ST X-NUCLEO-IHM04A1 Manuale utente

Chipsmall Limited consists of a professional team with an average of over 10 year of expertise in the distribution

of electronic components. Based in Hongkong, we have already established firm and mutual-benefit business

relationships with customers from,Europe,America and south Asia,supplying obsolete and hard-to-find components

to meet their specific needs.

With the principle of “Quality Parts,Customers Priority,Honest Operation,and Considerate Service”,our business

mainly focus on the distribution of electronic components. Line cards we deal with include

Microchip,ALPS,ROHM,Xilinx,Pulse,ON,Everlight and Freescale. Main products comprise

IC,Modules,Potentiometer,IC Socket,Relay,Connector.Our parts cover such applications as commercial,industrial,

and automotives areas.

We are looking forward to setting up business relationship with you and hope to provide you with the best service

and solution. Let us make a better world for our industry!

Tel: +86-755-8981 8866 Fax: +86-755-8427 6832

Email & Skype: [email protected]om Web: www.chipsmall.com

Address: A1208, Overseas Decoration Building, #122 Zhenhua RD., Futian, Shenzhen, China

  

August 2015

DocID028121 Rev 1

1/17

www.st.com

UM1925

User manual

Getting started with the X-NUCLEO-IHM04A1 dual brush DC

motor driver expansion board for STM32 Nucleo

Introduction

The X-NUCLEO-IHM04A1 is a dual brush DC motor drive expansion board based on L6206 (DMOS

dual full bridge driver) to drive dual bipolar DC or quad unipolar DC motors. It provides a low cost,

robust and easy-to-use solution for driving DC motors in your STM32 Nucleo project. A flexible solution

for driving 1 to 4 DC motors is implemented via jumpers.

The X-NUCLEO-IHM04A1 is compatible with the Arduino UNO R3 connector, and supports the addition

of other expansion boards with a single STM32 Nucleo board. The user can also mount the ST Morpho

connector.

Figure 1: X-NUCLEO-IHM04A1: Dual brush DC motor driver expansion board based on L6206

Contents

UM1925

2/17

DocID028121 Rev 1

Contents

1Getting started................................................................................3

2Hardware description and configuration ......................................4

2.1 overcurrent (OCD) threshold setting ................................................5

2.2 Selecting the mode ..........................................................................6

2.2.1 Mode no. 1: two bidirectional DC motors ..........................................7

2.2.2 Mode no. 2: four DC motors unidirectional........................................7

2.2.3Mode no. 3: parallel connection for higher current - one DC motor

bidirectional .......................................................................................................8

2.2.4 Mode n °4: parallel connection for higher current - two unidirectional

DC motors .........................................................................................................9

2.2.5 Mode no. 5: parallel connection for lower overcurrent - one DC

motor bidirectional...........................................................................................10

2.2.6 Mode n °6: parallel connection for lower overcurrent - two

unidirectional DC motors.................................................................................11

2.2.7 Mode no. 7: parallel all bridges - one unidirectional DC motor .......12

3Schematic diagram....................................................................... 13

4Bill of material............................................................................... 14

5Revision history ........................................................................... 16

UM1925

Getting started

DocID028121 Rev 1

3/17

1 Getting started

The X-NUCLEO-IHM04A1 expansion board is a dual brush DC motor driver covering a

wide range of applications. The maximum ratings of the board are the following:

Power stage supply voltage (VS) from 8 V to 50 V

Motor phase current up to 2.8 A r.m.s.

Follow this sequence to start your project with the board:

1. Check the jumper position based on your configuration (see Section 2: "Hardware

description and configuration")

2. Connect the board with the STM32 Nucleo board through Arduino UNO R3 for the X-

NUCLEO-IHM04A1

3. Supply the board through the input 6 (VS) and 5 (ground) of the connector CN1

4. Develop your application using the examples provided with the firmware library, X-

CUBE-SPN4

Further support material is available on the L6206 and the STM32 Nucleo web pages on

www.st.com

Hardware description and configuration

UM1925

4/17

DocID028121 Rev 1

2 Hardware description and configuration

Figure 2: Jumper and connector position

The following table provides the detailed pinout of the Arduino UNO R3 and ST Morpho

connectors.

Table 1: Arduino UNO R3 connector table

Connector

Pin (1)

Signal

Remarks

CN5

ADC-6

Ground

CN9

EN-A

IN2A

See Section 2.1:

"overcurrent (OCD)

threshold setting"

IN1A

See Section 2.1:

"overcurrent (OCD)

threshold setting"

CN6

Ground

CN8

IN1B

See Section 2.1:

"overcurrent (OCD)

threshold setting"

IN2B

See Section 2.1:

"overcurrent (OCD)

threshold setting"

ADC-4

Notes:

(1)All the non-listed pins are not connected.

UM1925

Hardware description and configuration

DocID028121 Rev 1

5/17

Table 2: ST Morpho connector table

Connector

Pin (1)

Signal

Remarks

CN10

Ground

ADC-6

IN1A

See Section 2.1:

"overcurrent (OCD)

threshold setting"

IN2A

See Section 2.1:

"overcurrent (OCD)

threshold setting"

EN-A

CN7

Ground

IN1B

See Section 2.1:

"overcurrent (OCD)

threshold setting"

IN2B

See Section 2.1:

"overcurrent (OCD)

threshold setting"

ADC-4

EN-B

Notes:

(1)All the non-listed pins are not connected.

2.1 overcurrent (OCD) threshold setting

The device integrates two overcurrent protection circuits with adjustable threshold, one for

each full bridge.

The overcurrent threshold is set through the R9 (bridge A) and R8 (bridge B) resistors, as

indicated in Figure 3: "Overcurrent threshold versus resistor value (no paralleling)".

Hardware description and configuration

UM1925

6/17

DocID028121 Rev 1

Figure 3: Overcurrent threshold versus resistor value (no paralleling)

When one of the paralleling modes is used (see Section 2.2: "Selecting the mode"), the

actual OCD threshold value may be scaled as indicated in Table 1: "Arduino UNO R3

connector table".

2.2 Selecting the mode

This board can drive 1 to 4 DC motors with several configurations.

The selection is done by Jumper J1 - J2 - J3 and J4, by default: all jumpers are not

populated.

The table below briefly summarizes the possible configurations:

Table 3: Board configuration summary

Mode

Max output

current

Output

RDS(on)

OCD

threshold

scaling

Two bidirectional DC

motors

2.8 A rms

0.3 Ω

× 1

Disconnect

Four unidirectional

DC motors

2.8 A rms (1)

0.3 Ω

× 1 (1)

Disconnect

High current parallel

one bidirectional DC

motor

5.6 A rms

0.15 Ω

× 2

Disconnect

Connected

High current parallel

two unidirectional DC

motors

5.6 A rms

0.15 Ω

× 2

Disconnect

Connected

Low current parallel

one DC motors

bidirectional

2.8 A rms

0.15 Ω

× 1

Connected

Disconnect

Low current parallel

two unidirectional DC

motors

2.8 A rms

0.15 Ω

× 1

Connected

Disconnect

UM1925

Hardware description and configuration

DocID028121 Rev 1

7/17

Mode

Max output

current

Output

RDS(on)

OCD

threshold

scaling

Parallel all bridges

one unidirectional DC

motor

11.2 A rms

0.075 Ω

× 4

Connected

Notes:

(1)The current limit is shared between the two motors connected on the same full-bridge (A or B).

2.2.1 Mode no. 1: two bidirectional DC motors

Two independent DC motors are driven by the board.

The supply voltage of both motors is connected to J1 pin 5 and 6 with a maximum voltage

at 50 V DC.

Maximum current is 2.8 A rms and the output RDS(on) is equal to 0.3 W (TJ= 25 °C).

The maximum overcurrent detection threshold is set to 5.6 A.

Motor A connected between A+ (CN1 pin1) and A- (CN1 pin2)

Motor B connected between B+ (CN1 pin4) and B- (CN1 pin3)

Table 4: Jumper selection

Disconnected

Figure 4: two bidirectional DC motors

2.2.2 Mode no. 2: four DC motors unidirectional

Four independent DC motors are driven by the board.

The supply voltage of both motors is connected to J1 pin 5 and 6 with a maximum voltage

of 50 V DC.

Hardware description and configuration

UM1925

8/17

DocID028121 Rev 1

Maximum current is 2.8 A rms and the output RDS(on) is equal to 0.3 W (TJ= 25 °C).

The maximum overcurrent detection threshold is set to 5.6 A.

The total rms current flowing in A+ and A- DC motor must be below the 2.8 A

rms limit. The OCD threshold is also triggered when the sum of the two output

currents exceeds the programmed threshold.

The same for the B+ and B- outputs.

Motor A connected between A+ (CN1 pin1) and GND

Motor B connected between A- (CN1 pin2) and GND

Motor C connected between B+ (CN1 pin4) and GND

Motor D connected between B- (CN1 pin3) and GND

Table 5: Jumper selection

Disconnected

Figure 5: Four unidirectional DC motors

2.2.3 Mode no. 3: parallel connection for higher current - one DC motor

bidirectional

This mode, with output power in parallel, increases the output current capability.

The motor supply voltage is connected to J1 pin 5 and 6 with a maximum voltage of 50 V

DC.

Maximum current is 5.6 A rms and the output RDS(on) is equal to 0.15 W (TJ= 25 °C).

The maximum overcurrent detection threshold is set to 11.2 A.

Motor A connected between

UM1925

Hardware description and configuration

DocID028121 Rev 1

9/17

Both A+ (CN1 pin1) B+ (CN1 pin4)

Both A- (CN1 pin2) B- (CN1 pin3)

Table 6: Jumper selection

Disconnected

Connected

Figure 6: One DC motor bidirectional - higher current

2.2.4 Mode n °4: parallel connection for higher current - two unidirectional

DC motors

This mode is similar to mode 3 - the bidirectional DC motor is replaced by two

unidirectional DC motors

Motor A connected between

Both A+ (CN1 pin1) B+ (CN1 pin4)

GND

Motor B connected between

Both A- (CN1 pin2) B- (CN1 pin3)

GND

Table 7: Jumper selection

Disconnected

Connected

Indice

Altri manuali ST Hardware per computer

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente

Advantech

Advantech ASMB-935 Series Manuale utente