SRS Labs MPROX Istruzioni di montaggio

Smart.Netv2

PC BASED DOOR ACCESS CONTROL

DESKTOP – WEB – MOBILE

I N S T A L L A T I O N & H A R D W A R E G U I D E : I S S U E 2 0 1 7 / 3

Door Control Unit Installation..............................................................................................4

Planning....................................................................................................................... 4

Power Supply................................................................................................................. 4

Cable & Wiring Choices..................................................................................................... 4

End of Line Termination.................................................................................................... 5

Door Monitor Contact Input................................................................................................ 5

Alarm Relay Output......................................................................................................... 5

Exit Request Input........................................................................................................... 6

Door Reader Connections.................................................................................................. 6

Testing a DCU Door Control Unit Installation Locally .................................................................7

Door Control Unit Serial Address..........................................................................................7

Door Control Unit Wiring Diagram........................................................................................8

USB-485-ISO-TB Boxed Isolated Network Adapter Interface.........................................................9

Power Source................................................................................................................. 9

Connections.................................................................................................................. 9

Interface Commissioning................................................................................................... 9

USB-485-RPI-TB Boxed Network Adapter Interface..................................................................10

Power Source............................................................................................................... 10

Connections................................................................................................................. 10

Interface Commissioning..................................................................................................10

LAN-IP-485-TB Boxed Isolated Network Adapter Interface.........................................................11

Power Source............................................................................................................... 11

Connections................................................................................................................. 11

Status LED’s................................................................................................................. 11

Removable PCB Links...................................................................................................... 12

Adapter IP Addressing..................................................................................................... 12

Firewall Considerations................................................................................................... 12

LAN IP Device Installer Utility............................................................................................13

Advanced LAN Setup....................................................................................................... 14

LAN Adapter Serial Settings..............................................................................................14

Installing System Doors in Remote Locations..........................................................................15

Router & Port Forwarding Considerations..............................................................................15

Multiple Adapters at Remote Locations................................................................................15

Private Cloud & Remote Management..................................................................................15

Activating the Private Cloud Web Service..............................................................................15

Working Over The Internet...............................................................................................15

Starting the Private Cloud Service at Boot Time......................................................................15

Private Security Key Coded Access Credentials.......................................................................16

Standard PSK Coding.......................................................................................................16

Customer Specific PSK Coding............................................................................................16

Disabling PSK System Coding............................................................................................. 16

USB Desktop Enrolment Reader..........................................................................................17

Installing.................................................................................................................... 17

Testing....................................................................................................................... 17

PSK Coded Access Credentials...........................................................................................17

Secure Login................................................................................................................ 17

Access Control System Schematics .....................................................................................18

Access Control Door Equipment..........................................................................................18

USB-485 Adapter Networking.............................................................................................19

USB-485 + LAN-IP-485 Adapter Networking............................................................................19

The following manual details information relating to the Door Access Control System hardware installation only.

They replicate and collate instructions that may also be provided with the appropriate electronic devices or sub-

systems. Details on how to program and configure your installation are provided through web pages reachable

from the Desktop Administration Console software by selecting the 'help online' feature.

Door Control Unit Installation

Best results will be achieved when following these instructions as they describe the planning and installation of a

single Access Control Door or Entrance. A wiring diagram with notes is shown below, that states clearly all the

common associated devices that may be required for each single door installation. The main circuit board can be

removed during enclosure installation but must be stored and handled with care.

Planning

The DCU Single Door Control Unit is designed to be installed locally to the door or entrance it will serve in a dry

internal location. This allows all cable connections to be short and efficiently run. All connections are made by

removable side-entry polarised screw terminals designed for multi-stranded cable types. All cables entering the

door control unit housing must not be coiled up inside but routed efficiently through the various edge and rear

cable entry knock-outs and drill points of the enclosure. Cable tidy anchor points are provided with suitable cable

ties provided. Please ensure that the rear enclosure mounting screws do not foul the PCB or terminals.

Power Supply

The DCU can be powered from a single low voltage DC regulated supply only. The voltage input range must be

between 8-16 Volts DC; ratings outside of these may cause damage to the control unit and / or its associated

devices. The DCU single door control unit has been designed for low power operation. Its quiescent current is

only 80mAmp rising to 300mAmp with both proximity readers connected and the lock and alarm relays

energised.

Always use an individual power supply to power each door and its associated local

components in isolation. Never share the power supply between adjacent door control unit

as ground loops may be created that can cause communication bus faults over the RS485

interconnecting network. The current capacity of the PSU should be greater than the locking

peak current consumption by at least 300mAmp (0.3A).

Cable & Wiring Choices

The correct choice of cable types will affect the overall performance and cost of the system installation so care

and understanding of the types and when to use them is important.

The use of CAT5/6 or similar cable is not recommended as its solid core construction breaks

easily under mild mechanical stress and will make service & repair difficult.

The differing types of cable and when to use them are explained in the table below:

Application Cable Type Max Distance Notes

Communication BELDEN 8132

BELDEN 9842

6CORE SECURITY

1200 M

50 M

Use Belden equivalents if required.

Screen is connected to

communications terminal G from

Adapter to the door control unit

Readers BELDEN 9535

6 CORE SECURITY

50 M

10 M

Connect the screen to OV reader input

Power & Lock 4-6 CORE SECURITY 50 M Any suitable unscreened power hook

up cable can be used with sufficient

conductor area for the current drawn

Egress & Contact 4-6 CORE SECURITY 50M Any suitable unscreened hook up cable

can be used

The total networking communication length must not exceed 1.2KM (1200M) from a single USB-485 or LAN-IP-

485 Adapter and must not contain any spurs or star points. You can connect up to 128 DCU Door Control Units on

one continuous network cable installation from one USB-485 or across multiple LAN-IP-485 Adapters (segments).

End of Line Termination

In the last door control unit which is the one furthest away from the USB or LAN-IP interface connection you must

employ end-of-line resistor termination. Connect the two 120-Ohm resistors provided with the USB-485 or LAN-

IP-485 Adapters, one across the last door control unit terminals T+ & T- and the other across R+ & R-. To check

that the termination is correct, disconnect the USB-485 or LAN-IP-485 interface from the computer or network

switch and measure with a multi-meter set on the resistance range that you can read between 60 to 70 ohms

across the T pair and again across the R pair. The exact readings will depend on the total networking cable length

and its resistance.

Door Monitor Contact Input

The Door Monitor Contact input is used to monitor the physical state of the door in its frame or closed position.

This is normally achieved with a standard intruder alarm magnetic contact set. The type required is single-pole

normally closed when the door is closed. The Door Monitor Contact will only monitor the physical state of the

door and not the locked or security status of the lock. The Door Monitor Contact will activate the Alarm Relay

Output (Relay 2) when one of the following two conditions are met. If the doors lock mechanism is defeated and

the door is opened by force or if the door is opened through a valid access, but then not closed correctly

afterwards. The timing or delay of these events is programmable through the Desktop Administration Console

software.

Alarm Relay Output

The Alarm Relay Output (Relay 2) can be used locally to the door or entrance to indicate if the door or entrance is

in the alarm state. An alarm state condition is generated when the door monitor contact is fitted and the door is

forced open or left open too long. Any general purpose sounder or other device may be switched with a rating

not greater that 24VDC at 2A. The relay has normally open and closed volt free contact set (Form C). If the

magnetic door contact is not fitted to any door control unit then this condition is automatically detected and

disabled (no need to link out).

Exit Request Input

The Exit Request Input is normally used if an button is required to exit through the controlled door or entrance. It

can be reassigned on the software to be used as a general purpose input for other purposes if required.

Configurable options available are, intruder alarm set detect, power supply fault detect, general tamper input

detect and release (free access) all system doors on a single closing contact. By default (factory) the operation is

as an Exit Request Button utilised with a push-to-make momentary switch. If the exit button function input is

later reassigned by the software application all functions are normally open with a closing circuit for an active

state. If the release (free access) all system doors function is required only a single connection at one door control

unit is required as the Host Computer running the software, will manage the command for the rest of the system.

Never apply a voltage of any kind to this input as damage to the control electronics will occur.

Door Reader Connections

Reader connections are generally of a short distance and so you may use standard intruder alarm connection

cable. Please observe the above cable choices table for exact types depending on distance to the appropriate

reader input on the door control unit. Below are the wiring colours for the standard reader types you may

encounter:

Reader Model Type Connections Notes

MPROX 125KHZ ASK 26 Bit

Wiegand

RED = 12V

BLACK = 0V

GREEN = D0

WHITE = D1

BLUE = GLED

Use screened Belden 9535 over 10M

MPROX + PIN 125KHZ ASK 26 Bit

Wiegand with 4 Bit PIN

Function

RED = 12V

BLACK = 0V

GREEN = D0

WHITE = D1

Use screened Belden 9535 over 10M. Set

door control unit reader type to MPROX+PIN

at the software

MPROX - MF 13.56MHZ Smart Card

Serial Number Reader

(CSN)

RED = 12V

BLACK = 0V

GREEN = D0

WHITE = D1

YELLOW = GLED

Use screened Belden 9535 over 10M

MPROX – MF - KP 13.56MHZ Smart Card

Serial Number Reader

(CSN) c/w PIN Keypad

RED = 12V

BLACK = 0V

GREEN = D0

WHITE = D1

YELLOW = GLED

Use screened Belden 9535 over 10M

UPR - DOOR ENTRY DIRECT 125KHZ Universal

Proximity Reader

RED = 12V

BLACK = 0V

GREEN = D0

WHITE = D1

BLUE = GLED

Use screened Belden 9535 over 10M

HID PROXIMITY READERS 125KHZ WIEGAND

FAMILY

RED = 12V

BLACK = 0V

GREEN = D0

WHITE = D1

ORANGE = GLED

Use screened Belden 9535 over 10M

Testing a DCU Door Control Unit Installation Locally

The majority of each individual door control unit installation can be tested in isolation to confirm correct

installation before connecting to a network of doors and the control computer. This is recommended as it will

ensure a smooth flow to the next stage of networking the doors and connecting to the control computer.

The Lock, Exit Button, Magnetic Door Contact, Relay 1, Relay 2 and both Proximity Door Readers if fitted, can be

simply checked for correct operation.

1) To test that the Door Lock (Relay 1) is operating correctly briefly press the Request to Exit Button. The Door

Lock should unlock for approximately 5 seconds and then relock.

2) To test the Door Lock (Relay 1) and the Alarm Output (Relay 2) briefly press the Request to Exit Button and

then open the door thus opening the Magnetic Door Contact. The Door Lock should relock within about 5

seconds. After 20 seconds, if the door is still open (ajar) then the Alarm Output Relay 2 will operate until the door

is closed and secure.

3) To test for Door Forced Open you will need to disable the door locking mechanism and without pressing the

Request to Exit Button open the door which in turn opens the Magnetic Door Contact. The Alarm Output Relay 2

will operate until the door is closed and secure once again.

Other readers are available but their feedback signals may differ. The DCU control unit is

fitted with two industry standard 26 Bit Wiegand interfaces so many readers of all types

including bio-metrics may be used.

4) To test each Proximity Reader present a card or tag at each unit installed. The reader should beep and flash

green briefly to indicate the reader has read the presented compatible token. After about 2 seconds the door

control unit will flash the red light to green 6 times to indicate that this token has been read and processed but is

unknown to the Door Control Unit (access denied).

It is not possible to test the correct operation of the RS485 network at this stage.

Door Control Unit Serial Address

It is recommended at this stage that the unique serial number located on white label is recorded along with a

descriptive name for the door location. The serial number provides the unique address required to find it on the

multi-drop RS485 network or network segments. This information will be required when the software is installed

on the control computer and door records are to be defined, addressed and commissioned.

Door Control Unit Wiring Diagram

USB-485-ISO-TB Boxed Isolated Network Adapter Interface

Best results will be achieved when following these instructions as they describe the installation and

best practice for this adapter product. The USB-485-ISO-TB Adapter has been designed to simplify

the connection of a multi-drop network of DCU Door Control Units. You can use this product to

connect the control computer to up-to 128 Door Control Units from a single USB connection. This

adapter variant has been improved to achieve galvanic isolation between the control computer and

the access control network. This promotes improved multi-drop RS485 networking performance and

the reduction in possible ground loop communication errors.

Power Source

The USB-485-ISO-TB Adapter derives its power source from the standard USB port it is connected to.

It does not require any additional power sources. This interface consists of two parts, the USB

Connector Cable with 6 coloured terminations and the Interface Circuit Board. You will need to first

terminate the USB Connector Cable ends to the Interface Circuit Board at the fixed miniature 6-way

USB Lead terminal connections. The main access control network is connected at the Door Network

removable 5-way connector. A small housing is provided with cable strain reliefs to enclose the

terminations.

Connections

The access control network connection will allow the network connection of up to 128 Door Control

Units with single continuous multi-drop door network installation. The connections from the Door

Network output to the first control unit and on to the next are shown below:

Network Adapter First Control Unit Next Control Unit…

T+ T+ T+

T- T- T-

R+ R+ R+

R- R- R-

G (Screen) G (Screen) G (Screen)

Two LED’s are embedded in the USB connector body. When at least one door is defined and the

system software is actively communication with the door(s) then the Red LED indicates a

transmission to the door network and the Green LED a reply. With these LED’s and the 'Online LED' in

each Door Control Unit any network cabling errors can be easily diagnosed and remedied.

Additionally, there are two jumper links (LK1 & LK2) on the Interface Circuit Board which provide

receive channel input bias. These should always be connected as supplied.

Interface Commissioning

The adapter software driver must be installed prior to the connection of the device to your PC. The

application driver software is installed automatically when you fully install the Access Control

Software Suite application which is available to download from our website. You can also download

a separate stand alone installer of the driver if you wish. Once all the network connections have been

terminated and the software or device driver has been installed you are ready to plug in the adapter

to a spare USB port on your PC. Once the device is recognised messages on your screen will prompt

you on the progress of the automatic configuration of this adapter. If the software or driver has been

installed correctly prior to the physical connection then this will result in your PC informing you that

“The device has been installed correctly” or similar. If you have fully installed the Access Control

Software Suite, the adapter should be detected automatically and no further configuration is needed.

USB-485-RPI-TB Boxed Network Adapter Interface

Best results will be achieved when following these instructions as they describe the installation and

best practice for this adapter product. The USB-485-RPI-TB Adapter has been designed to simplify

the connection of a single, multi-drop cluster or complete network of Door Control Units. You can

use this product to connect the control computer to up-to 128 Door Control Units by deploying one

adapter. This device is supplied with an internal composite housing complete with cable entry ports.

Power Source

The USB-485-RPI-TB Adapter requires a 12VDC power source usually derived from the first Door

Control Unit (back-powered) it is connected too. It does not normally require any other external

power sources and the device is reverse polarity protected but correct polarisation is required for

operation.

Connections

You can only connect a single segment of Door Control Units to one USB-485-RPI-TB Adapter. The

connections for the adapter to the first control unit and on to the next are shown below:

Network Adapter First Control Unit Next Control Unit…..

12 + no connection

T+ T+ T+

T- T- T-

R+ R+ R+

R- R- R-

G G (Screen) G (Screen)

Interface Commissioning

The adapter software driver must be installed prior to the connection of the device to your PC. The

application driver software is installed automatically when you fully install the Access Control

Software Suite application which is available to download from our website. You can also download

a separate stand alone installer of the driver if you wish, but this is not necessary if you are or have

installed the Access Control Software Suite. Once all the network connections have been terminated

and the software or device driver has been installed you are ready to plug in the adapter to a spare

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Controllori di accesso IP popolari di altre marche

ZKTeco

ZKTeco SpeedFace-V5L Manuale utente

Jantar

Jantar REX A-1-9 Manuale utente

2N Access Unit Foglio di istruzioni

Kedacom

Kedacom KSCA120 Series Manuale utente

H3C

H3C WX2880X Manuale utente

G4S

G4S S870-EX Guida

PRASTEL

PRASTEL M2000PE Manuale utente

Allegion

Allegion interflex IF-281 Cylinder Manuale utente

TECOM

TECOM TS1067E Manuale utente

Fermax

Fermax Memokey 100C Guida utente

Fermax

Fermax CITYLINE MEMOKEY Manuale di istruzioni

Software House

Software House iSTAR Pro 2U RM Manuale di istruzioni

AKCP

AKCP SP+ Manuale utente

Bpt

Bpt HNA/102 Manuale utente

Civintec

Civintec CV9601T-T-1F Manuale utente

BioMax

BioMax N-X90W Manuale utente

ZKTeco

ZKTeco OP-200 Manuale utente

FingerTec

FingerTec s-Kadex Manuale utente