Ssl CLZMF Manuale del proprietario

CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

TG-TD-092623

CLZMF

t800.900.1730

3609 Swenson Ave.

St. Charles, IL 60174

DETAILED ILLUSTRATION

©SOLID STATE LUMINAIRES.

Fig 1

GENERAL:

1. Before starting the installation, make sure all electricity has

been turned off and electrical breaker has been locked out

and tagged out.

2. To ensure the success of the installation, be sure to read

these instructions and review the diagrams thoroughly

before beginning.

3. All electrical connections must be in accordance with local

codes, ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing in

this manual are not meant to cover all possible conditions and

situations that may occur.

INSTALLATION:

Recommended: Due to the weight of the luminaire it is

recommended to use two installers for safe handling.

1. Identify all parts are present for assembly and use a sturdy

surface to complete assembly. Fig 1

2. Prepare end bolts for assembly by placing the Split

Washer on the bolt. Fig 2

3. Re-Insert the end-bolts onto the housing and hand-tighten.

4. Using the arrows located on side of luminaire, adjust beam

target. Fig 3

5. Once desired angle is reached, Tighten to 90 IN-LBS with

a 5 mm hex

WARNING: Failure to tighten luminaire to an adequate torque

value will result 3G vibration Failure.

Fig 2

Fig 3

Loctite 271

5 MM

END BOLT

SPLIT-WASHER

BIT TYPE: 5 MM

TIGHTEN TO 90 IN-LBS

SPLIT-WASHER

LOCTITE 271

APPLY LOCTITE HERE

BETWEEN MEASUREMENTS

0.75 inch

1.10 inches

USE ARROWS ON

SIDE OF LUMINIAIRE

TO ADJUST ANGLE

BEFORE TIGHTENING

CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

TG-TD-092623

CLZMF

t800.900.1730

3609 Swenson Ave.

St. Charles, IL 60174

DETAILED ILLUSTRATION

©SOLID STATE LUMINAIRES.

DRIVE SIZE: 2.5 MM

TORQUE: 15 IN-LBS

2.5 MM

DRIVE SIZE: 2.5 MM

TORQUE: 15 IN-LBS

2.5 MM

DRIVE SIZE: 2.5 MM

TORQUE: 15 IN-LBS

2.5 MM

Fig 1

GENERAL:

1. Before starting the installation, make sure all electricity has been

turned off and electrical breaker has been locked out and tagged out.

2. To ensure the success of the installation, be sure to read these

instructions and review the diagrams thoroughly before beginning.

3. All electrical connections must be in accordance with local codes,

ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing in this

manual are not meant to cover all possible conditions and situations

that may occur.

INSTALLATION:

FULL VISOR (FV)

1. Place the Full Visor over the top of the Micro Flood luminaire and align

the four holes in the Visor with the four screw holes on the luminaire.

Fig 1

2. Fasten the Full Visor down onto the Micro Flood luminaire using the

four provided screws. Tighten evenly alternating opposite sides. Fig 2

HALF VISOR (HV)

IMPORTANT: Ensure you’re installing the Half Visor with the high side

on the appropriate side of the luminaire for the intended light cutoff.

1. Place the Half Visor over the top of the Micro Flood luminaire and align

the four holes in the Visor with the four screw holes on the luminaire.

Fig 3

2. Fasten the Half Visor down onto the Micro Flood luminaire using the

four provided screws. Tighten evenly alternating sides. Fig 4

ROCK GUARD (RG)

IMPORTANT: Ensure you’re installing the Rock Guard so that the

optics line up in between the guard slats to prevent light cutoff.

1. Place the Rock Guard over the top of the Micro Flood luminaire and

align the four holes in the Visor with the four screw holes on the

luminaire. Fig 3

2. Fasten the Rock Guard down onto the Micro Flood luminaire using the

four provided screws. Tighten evenly alternating sides. Fig 4

Fig 3

Full Visor (FV) Half Visor (HV)

Fig 5

Rock Guard (RG)

Fig 2 Fig 4 Fig 6

CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

TG-TD-092623

CLZMF

t800.900.1730

3609 Swenson Ave.

St. Charles, IL 60174

DETAILED ILLUSTRATION

©SOLID STATE LUMINAIRES.

Fig 1 All Connections on Back of Luminaire

GENERAL:

1. Before starting the installation, make sure all electricity

has been turned off and electrical breaker has been

locked out and tagged out.

2. To ensure the success of the installation, be sure to read

these instructions and review the diagrams thoroughly

before beginning.

3. All electrical connections must be in accordance with

local codes, ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing

in this manual are not meant to cover all possible conditions

and situations that may occur.

INSTALLATION:

1. Once the Modules and Bracket Arms have been

assembled and bolted into place, the next step is to run

power and data lines to and from the luminaire modules.

2. All connections to and from the modules are made on

the bottom of the luminaires. Fig 1

IMPORTANT: Maximum Units in a Run: 9 Modules (120V)

REQUIRED: Starter Cable (SCxxCLZ) and Terminator Cap

(TCAPDCLZ) are required for every run.

ColourLine Lazer — Basic Luminaire Wiring

STARTER CORD (SCxxCLZ)

Required Started Cord comes with a luminaire connector at one

end and lead wires at the other end for connecting power & data.

EXTENSION CORD (ECxxCLZ)

The Extension Cord comes with a luminaire connection at each

end for connecting power & data.

TERMINATOR CAP (TZCAPDCLZ)

Required Started Cord comes with a luminaire connector at one

end and lead wires at the other end for connecting power & data.

10, 25, or 50 feet

24, 60 120, or 240 inches

120 Oh

Resister

CONNECTION ARE MADE HERE.

CONNECT TO EITHER SIDE, BOTH

CONNECTORS ARE THE SAME.

CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

TG-TD-092623

CLZMF

t800.900.1730

3609 Swenson Ave.

St. Charles, IL 60174

DETAILED ILLUSTRATION

©SOLID STATE LUMINAIRES.

GENERAL:

1. Before starting the installation, make sure all electricity

has been turned off and electrical breaker has been

locked out and tagged out.

2. To ensure the success of the installation, be sure to read

these instructions and review the diagrams thoroughly

before beginning.

3. All electrical connections must be in accordance with

local codes, ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing

in this manual are not meant to cover all possible conditions and

situations that may occur.

INSTALLATION:

1. Verify Physical Layout Plan

a. Ensure all luminaires, components and wiring hardware are

present before starting installation.

b. Fasten the luminaires and other components in place.

c. Run wire cable and complete connections as indicated

in the diagrams to the right.

2. All connections to and from the modules are made on

the bottom of the luminaires.

HARDWARE: May include RDM Controller, Exterior Rated

Data Line, AC Power Feed, PDX/S box, PDX box, Starter

Cords, Terminator Caps, Extension Cables and luminaires.

NOTE: Use Extension Cable when necessary, for corners

and extending luminaire runs.

IMPORTANT: Maximum Units in a Run: 9 Modules (120V)

REQUIRED: Starter Cable (SCxxCLZ) and Terminator Cap

(TCAPDCLZ) are required for every run.

ColourLine Lazer — Basic Component Congurations

Component Identication

1) DMX Color Controller (see last page)

2) DMX Data Cable DXC-xx or CD-xx (CSC only)

3) PDX Power Data Wiring Box

4) Starter Cord SCxxCLZ

5) ColourLine Lazer (CLZMF)

6) Extension Cord ECxxCLZ (connect at back

of luminaire)

7) Connected ColourLine Lazer Micro (CLZMF)

8) Extension Cords connect luminaires ECxxCLZ

9) Terminator Cap TCAPDCLZ (required at end of run)

10) Maximum Units in a Run (before adding more power):

9Modules (120V),18 Modules (277V)

Back of Luminaire Connections

Connect to either side, both

connectors are the same.

Back of Luminaire Connections

Maximum Units in a Run = 9 Modules (120V)

J-Box

CTRL

(Underneath)

Terminator Ca

Required to

End Each Run

CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

TG-TD-092623

CLZMF

t800.900.1730

3609 Swenson Ave.

St. Charles, IL 60174

DETAILED ILLUSTRATION

©SOLID STATE LUMINAIRES.

DMX/RDM

Controller

Extension Cord (ECxxCLZ)

(xx = 24, 60, 120, or 240 inches)

Starter Cord (SCxxCLZ)

(xx = 10, 25, or 50 feet)

End Run with

Terminator Cap

(TCAPDCLZ)

AC Input

(120-277V)

AC Input

(120-277V)

Extension Cord (ECxxCLZ)

(xx = 24, 60, 120, or 240 inches)

Starter Cord (SCxxCLZ)

(xx = 10, 25, or 50 feet)

End Run with

Terminator Cap

(TCAPDCLZ)

AC Input

(120-277V)

To Next

PDX2/S

(

(12

GENERAL:

1. Before starting the installation, make sure all electricity has been

turned off and electrical breaker has been locked out and tagged out.

2. To ensure the success of the installation, be sure to read these

instructions and review the diagrams thoroughly before beginning.

3. All electrical connections must be in accordance with local codes,

ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing in this

manual are not meant to cover all possible conditions and situations

that may occur.

INSTALLATION:

1. Verify Physical Layout Plan

a. Ensure all hardware is present.

b. Ensure all electrical feeds are correctly positioned with all

hardware and any other active components.

c. Conrm DMX Addressing Plan

i. SSL recommends pre-addressing xtures before

mounting installation.

ii. Ensure that addressing is documented for future

upgrading, conguring or troubleshooting.

HARDWARE: May include RDM Controller, Exterior Rated

Data Line, AC Power Feed, PDX-S box, PDX2 box, Starter

Cords, Terminator Caps, Extension Cables and xtures.

NOTE: Use Extension Cable when necessary, for corners and

extending xture runs.

IMPORTANT: Maximum Units in a Run: 9 Modules (120V)

REQUIRED: Starter Cable (SCxxCLZ) and Terminator Cap

(TCAPDCLZ) are required for every run.

CLZMF RGBW — Multiple Segment Conguration

STARTER CORD (SCxxCLZ) TERMINATOR CAP (TZCAPDCLZ)

120 Oh

Resister

6-Pin Connectors

2.4 inches

3 Data (-)

2 Data (+)

1 G

CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

TG-TD-092623

CLZMF

t800.900.1730

3609 Swenson Ave.

St. Charles, IL 60174

DETAILED ILLUSTRATION

©SOLID STATE LUMINAIRES.

GENERAL:

1. Before starting the installation, make sure all electricity has

been turned off and electrical breaker has been locked out

and tagged out.

2. To ensure the success of the installation, be sure to read

these instructions and review the diagrams thoroughly

before beginning

3. All electrical connections must be in accordance with local

codes, ordinances, or the National Electrical Code.

NOTE: The important safeguards and instructions appearing in

this manual are not meant to cover all possible conditions and

situations that may occur.

INSTALLATION:

1. PDX2 (Power/ Data Box)

a. Mount PDX2 (PDX2 is exterior-rated).

NOTE: Use appropriate fasteners (#10 screws) for mounting to

surface type.

PDX2 — Power/Data Box

BLACK — LINE

WHITE — NEUTRAL

GREEN — GROUND

PURPLE — DATA+

PINK — DATA-

Cable Accessories (order separately)

Accessories (Indicate the quantity needed for each item.) REQUIRED: Starter Cable (SCxxCLZ) and Terminator Cap (TCAPDCLZ) for every run.

SC10CLZ 10 feet Starter Connection Cord

SC25CLZ 25 feet Starter Connection Cord

SC50CLZ 50 feet Starter Connection Cord

TCAPDCLZ Data Terminator Cap (120 Ohm)

EC24CLZ 24 inches Extension Cord

EC60CLZ 60 inches Extension Cord

EC120CLZ 120 inches Extension Cord

EC240CLZ 240 inches Extension Cord

3.6 inches

7.4 inches

3.8 inches

6.6 inches

6.1 inches

7.8 inches

4.8 inches

6.8 inches

Top View

Front View Side View

Use

(4) #10

Screws

CLZMF — INSTALL INFORMATION AND OPERATION INSTRUCTIONS

CAUTION: BEFORE CONNECTING THE LUMINAIRE TO A POWER SUPPLY, MAKE SURE THE POWER IS SWITCHED OFF.

TG-TD-092623

CLZMF

t800.900.1730

3609 Swenson Ave.

St. Charles, IL 60174

DETAILED ILLUSTRATION

GENERAL:

1. Before starting the installation, make sure all

electricity has been turned off and electrical

breaker has been locked out and tagged out.

2. To ensure the success of the installation, be sure

to read these instructions and review the diagrams

thoroughly before beginning.

3. All electrical connections must be in accordance

with local codes, ordinances, or the National

Electrical Code.

NOTE: The important safeguards and instructions

appearing in this manual are not meant to cover all

possible conditions and situations that may occur.

INSTALLATION:

1. PDX2 (Power/ Data Box)

a. Mount PDX2 (PDX2 is exterior-rated).

NOTE: Use appropriate fasteners (#10 screws) for mounting

to surface type.

b. PDX2 Wiring Diagram

PDX2 — Power/Data Box

Ground (G)

Neutral (N)

Line (L)

AC Power (IN)

Shield

(+) Data (Purple)

(–) Data (

Pink or Gray)

Ground (G)

Neutral (N)

Line (L)

Fixture (OUT)

TOP VIEW

DMX Controller (IN)

Wire Shield

Shield

Data (+) (Blue w/ White Dash)

Data (–) (White w/

Blue Dash)

PDX2 Wiring

BLACK — LINE

WHITE — NEUTRAL

GREEN — GROUND

PURPLE — DATA+

PINK — DATA-

Indice

Altri manuali Ssl Attrezzatura di illuminazione

Ssl

Ssl ColourLine LazerLine Wet Manuale del proprietario

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente