SRP GT Manuale utente
INDEX
1. GENERAL INFORMATION.............................................................................................. 3
1.1. Preliminary warnings............................................................................................. 3
1.2 Manufacturer's address:......................................................................................... 3
1.3. Technical Service Address ..................................................................................... 3
2. DESCRIPTION OF THE PEDALS....................................................................................... 4
2.1. General description ............................................................................................... 4
2.2. List of parts supplied.............................................................................................. 4
2.3. Working principle .................................................................................................. 4
2.4. Intended use.......................................................................................................... 5
2.5. Predictable working conditions............................................................................. 5
2.6. Control panel ......................................................................................................... 5
2.7. Identification and signalling .................................................................................. 5
3. WARNINGS AND SAFETY INSTRUCTIONS ..................................................................... 6
3.1. Protection and safeguards..................................................................................... 6
4. STORAGE AND TRANSPORT.......................................................................................... 6
4.2. Weight and dimensions......................................................................................... 6
4.3. Storage................................................................................................................... 6
4.4. Transport and handling ......................................................................................... 6
5. LOCATION ..................................................................................................................... 7
5.1. Unpacking.............................................................................................................. 8
5.2. Site preparation..................................................................................................... 8
5.3. Assembly................................................................................................................ 8
5.4. Electrical connection ............................................................................................. 8
6. REVIEWS BEFORE STARTING......................................................................................... 9
6.1. Fastening................................................................................................................ 9
6.2. Review with the pedals connected........................................................................ 9
7. INSTRUCTIONS FOR USE ............................................................................................. 10
7.1. Pre-inspection and adjustments.......................................................................... 10
7.2. Uses of the controls............................................................................................. 10
7.3. CONTROL SETTINGS............................................................................................. 10
7.4 - Download and use of the application. ............................................................... 13
8. MAINTENANCE ........................................................................................................... 14
8.1. General cleaning.................................................................................................. 14
8.2. Replacement of elements.................................................................................... 14
9. ATTACHMENTS ........................................................................................................... 15
9.1. Plan of general measures: ................................................................................... 15
10. DECLARATION OF CONFORMITY .............................................................................. 16
11. “CE” BRANDING........................................................................................................ 17
12. WARRANTY ............................................................................................................... 17
13. RECEIPT OF TECHNICAL DOCUMENTATION ............................................................. 17
3
1. GENERAL INFORMATION
1.1. Preliminary warnings
Be sure to observe the safety and warning notes in this manual when using the pedals.
It is essential that you follow these instructions for the pedals for issue-free operation and to be
able to file a claim under the warranty.
The pedals must be used for the purpose for which they were built. Any other use is considered
dangerous. Any liability of the manufacturer for damage that may be caused by non-compliance
with the instructions in the manual is excluded.
This manual contains important information about the operation of the pedals. For this reason it
should always be kept within reach of the user.
1.2 Manufacturer's address:
Sim Racing Pro 2018 S.L
Carretera de Tordera, 89
17300 Blanes (Girona)
Spain
Tel + 34 627 639 716
info@simracing-pro.com
1.3. Technical Service Address
Sim Racing Pro 2018 S.L
Carretera de Tordera, 89
17300 Blanes (Girona)
Spain
Tel + 34 627 639 716
4
2. DESCRIPTION OF THE PEDALS.
2.1. General description
This technical manual contains all the necessary instructions for the installation, commissioning,
maintenance and use of the pedals.
Parts of the pedals:
One Base, 3 pistons, set of three pedals, accelerator, brake and clutch.
Electrical power supply of the machine:
. Power and electricity consumption: 5 volts USB-C
. Model: Sim Racing Pro
. Total Power: 225mW
. Total consumption: 45mAh
. NOTE: These consumptions are always approximate since they depend on the performance of
each element.
2.2. List of parts supplied.
1. set of pedals
2. 1 pc Allen key nº3
3. 1 pc Allen key nº4
4. 1 pc Allen key nº5
5. 1 pc. 10 mm open-end wrench
6. 1 pc open end wrench 13 mm
7. 1 x 2m USB cable / USB-C to USB-A
8. 1 user manual / CE certificate
9. 1 Warranty form
2.3. Working principle
The SRP GT pedals
They have the following functions:
Driving Simulation
5
2.4. Intended use
Driving simulation when playing PC car racing games.
Do not carry out activities other than those for which the pedals are designed with elements other
than those indicated here.
The manufacturer of the pedals declines all responsibility for failure to comply with this warning.
Do not exceed the working capacity of the pedals.
2.5. Predictable working conditions
People over 6 years old may use the pedals.
The fastening of the pedals is essential for their proper functioning.
The correct use of the pedals and their maintenance implies their longevity.
2.6. Control panel
See point 7.3
2.7. Identification and signalling
Signal symbols that can be found on the pedals:
DANGER! Electrical risk
Electrical risk in electrical panel and indicated areas.
Note: The user must ensure that all the identification signs and warning plates on the pedals are
maintained and preserved
Under no circumstances should they be dismantled or altered.
6
3. WARNINGS AND SAFETY INSTRUCTIONS
3.1. Protection and safeguards
The materials used in the manufacture of the pedals do not give rise to any hygienic risks, although in
the event of fire the plastic components and lubricants may give rise to toxic fumes.
Do not carry out any maintenance or cleaning operations on the pedals or the pavement in the vicinity
without first disconnecting the USB from the P
4. STORAGE AND TRANSPORT
4.1. Reception of the pedals.
1. Check whether the pedals have been damaged during transport.
4.2. Weight and dimensions
Model
Length, mm.
Width, mm.
Height, mm.
Weight, Kg.
SRP GT
441
347
245
8.1 KG
See general dimensional drawing 9.1.
4.3. Storage
No particular measures are recommended with regard to storage. If the user leaves it unused for a
long time, it is recommended to protect it from dust by covering it properly and disconnecting it from
any power source beforehand.
4.4. Transport and handling
If the pedals have to be transported to another location, make sure that the instruction and
maintenance manual is with the pedals so that it can be consulted at the new location.
The total weight of it must be taken into account.
7
5. LOCATION
The pedals have been designed and are built expecting their assembly.
8
5.1. Unpacking
After transport and unloading, with the pedals in the vicinity of the intended assembly site, unpacking
should be carried out with the utmost care and attention.
The pedals should not be installed if any damage is observed during unpacking. In case of questions, do
not use the product and ask the supplier for information.
5.2. Site preparation
The surface on which the machine is to be installed must take account of the weight of the pedals, as
indicated in section 4.1 above.
It is recommended that it be placed on a metal frame where it can be fixed correctly. It can also be
placed directly on the floor on a carpet or rubber surface.
5.3. Assembly
5. Once the machine is located and level in the place where you will work on it, it can be installed and
connected.
5.4. Electrical connection
Indice
