert the bump

bar (46) into

frame as shown

to the right and

fasten with two

bolts (15) that

fasten the front of

the hopper to the

frame. The bolts

go through the

bump bar and are

fastened with

nuts (5).

Slide spinner (31)

onto upper spinner

shaft (28).

Spinner Assembly

continued

Connect upper

spinner shaft (28)

and lower spinner

shaft (23).

Slide coupling (29)

onto upper spinner

shaft (28).

Slide coupling (29)

down to secure

connection of

upper & lower

spinner shafts.

Spinner Assembly

continued

Snap the loop of

the spinner clip

(30) around upper

spinner shaft (28)

to secure spinner

(31).

Insert spinner clip

(30) through hole

in spinner (31) and

hole in upper

spinner shaft (28).

NOTE: Use upper

hole in spinner

shaft for the

regular spinner

(31) and use the

lower hole for the

mulch spinner.

The slot in the dial

is to allow the rate

gate linkage to

travel all the way

open for the mulch

setting on models

296 & 298 only.

Exploded View Model 88

Rear View

39 Screen

54 Retainer Wire

Hopper & Frame

Assembly

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SPYKER Spargitore

SPYKER

SPYKER S80-12010 Manuale utente

SPYKER

SPYKER S100-12010 Manuale utente

SPYKER

SPYKER P20-5010 Series Manuale utente

SPYKER

SPYKER S100-12010 Manuale utente

SPYKER

SPYKER SPY50L-2S Manuale utente

SPYKER

SPYKER KSPLS15 Manuale utente

SPYKER

SPYKER S80-12010 Manuale utente

SPYKER

SPYKER SPY200T-1P Manuale utente

SPYKER

SPYKER P40 Series Manuale utente

SPYKER

SPYKER S40 Series Manuale utente

SPYKER

SPYKER P60 Series Manuale utente

SPYKER

SPYKER S100-12011 Manuale utente

SPYKER

SPYKER S60-12020 Manuale utente

SPYKER

SPYKER BCS25 Manuale utente

SPYKER

SPYKER R28-1824 Manuale utente

SPYKER

SPYKER S30 Series Manuale utente

SPYKER

SPYKER PRO Series Manuale utente

Manuali Spargitore popolari di altre marche

PEQUEA

PEQUEA GT-100 Manuale utente

Herculano

Herculano H2RS9 Manuale utente

Epoke

Epoke SKE8 Manuale utente

GEA

GEA EL44 Scheda tecnica

Boss Snowplow

Boss Snowplow TGS 800 Manuale utente

Fisher

Fisher EMERSON 168 Series Manuale utente

Fisher

Fisher POLY-CASTER 78601 Manuale utente

TurfEx

TurfEx RS7200 Manuale del proprietario

Ferris

Ferris Pathfinder Series Manuale utente

Fayat Group

Fayat Group DYNAPAC S100 Guida alla risoluzione dei problemi

Art's-Way Manufacturing

Art's-Way Manufacturing X700 Manuale di installazione e funzionamento

EASTMAN

EASTMAN CR 500 Manuale utente

Nogueira

Nogueira RoyalFlow-600 Manuale utente

Buyers

Buyers TGS05B Manuale utente

Magnum

Magnum V-BOX PV Series Supplemento

Meyer's

Meyer's VB280 Manuale utente

SnowEx

SnowEx VX-4210 Manuale utente

Kramer

Kramer VM-400HDCP Manuale utente