Stanley GW1200 Manuale utente
GW1200
GATEWAY
INSTALLATION & CONFIGURATION GUIDE
Disclaimer
The information and know-how included in this document are the exclusive property of STANLEY Healthcare and are
intended for the use of the addressee or the user alone The addressees shall not forward to another their right of using
the information, know-how or document forwarded herewith, in whole or in part in all matters relating or stemming from
or involved therein, whether for consideration or without consideration, and shall not permit any third party to utilize the
information, know-how or the documents forwarded herewith or copies or duplicates thereof, unless at the company’s
consent in advance and in writing Any distribution, advertisement, copying or duplication in any form whatsoever is
absolutely prohibited The Company reserves the right to sue the addressee, user and/or any one on their behalves, as
well as third parties, in respect to breaching its rights pertaining to the intellectual rights in particular and its rights of
whatever kind or type in the information, know-how or the documents forwarded by them herewith in general, whether
by act or by omission
This document is confidential and proprietary to STANLEY Healthcare and is not to be distributed to any persons other
than licensed AeroScout Visibility System users or other persons appointed in writing by STANLEY Healthcare
Trademark Acknowledgements
AeroScout is a trademark of Stanley Black & Decker Other brand products and service names are trademarks or
registered trademarks of their respective holders Below is a partial listing of other trademarks or registered trademarks
referenced herein:
Hugs Infant Protection System is a registered trademark of Stanley Black & Decker or its affiliates
Cisco™ is a trademark of Cisco Systems, Inc
Sun, Sun Microsystems, the Sun Logo, Java, JRE and all other Sun trademarks, logos, product names, service names,
program names and slogans that are referred to or displayed in this document are trademarks or registered trademarks
of Sun Microsystems, Inc in the United States and other countries
This product includes software developed by the Apache Software Foundation (http://www apache org/)
This product includes code licensed from RSA Data Security
Skype, SkypeIn, SkypeOut, Skype Me, the Skype Logo and the S logo and other marks indicated on Skype’s website are
trademarks of Skype Limited or other related companies
ESper is a trademark of EsperTech, Inc
Jboss is a trademark of Red Hat Middleware, LLC
Oracle 10G is a registered trademark of Oracle Corporation and/or its affiliates
MS SQL Server is a registered trademark of Microsoft Corporation in the United States and/or other countries
JasperSoft, the JasperSoft Logo, JasperReports, the JasperReports logo, JasperIntelligence, JasperDecisions,
JasperAnalysis, Scope Center, Scope Designer, and JasperServer are trademarks or registered trademarks of JasperSoft,
Inc in the United States and other countries
Warnings
A distance of at least 20 cm between the equipment and all persons should be maintained during the operation of the
equipment
Une distance d'au moins 20 cm entre l'équipement et toutes les personnes devraient être maintenues pendant le
fonctionnement de l'équipement
©2019 STANLEY Healthcare All rights reserved
Doc: 0981-554-000 REV A Published January 2019 KB Article: 10597
Table of
Contents
Table of Contents ........................................................................................................... 3
GW1200 Gateway........................................................................................................... 4
GW1200 Features ........................................................................................................... 5
Wi-Fi Device Detection & Locator 5
Network connectivity 5
Continuous Gateway Supervision 5
Monitoring of Wi-Fi Receivers 5
LED Status In icators ...................................................................................................... 6
Connector Panel ............................................................................................................. 7
Network an Power Connections to the GW1200 Gateway ........................................... 8
Resetting the GW1200 Gateway IP A ress ................................................................. 11
GW1200 Naming Convention ....................................................................................... 12
A ing & Configuring the GW1200 via AeroScout Engine Manager (AEM) .................. 13
Up ating Firmware – Gateways ................................................................................... 14
Mounting the Gateway ................................................................................................ 15
Fixing the Controller to a Floating Ceiling: 15
GW1200 and Accessories Model Numbers 29
GW1200 Specifications ................................................................................................. 30
Regulatory Compliance & Warranty ............................................................................. 31
FCC 31
Industry Canada 31
RoHS 32
CE Conformance 32
Warranty 32
GW1200 Gateway Installation & Configuration Guide
4
GW1200 Gateway
The GW1200 Gateway is a component of STANLEY Healthcare’s suite of solutions based
on Wi-Fi technology, enabling hospital-wide protection of patients and infants
The Gateway is a 2 4 GHz receiver It receives transmission messages from Hugs Wi-Fi
Tags and relays the messages to the Location Engine
The Gateway is used to help provide the core layers of protection – Exit, Tamper, Tag
Loose and Supervision – in either a “Gateway only” deployment with a dedicated
network of Gateways providing Wi-Fi receiver coverage; or with strategically placed
Gateways augmenting the facility’s existing network of Access Points in the desired
protected areas
The Gateway may also be incorporated with additional use cases as determined by
STANLEY Healthcare Engineering
NOTE: The relay outputs are for future functionality and are not currently supported
within MobileView Hugs.
Figure 1: W1200 ateway
GW1200 Gateway Installation & Configuration Guide
5
GW1200 Features
Wi-Fi Device Detection & Locator
The GW1200 Gateway contains two Wi-Fi transceivers for receiving Wi-Fi messages from
802 11 b/g/n (2 4 GHz) Hugs Wi-Fi Tags Received messages are sent to the AeroScout
Location Engine for processing
Network connectivity
The device supports remote programming, monitoring, and software updates by the
AeroScout Location Engine
Continuous Gateway Supervision
The GW1200 Gateway device status is monitored at all times by the AeroScout Location
Engine MobileView generates an alert if communication with the Gateway is
compromised
Additionally, to provide full device supervision capabilities the receiver modules in the
Gateway will switch into a “test transmission mode” simulating Tag message
transmission, to verify reception of each other if no AeroScout tag messages are
received within a 60 second period
Monitoring of Wi-Fi Receivers
The GW1200 Gateway constantly supervises the functionality of its two Wi-Fi receivers
GW1200 Gateway Installation & Configuration Guide
6
LED Status Indicators
The GW1200 Gateway has a single LED that changes color based on the device status as
follows:
•
Constant Green: The Gateway is on and working correctly
•
Constant Orange: Gateway failure or network down
•
No LED indication: Gateway is off
Figure 2: W1200 ateway LED Indicator
GW1200 Gateway Installation & Configuration Guide
7
Connector Panel
The GW1200 Gateway has three connectors on the connector panel
Note
When both PoE and external power supplies are used the external power source
is the primary power source
(#1) Ethernet LAN Connection: RJ-45 connector In a configuration with a physical
Ethernet cable connection to the LAN, the network cable is attached here
The GW1200 supports 100 Mb Full duplex communications The Ethernet Network
Switch must be configured to Auto Negotiation mode for the Gateway to operate at 100
Mb
(#2) Power Jack: Accepts an input voltage of 24-48V DC This is a standard 5 mm (outer)
2 5 mm (internal) jack connector for direct power supply A power adapter is not
supplied with the Controller and can be purchased separately When PoE is used, this
connector becomes redundant
(#3) IN/RS-232 an OUT/RS-232 Connector: RJ-45 connector RS-232 is used as a
console interface with the Exciter Manager Application (to change the IP address, for
example) For this option, a special 10-pin RJ45 to DB9 serial cable (AeroScout PN
40031500000) is required
(#4) IP Reset: Restores the Gateway's IP address to the factory default value
Note
Inputs and Outputs are currently not in use
GW1200 Gateway Installation & Configuration Guide
8
Network and Power
Connections to the GW1200
Gateway
The following is a summary of available power and network options:
Usage Option Description
Single GW1200
Gateway – connected
to a network
GW1200s can be remotely controlled (for configuration and
monitoring purposes) via the local area network In this case,
connect it to both a power source and the network.
GW1200’s support power-over-Ethernet (PoE), which
supplies both power and network services via a single
connection
Power options are 24-48V or PoE
Direct Power Supply
Connect a 24 to 48 VDC power source direct to the Gateway’s power jack
Note
The GW1200 requires approximately 8 W of power When connecting a Gateway to a
direct power source with one of the above options, verify that the provided power
level is sufficient
The device must only be powered by a limited (marked LPS or NEC class 2) power
supply
PoE Switch
If the network has a Power-over-Ethernet infrastructure, a CAT-5/6 Ethernet cable
connects the PoE switch to the Gateway’s LAN connector This supplies both the power
and the network connection
Note
PoE standard 802 3af class 0 allows power for a single GW1200 Gateway
110/220 VAC to 48 VDC PoE Single-Port Injector
The PoE Single Port Injector converts 110/220 VAC to 48 VDC and permits connecting a
single cable from the network to the Gateway’s LAN connector, thus supplying both
power and network connectivity
GW1200 Gateway Installation & Configuration Guide
9
When using this injector, the Gateway power jack is not used
Figure 3: 110/220 VAC to 48VDC PoE Single-Port Injector
The injector’s IN connector is connected to the network The injector’s OUT connector is
connected to the Gateway’s LAN connector
110/220 VAC to 48 VDC Power Supply Adapters
These adapters convert 110 VAC or 220 VAC to 48 VDC
Figure 4: 110/220 VAC to 48 VDC Adapter
The adapter is connected to the GW1200 Gateway power jack The network must be
connected separately to the Gateway LAN connector
GW1200 Gateway Installation & Configuration Guide
10
Power Connection Summary
The following table summarizes the power connection options:
Power Supply Input Output Max.
Current
Available
Power
Maximum # of
Exciters with One
Source
PoE single port
injector
100-240
VAC, 50-
60
Hz
48 VDC 0 32 A(1) 15 4 W One GW1200
Gateway
Standard PoE
802 3af switch
port (2)
– 48 VDC 0 32 A(1) 15 4 W One GW1200
Gateway
External power
adapter
– 48 VDC > 0 4 A > 20 W One GW1200
Gateway
Note
To prevent excessive power loss, PoE cables must not exceed 100 m (330’) in
length
Indice
Altri manuali Stanley Portale
Manuali Portale popolari di altre marche
LST
LST M500RFE-AS Manuale utente
Kinnex
Kinnex Media Gateway Manuale utente
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuale utente
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuale utente
Telsey
Telsey CPVA 500 - SIP Manuale utente
