ST X-NUCLEO-53L8A1 Manuale utente
Introduction
The X-NUCLEO-53L8A1 is an expansion board for any STM32 Nucleo development board equipped with the Arduino R3
connectors. It provides a complete evaluation kit that allows you to learn, evaluate, and develop applications based on the
VL53L8 series Time-of-Flight sensors.
The expansion board is delivered with a cover glass holder in which you can fit three different spacers of 0.25, 0.5, and 1 mm
height below the cover glass to simulate various air gaps. A small oval cover glass fitting the sensor is included.
Several ST expansion boards can be stacked through the Arduino connectors, which allow, for example, the development of
VL53L8 applications with Bluetooth or Wi-Fi interfaces.
Figure 1. X-NUCLEO-53L8A1 expansion board, spacers, cover glass holder, and oval cover glass
Getting started with the X-NUCLEO-53L8A1 Time-of-Flight expansion board
based on the VL53L8 series for STM32 Nucleo
UM3120
User manual
UM3120 - Rev 1 - March 2023
For further information contact your local STMicroelectronics sales office. www.st.com
1Getting started
1.1 Safety considerations
1.1.1 Electrostatic precautions
Warning: Take electrostatic precautions, including ground straps, when using the X-NUCLEO-53L8A1
expansion board. Failure to prevent electrostatic discharge could damage the device.
Figure 2. Electrostatic logo
1.1.2 Laser safety considerations
The VL53L8CX contains a laser emitter and the corresponding drive circuitry.
The laser output is designed to remain within Class 1 laser safety limits under all reasonable foreseeable
conditions, including single faults, in compliance with the IEC 60825-1:2014.
The laser output power must not be increased by any means and no optics should be used with the intention of
focusing the laser beam.
Caution: Use of controls or adjustments, or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
Figure 3. Class 1 laser product label
Figure 4. Laser notice 56: applies to IEC 60825-1:2014
1.2 Features
•VL53L8CX, low-power, high performance 8x8 multizone Time of-Flight sensor
• Hideable behind a dark cover window
• Accurate absolute ranging distance, independent of the reflectance of the target
• Up to 400 cm ranging
UM3120
Getting started
UM3120 - Rev 1 page 2/23
• Histogram-based technology
• I²C (up to 1 MHz) or SPI (up to 20 MHz) interface
• Multiobject detection capability
• 0.25, 0.5, and 1 mm spacers to simulate air gaps
• One cover glass to protect the sensor from dust
• Compatible with STM32 Nucleo development boards
• Equipped with Arduino UNO R3 connectors
• Full system software supplied, including code examples and graphical user interface
• RoHS, CE, UKCA, and China RoHS compliant
1.3 VL53L8 series Time-of-Flight sensor characteristics
• Laser wavelength : 940 nm
• Invisible laser radiation
• Maximum laser power emitted : 215 mW
• Integration time : 2 ms minimum
1.4 Spacers and covers
The X-NUCLEO-53L8A1 expansion board is delivered with:
• three spacers of 0.25 mm, 0.5 mm, and 1 mm height, used to simulate different air gaps between the
VL53L8 and the rectangular-shaped cover glass;
• two twelve-pin headers that allow connecting the two mini PCB of the SATEL boards to the X-
NUCLEO-53L8A1 expansion board through flying wires.
Attention: The VL53L8 is delivered with a liner to prevent potential foreign material from piercing the module holes during
the assembly process. Remove this liner before use.
1.5 Ordering information
Table 1. Ordering information
Order code PCB version Core product
X-NUCLEO-53L8A1A X$NUCLEO-53L8A1A VL53L8
1.6 Ordering information for the VL53L8 series Time-of-Flight sensors
This board is equipped with a noncommercial VL53L8CA evaluation purposes only Time of Flight sensor. Its
equivalent orderable products are listed in the following table. For a detailed description of each sensor, please
refer to its datasheet on the product web page. Additional information is available from the user manual and
collateral documents of the target ToF sensor.
Table 2. VL53L8 series ordering information
RPN CPN Datasheet Features
VL53L8CX VL53L8CXV0GC/1 DS14161 Low-power high-performance 8x8
multizone Time-of-Flight
UM3120
VL53L8 series Time-of-Flight sensor characteristics
UM3120 - Rev 1 page 3/23
2Using the expansion board
The X-NUCLEO-53L8A1 expansion board allows the user to test the VL53L8 sensor functionality, to program it
and to understand how to develop an application using this sensor.
The X-NUCLEO-53L8A1 integrates:
• the VL53L8 sensor;
• Arduino UNO R3 connectors;
• Connectors for SATEL-VL53L8 optional breakout boards;
Important: Program a microcontroller to control the VL53L8CX through the I2C bus.
The application software and an example of the C-ANSI source code are available on the sensor web page.
The X-NUCLEO-53L8A1 expansion board can be connected to the STM32 Nucleo development board through
the Arduino UNO R3 connectors (CN5, CN6, CN8, and CN9).
I²C (up to 1 MHz) and SPI (up to 20 MHz) interfaces are available on the X-NUCLEO-53L8A1 expansion board.
The user can choose between the two using the J9 jumper to configure the SPI_I2C_N signal as depicted in the
following picture.
Figure 5. Use onboard jumper J9 to select between I2C and SPI interfaces
UM3120
Using the expansion board
UM3120 - Rev 1 page 4/23
3Breakout boards
The X-NUCLEO-53L8A1 package does not include the VL53L8 breakout boards.
You can purchase them in a pack of two PCBs as SATEL-VL53L8.
For mechanical integration purposes, it could be interesting to use the mini PCB by breaking the SATEL-VL53L8
along the red line as shown in the figure below. It is easier to integrate this setup into a customer's device thanks
to its small size.
Figure 6. SATEL-VL53L8
The SATEL-VL53L8 boards cannot be directly plugged onto the X-NUCLEO-53L8A1 through the two 6-pin
headers (see Figure 7).
They can be connected to the X-NUCLEO-53L8A1 by using the mini PCB through flying wires (see
Figure 9. VL53L8 mini PCB flying wire connection to the X-NUCLEO-53L8A1 expansion in SPI mode. J9 jumper
with pin 1 and 2 connected).
The schematic can be duplicated for the sensor on the right allowing the use of both mini PCB.
UM3120
Breakout boards
UM3120 - Rev 1 page 5/23
Figure 7. SATEL-VL53L8 breakout boards can not be connected to the X-NUCLEO-53L8A1 expansion
board
Figure 8. VL53L8 mini PCB flying wire connection to the X-NUCLEO-53L8A1 expansion board in I2C
mode. J9 jumper with pin 2 and 3 connected
UM3120
Breakout boards
UM3120 - Rev 1 page 6/23
Figure 9. VL53L8 mini PCB flying wire connection to the X-NUCLEO-53L8A1 expansion in SPI mode. J9
jumper with pin 1 and 2 connected
UM3120
Breakout boards
UM3120 - Rev 1 page 7/23
4Graphical user interface (GUI) and programming example for the
X-NUCLEO-53L8A1
To evaluate the VL53L8 device performance, use the related GUI or the X-CUBE-TOF1.
The X-NUCLEO-53L8A1 expansion board requires the NUCLEO-F401RE development board to use the GUI or
run the ranging examples included in the X-CUBE-TOF1.
Important: Despite the fact that the X-NUCLEO-53L8A1 can be stacked on any STM32 Nucleo board equipped the Arduino
R3 connectors, the GUI is designed to work with the NUCLEO-F401RE only.
Download the GUI (in the Tools and Software tab of the X-NUCLEO-53L8A1 web page) or the X-CUBE-TOF1 to
evaluate the VL53L8.
UM3120
Graphical user interface (GUI) and programming example for the X-NUCLEO-53L8A1
UM3120 - Rev 1 page 8/23
5Schematic diagrams
Note: These schematic diagrams refer to the board latest version.
Figure 10. X-NUCLEO-53L8A1 circuit schematic (1 of 5)
MISO
MOSI_SDA
NCS
MCLK_SCL
GPIO1
GPIO2
LPn
SPI_I2C_N
Sensor
Sensor.SchDoc
MCLK_SCL
SPI_I2C_N
PWR_EN
NCS
GPIO1
GPIO2
MOSI_SDA
MISO
LPn
Right
Satellite_Connector.SchDoc
MOSI_SDA
GPIO1
MCLK_SCL
GPIO2
IO_MCLK_SCL
IO_MOSI_SDA
MISOIO_MISO
NCSIO_NCS
IO_LPn LPn
IO_GPIO1
IO_GPIO2
IO_LPn_LEFT
IO_GPIO1_RIGHT
IO_GPIO1_LEFT GPIO1_LEFT
IO_GPIO2_LEFT
LPn_RIGHTIO_LPn_RIGHT
IO_GPIO2_RIGHT
GPIO1_RIGHT
GPIO2_LEFT
LPn_LEFT
GPIO2_RIGHT
NCS_LEFT
NCS_RIGHT
IO_NCS_LEFT
IO_NCS_RIGHT
Level Shifters
Level_Shifters.SchDoc
MCLK_SCL
SPI_I2C_N
PWR_EN
NCS
GPIO1
GPIO2
MOSI_SDA
MISO
LPn
Left
Satellite_Connector.SchDoc
PA1
PA0
PA3
PA4
PA2
PA6
PA5
PA7
PA8
PA10
PA9
PC1
PC0
PC7
PB0
PB10
PB6
PB5
PB4
PB3
PB8
PB9
Host
Host.SchDoc
PWR_EN
Power
Power.SchDoc
3V3
1
2
3
J7
1
2
3
J8
J7[1-2]
J8[1-2]
1
2
3
J9
J9[2-3]
1%
R40
1k
1%
R41
1k
IOVDD
1%
R18
2.2k
1%
R19
2.2k
TP1
TP2
TP3
M4
FIDUCIAL
M3
FIDUCIAL
M2
FIDUCIAL
M1
FIDUCIAL
PWR_EN_Right
PWR_EN_Left
PWR_EN_Sensor
SILK
SPI_I2C_N
[1-2] : SPI
[2-3] : I2C
GND1
Clip
GND2
Clip
M6
FIDUCIAL
M5
FIDUCIAL
One jumper for all devices
SILK
[1-2] : I2C
[2-3] : SPI
Note: The display connector is an optional connector to connect an SSD1306 I2C OLED display to output the ranging data or other meaningful information if
required. The related application note and example code will be available on st.com.
UM3120 - Rev 1 page 9/23
UM3120
Schematic diagrams
Figure 11. X-NUCLEO-53L8A1 circuit schematic (2 of 5)
3V3_NUCLEO5V_NUCLEO
PB8
PB9
PC7
PB10
PB4
PB5
PA10
PA2
PA3
PA1
PA0
PA4
PB0
PC1
PC0
PA9
PB6
PA7
PA6
PA5
PB3
PA8
1
2
3
4
5
6
7
8
CN6
1
2
3
4
5
6
7
8
9
10
CN5
2.54mm, T/H, Vert
1
2
3
4
5
6
7
8
CN9
2.54mm, T/H, Vert
1
2
3
4
5
6
CN8
2.54mm, T/H, Vert
Nucleo Arduino connectors
HDR 8x1 Male 2.54mm
UM3120 - Rev 1 page 10/23
UM3120
Schematic diagrams
Altri manuali per X-NUCLEO-53L8A1
1
Indice
Altri manuali ST Hardware per computer
ST
ST X-NUCLEO-OUT02A1 Manuale utente
ST
ST STM32F405 Series Manuale utente
ST
ST 32F412GDISCOVERY Manuale utente
ST
ST MB467 Manuale utente
ST
ST EVSPIN948 Manuale utente
ST
ST X-NUCLEO-AMICAM1 Manuale utente
ST
ST STEVAL-IDB013V1 Guida per l'amministratore
ST
ST X-NUCLEO-OUT14A1 Manuale utente
ST
ST X-NUCLEO-IHM12A1 Manuale utente
ST
ST X-NUCLEO-53L3A2 Manuale utente
ST
ST X-NUCLEO-OUT07A1 Manuale utente
ST
ST STEVAL-MIC008A Manuale utente
ST
ST STM32 Nucleo Manuale utente
ST
ST STR9 Manuale utente
ST
ST X-NUCLEO-SAFEA1B Istruzioni operative
ST
ST X-NUCLEO-IHM08M1 Manuale utente
ST
ST X-NUCLEO-LED12A1 Manuale utente
ST
ST AN1235 Istruzioni per l'installazione e il funzionamento
ST
ST X-CUBE-OUT3 Manuale utente
ST
ST X-NUCLEO-IOD02A1 Manuale utente
Manuali Hardware per computer popolari di altre marche
EMC2
EMC2 VNX Series Manuale del proprietario
Panasonic
Panasonic DV0PM20105 Manuale utente
Mitsubishi Electric
Mitsubishi Electric Q81BD-J61BT11 Manuale utente
Gigabyte
Gigabyte B660M DS3H AX DDR4 Manuale utente
Raidon
Raidon iT2300 Manuale utente
National Instruments
National Instruments PXI-8186 Manuale utente
