SRS Labs GMC12-WLV-3H24 Manuale utente

(1 /16)

Instruction Manual

Models:

version 1.0 since 6 November 2018

ATTENTION!

This instruction manual contains important information about the installation and the use of

the equipment. Please read and follow these instructions carefully.

Always ensure that the power to the equipment is disconnected before opening the

equipment or commencing any maintenance wor .

GMC12-WLV-3H24_en_manual_M237

ireless Controller for

Low Voltage Hoist

GMC12- LV-3H24, -12H6

GMC8- LV-2H24

(2 /16)

Safety information

IMPORTANT INSTRUCTIONS

All safety and operating instructions should be read before the equipment is installed or operated.

IMPORTANT SAFETY INFORMATION

The following general safety precautions have to be observed during all phases of operation, service,

and the repair of this equipment. Failure to comply with these precautions or with specific warnings

in this manual violates safety standards of design, manufacture, and the intended use of this

equipment.

Do not operate in an explosive atmosphere!

Do not operate this equipment in the presence of flammable gases or fumes. Operation of any

electrical instrument in such an environment constitutes a definite safety hazard.

ater, moisture, heat and humidity

Do not operate this equipment near water or in areas with wet floors or in high humidity atmosphere,

where condensation forms on the equipment. It should never be placed near or over a heat register

or other source of heated air and it should not be installed or operated without proper ventilation.

(3 /16)

Functions and Control

Motor Controller has been designed to control from 1 to 12 electrically compatible motors, either

separately or simultaneously – controlled via switches located on front panel or wireless

remote/pendant. Optionally you can lin GO/STOP button by lin connector.

Each device is equipped with unique APA /Automatic Phase Align/ module that guarantees that on

any alignment of input phases the motors will move in the correct direction. If any line wire is

disconnected, the hoist controller stops to ensure safe operation. Unit is also equipped with AVM

/Automatic Voltage Metering/ module. This module chec s the main voltage for AC400V +-20% and

the star configuration. if there is any problem with the main voltage, you’re notified, and unit will not

run any hoist.

Unit will not wor when:

 One phase is missing

 Under-voltage is present on lines

 Over-voltage is present on lines

All electrical components carry their own individual cSA/UL, CE and comply with European Directives.

The components are housed in robust steel 19" rac casing with powder coating. Complete unit

complies with the CE according the Certification of conformity attached to this manual.

Operation

The motors/hoists connected with the GMCseries controller can be activated individually or

simultaneously using the GO switch located on the front panel or wireless remote. Units can be

optionally lin ed together to create bigger systems.

How to start

 Connect the CEE32/5p plug to the AC400V +-20% power supply – turn the ey to ON

position. When the main power is OK, the power LED will light green, otherwise the unit is

OFF. Chec phase voltages, frequency and contact the manufacturer if help is needed.

 Connect the plugs for the electric hoists to the output soc ets.

 Chec that the emergency STOP mushroom on the device is not engaged or any other lin ed

device in system.

Move lever on the front panel or WMC remote corresponding to each motor to the required

position:

o UP - Lever in upper position

o STAY – Lever in middle position

o DOWN - Lever in lower position

 Pushing the GO button will activate the motors to move simultaneously

 Releasing the GO button will stop the movement of the motors simultaneously.

 When the device is not being used, it is highly recommended to turn it OFF by the ey

located on the front panel.

(4 /16)

To Move a single/several hoist(s)

 Set the UP/DOWN toggle switch for certain motor to the desired direction. The associated

LED should light green for UP, or red for DOWN direction

 Hold the GO button until the motor is moved the desired height, then release.

WMCseries remote controller

WMCseries remote allows control of the device via wireless connection.

(5 /16)

STOP

This latching pushbutton switch turns the Hoist Control system off. Once the STOP button has been

pressed, it loc s the unit to OFF position and must be rotated cloc wise and released before

disengaging.

This pushbutton switch turns the selected channels of Hoist Control system ON, when the unit is

active. Once the GO button has been pressed, the energizing of the hoists is ON. The bac light of GO

button in local mode on the Base unit is ON only when one or more direction switches are in active

position /UP or DOWN/.

DIRECTION SWITCHES

They allow changing of the direction of movement for each motor/hoist separately:

BATTERY STATUS LED

Battery status LED indicator:

 Green: 100-90%

 Orange: 90-10%

 Red: 10%

 Red + beep: 5%

REMOTE STATUS LED

Status LED indicator of WMC remote unit:

 Green: Power ON

 Green blin ing: Power ON – SLEEP - move the direction switch or press GO button to resume

from sleep. This status becomes after 3 minutes of inactivity.

 Orange: Indicates direction switch activity

 Red: GO button is pressed – sending commands to the Base unit

(6 /16)

Link of WMC remotes

Up to two WMC remotes can be lin ed together to group the operation of STOP and GO buttons. To

lin two WMC units, 5-pin miniXLR cable with custom wire connection is needed.

Never use 1 1 cable – remotes can be destroyed.

When WMC remotes are lin ed, the GO and STOP buttons are lin ed – so press of any STOP and GO

button will wor for both lin ed devices.

Link of Base WLV units

Up to 30 Base units can be lin ed via lin connector located on the front panel.

To lin two WMC units, 5-pin DMX data cable is needed.

Due to safety requirements, the link function works only in LOCAL / LINK MODE

of the controller.

(7 /16)

GMC12-WLV series Base unit

GMCseries front panel

Hoist protection

 GMC12: Each three hoists are protected by single C16/3p MCB

Power key switch positions

 OFF: Power OFF /Only battery charger is active in this state/

 PICKLE: Power to the hoist is enabled

 AUTO: Power to the hoist is enabled when GO command is received

GROUP STOP key switch positions

 OFF: Trip of any brea er or mains GFI brea er will not cause E-STOP

 ON: Trip of any brea er or mains GFI will cause E-STOP of the unit

MODE key switch positions

 Local / LINK: Device wor s via local control or via networ in lin ed operation

 Radio Remote: Device is controlled via wireless radio remote

RESET

RESET button wor s for the SIL3 E-STOP relay reset. RESET needs be pressed every time after the

unit is turned ON, the E-STOP mushroom has been pressed or when the GROUP STOP has been

activated.

(8 /16)

EMERGENCY STOP

E-STOP is a red color mushroom. Once the E-STOP button has been pressed, it loc s the unit into

active position and must be rotated cloc wise and released before disengaging. After engaging the

E-STOP button, the RESET button needs to be pressed to reset the system.

This green pushbutton turns the selected channels of Hoist Control system ON when is active. Once

the GO button has been depressed, the energizing of the hoists is turned OFF.

DIRECTION SWITCHES

They allow changing the direction of movement for each motor/hoist separately or in groups. LED

close to the switch indicates the movement direction.

Charger status LED

Status LED of charger located on the front panel is

 Green: Battery is fully charged

 Green blin ing: Battery is charged to 90% or greater capacity

 Orange blin ing: Not in rapid mode – waiting to be charged

 Red: Battery is in rapid charge mode

 Red blin ing: Battery is ultra-rapid charge mode

 No LED: Battery is not inserted

Limit STOP input

LIMIT STOP connectors for external E-STOP from NLP device.

Link input

Lin input for lin ing of GMC units.

(9 /16)

GMCseries rear panel

(10 /16)

MAINS

Mains input on 1.5m cable + fuse for mains transformer T2.5A.

AUX output

AUX output for additional AC230 powered devices. Protected by C16/1p brea er on the front panel.

Output connectors wiring

Harting 24 Female

Function

2 L1

5 L3

M2 down

8 M2 common

M2 UP

M4 down

11 M4 common

M4 UP

14 L1

17 L3

M1 down

20 M1 common

M1 UP

M3 down

23 M3 common

M3 UP

Body

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali SRS Labs Controllori

SRS Labs

SRS Labs SIM960 Manuale operativo

SRS Labs

SRS Labs RMC12, RMC8 Manuale utente

SRS Labs

SRS Labs GMC12-LV-H6 Manuale utente

SRS Labs

SRS Labs ADR24-DIGI-AHD Manuale utente

SRS Labs

SRS Labs CTC100 Manuale utente

SRS Labs

SRS Labs IGC100 Manuale utente

SRS Labs

SRS Labs GMC4-LV-H6 Manuale utente

Manuali Controllori popolari di altre marche

Digiplex

Digiplex DGP-848 Istruzioni operative

YASKAWA

YASKAWA SGM series Manuale utente

Sinope

Sinope Calypso RM3500ZB Manuale utente

Isimet

Isimet DLA Series Style 2 Manuale di installazione

LSIS

LSIS sv-ip5a Manuale utente

Rockwell Automation

Rockwell Automation 1769-L31 Manuale utente

Airflow

Airflow Uno hab Manuale utente

ABB

ABB ACS580-01 drives Manuale utente

Panasonic

Panasonic GM1 Series Manuale utente

Emerson

Emerson SW93 Manuale utente

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuale utente

Panasonic

Panasonic FP? Positioning Unit RTEX Manuale utente

Samson

Samson Type 5824 Manuale di servizio

Alpha IP

Alpha IP MIOB 21001 Manuale utente

Siemens

Siemens OpenAir GMA 1 Series Manuale utente

Surecom

Surecom SR-629 Manuale utente

Fishman

Fishman TriplePlay Manuale utente

Regulus

Regulus SRS1 T Manuale utente