Square Perfect SP3700 Manuale utente
SP3700 VARIABLE POWER
STUDIO FLASH SET
Make every picture perfect
Qty. 2 Professional Studio Strobes
(150 Watt-Seconds) 100-watt modeling light.
Qty. 2 Light Stands (extends 31" to 78”)
Qty. 2 Softbox (20" X 28")
Qty. 1 Umbrella (33" gold reflection umbrella)
Qty. 1 Carry Bag (Carries strobes, light stands, umbrella
and accessories)
Qty. 1 Backdrop stand with carry bag
Qty. 1 10’x20’ Backdrop
Qty. 2 10’x13’ Black and 10’x13’ White backdrop
SP150S
Qty. 1 Synch Flash B (45-Watt/Second)
Includes A/C screw socket with umbrella holder.
Qty 1 Light Stand (extends from 16” to 42”)
Accessories:
Qty. 1 Collapsible
(32" double sided - Gold/Silver)
Qty. 1 Four Leaf Barn Door
Qty.1 Set of 4 Color Gels
Qty. 1 Honeycomb Diffusion Filter.
Qty. 1 Narrow Snoot
Qty. 1 4 Channel Wireless Trigger Device
Reflector
SP3700 Professional Series Studio Light Kit
K
www.squareperfect.com
O
L
M
N
O
N
M
L
K
©2007 All rights reserved Square Perfect Photo.
SP3700 Flash Studio Kit
Thank you for your purchase of the SP3700 Flash Softbox Studio Please read this manual carefully before use, and keep it handy
kit. This manual has been written to help you with the assembly, for use during break down of equipment. Please read and heed
operating procedures and accessories. Square Perfect's all safety precautions listed in this manual. For ordering spare
SP3700 Flash Kit is manufactured with the finest material b u l b s o r r e p l a c e m e n t p a r t s , c o n t a c t u s a t
available. Your flash kit will provide many years of quality service [email protected]. Also check out our extended line of
with proper care and handling. photo equipment now available.
SP150 lamp body with
reflector attached.
Nylon Carry Case. Two layers, bottom for storing light stands, Adjustable compartments for easy storage of light units.
Four leaf barndoor. Red, blue, yellow frosted and
honeycomb filter.
Technical notes for use:
Remove protective cover
from mounting tip before
attempting to place flash
head on stand.
1. Swivel screw.
2. Umbrella rod mount.
3. Mounting screw
Four panel softbox set.
with lamp connector.
1.
2.
3.
Highlight / Fill strobe lamp body
and lamp holder. Defusion lense.
Snoot will direct light to exact spot without
affecting surrounding area. Easy attachment.
Varigated dye backdrop
Black backdrop
White backdrop
Umbrella - double layered
reflective inside light proof
backing.
Complete backdrop stand
assembles in minutes. Bars
attattach and lock with a quarter
turn.
Gold/silver reflector
and gold umbrella
for creative fill techniques.
©2007 All rights reserved Square Perfect Photo.
Attach four leaf barn door
to reflector on flash head.
If fill strobe is not working, be sure
to check the on/off switch. Located
on the back of the lamp holder.
Four leaf barn door set with color filter or
honeycomb slide in for quick change.
1. On/Off electric supply.
2. Variable flash dial.
3. On/Off variable, model lamp.
4. Flash ready light.
5. Flash test.
6. Sync receptacle.
7. Safety fuse.
8. Slave dome
1.
2.
3.
9.
5.
8.
7.
Specifications:
1. Pictured is the SP3700 lamp
ring connector shown with the
large end of the flex rod inserted.
2. Small end of flex rod fit into
corner pocket on the softbox
tent.
5. Pull the velcro strap down
and into place.
Note: the rods take a good
deal of force to flex into position.
6. Before the softbox ring can be
attached to the SP3700, the re-
flector must be removed.
7. The softbox speed ring can
be attached in the same manner
as the reflector.
8. Next attach the inner defusion
lens using the elastic/velcro tabs.
9. Attach the outer diffusion
lense to velcro patches on
the outer edges.
10. The outer lens will have a
snug fit smooth surface when
installed properly.
SP150S Lamp Head Operation:
SAFETY PRECAUTIONS:
•Become thoroughly familiar with this product before use. Run •Wait until the bulb is completely cool before touching or
through at least one practice assembly and breakdown before removing it.
you schedule a shoot. •Never use the SP lamp outside in a wet environment.
•Make sure that the main voltage corresponds to that stated on •Never move the appliance by pulling the cord. Make sure the
the SP lamp. Account for number of lamps in use. cords do not come in contact with halogen bulb. Do not wind
•Never leave the lighting unsupervised when in use. Keep the cord around the appliance.
children or incompetent persons away from lighting equipment. •Stand the SP on a flat surface only to prevent toppling.
•If the lamp or the cord show sign of wear or damage, it should •Do not touch the metal parts on the lamp while in use, these
be replaced or repaired by a qualified electrician before use. metal parts will become very hot.
Softbox Assembly:
3. Next insert the fourth rod
into the SP 4" ring. Note: Keep
the velcro flaps at the ring
open to allow sufficient slack.
Power Input : AC110-130 volt, 60 Hz
Flash Power : 150w (joule) in full
Guide No. : GN32
Color Temperature : 5600K
Flash-Tube Lifetime : over 8,000 typical flashing
Flash Power Setting : 1/8 to full
Recharge Time : 2 seconds in full
Flash Duration : 1/600 sec.; 1/1000 sec.
Slave Range : 35ft /10m
Lighting Range : 55 degree
Modeling Power : Halogen 100w
Synch Voltage : 5 volt
Fuse : 6A
Dimension : 4" x 7-1/2"
Weight : 1.8 Lb (800g)
4.
6.
10.
11.
9. AC recepticle
10. Flash ring
11. Model lamp
3.
©2007 All rights reserved Square Perfect Photo.
4. Next insert the fourth rod
into velcro strap pocket.
Electronic Radio Trigger Device
www.squareperfect.com
F o r o r d e r i n g s p a r e b u l b s o r
replacement parts, contact us at
out our extended line of photo
equipment. Before replacing bulbs be
sure to read the instructions and follow
the safety procedures.
©2007 All rights reserved Square Perfect Photo.
Replacement Bulbs
Before attempting any of the following
procedures UNPLUG the unit. Next
check the fuse found on the back of the
unit. If it is tripped replace it. Plug the unit
in and recheck the flash bulb.
If it is determined the bulb is faulty, a
replacement can be ordered from
BULB replacement is simple and easy.
Before handling new bulbs remember to
wear clean cotton glove. Oils from skin
will cause premature bulb failure.
Hold bulb close to base. Gently push the
two prongs into the receiving holes.
Next attach spring retaining strap.
Strobe flash bulbs may vary in
appearance and shape from model to
model, replacement procedures remain
the same unless noted.
The SP3700 Flash Kit is shipped with the a
Wireless Triggering Device for your convenience.
It is an easy to use device that will give you extra
control in the photographic studio environment.
The Wireless Triggering Device is designed to
work with a variety of flash units. We provide a
wide range of sync cord adaptors to fit most
popular brands.
The Wireless Triggering Device has four channels
and uses a 23A battery (installed). The receiver
uses two AAA batteries (not included).
1. To use the Wireless Triggering Device, first
slide the trigger into the hot shoe found on top
on your camera. If a hot shoe is not available,
use the sync cord attachment found on the
side of the trigger device.
3.Switch the receiver unit ON/OFF button to the
ON position. Press the test button located on
the top of the trigger unit. You will see a
twinkling of the LED on the receiver unit. This
indicates the trigger is working properly and is
locked-in on a working channel of the receiver.
4. Switch the remote flash unit power switch to
the ON position with the receiver attached.
Push the test button on the trigger, it should
trigger the remote flash unit.
5. To change channels on the trigger, slide the
channel switch on the side of the trigger
device to one of four positions. Next press the
power switch on the receive unit twice to reset
the receiver.
2. Attach the receiver to a remote flash unit. Use
the proper sync cord adaptor provided, plug
into sync cord socket.
Indice
Altri manuali Square Perfect Flash della fotocamera
