Star Trac TreadClimber Manuale utente

Assembly & Setup

STAR TRAC FITNESS 1 of 14 635-4175 Rev: B

TreadClimber

INSTALLATION INSTRUCTIONS

Assembly & Setup

STAR TRAC FITNESS 2 of 14 635-4175 Rev: B

NOTICE

Installation of this product requires that 2 or more people are available

to safely perform certain steps outlined by this document.

Assembly & Setup

STAR TRAC FITNESS 3 of 14 635-4175 Rev: B

1. Locate an open area to unbox the packaged

TreadClimber

(Fig.1).

Fig. 1

2. Cut all straps to remove the cardboard packaging along

with any protective wrapping to expose the palletized

TreadClimber base and assembly components (Fig. 2).

Fig. 2

3. Move all unattached components off the TreadClimber

base (Fig. 3).

Components:

A. Console Frame

B. Neck Mast

C. Rear Corner Shroud (Left & Right)

D. Hardware Pack

E. Handrail Grommets

F. Owner’s Manual

G. Neck Grommet

H. Power Cord

I. Rear Shroud

J. Upper Handrails (Left & Right)

K. Lower Handrails (Left & Right)

Fig. 3

Assembly & Setup

STAR TRAC FITNESS 4 of 14 635-4175 Rev: B

4. Breakaway the rear bottom section (Fig. 4) of the

cardboard pallet.

Fig. 4

5. Remove the alternator shroud (Fig. 5) located under

the two treadle assemblies at the front of the

TreadClimber base.

Fig. 5

6. Locate the two transport grip handles (Fig. 6) that come

with the packaged base and attach them to the “J”

hooks located near each front corner of the

TreadClimber base.

Fig. 6

Assembly & Setup

STAR TRAC FITNESS 5 of 14 635-4175 Rev: B

7. With two people, pull the TreadClimber base

backwards (Fig 7) until all four wheels are driven off the

pallet and the base is safely on to the ground.

Fig. 7

8. Remove and store the transport grip handles (Fig. 8)

once the TreadClimber base is safely on the floor. The

transport grip handles can be reattached for future

transport.

Fig.8

9. Mount the neck mast (Fig. 9) to the base by lightly

torquing four socket head cap screws in place at the

front of the base frame.

Hardware:

o5/16-18 X .75” Socket Head Cap Screw (Location – A)

o5/16-18 X 1.0” Socket Head Cap Screw (Location – B)

QTY: 2 Each

o5/16 Split Lock Washer

o5/16 Flat Washer

QTY: 4 Each

Final Torque:

240 In-Lbs (27 Nm)

Fig. 9

Assembly & Setup

STAR TRAC FITNESS 6 of 14 635-4175 Rev: B

10. Connect the cables extruding through the lower section

of the neck mask into the corresponding locations on

the lower base (Fig. 10).

Fig. 10

ASSEMBLY TIP

For ease of component alignment; installation of the handrail & console frame components requires that the

corresponding securing screws are initially loosely threaded until instructed to apply final torque to each piece of

hardware in step 17 of the assembly process.

11. Mount the left & right lower handrail sections to the

TreadClimber base and loosely thread four socket head

cap bolts to each handrail mount (Fig. 11) along with

sliding on the corresponding left & right handrail

grommets into place.

Hardware:

o5/16-18 X 1.0” Socket Head Cap Screw

o5/16 Flat Washer

o5/16 Split Lock Washer

QTY: 4 Each

Final Torque:

240 In-Lbs (27 Nm)

Fig. 11

12. Slide a beauty ring onto each lower handrail section

(Fig. 12) and mount the upper handrail by loosely

threading two button head cap screws in place. Verify

that the radius cutout clears the lower securing screw.

Hardware:

o1/4-28 X 3/8” Button Head Cap Screw

QTY: 2 Each

Final Torque:

35 In-Lbs (4.0 Nm)

Fig. 12

Assembly & Setup

STAR TRAC FITNESS 7 of 14 635-4175 Rev: B

13. Slide on the second set of beauty rings (Fig. 13) onto

each upper handrail while making sure the radius

cutouts clear the available threaded holes.

Fig. 13

14. Slide the console frame onto each upper handrail

(Fig. 14) and rest the center of the console frame on

top of the neck mast plate.

Fig. 14

15. Loosely thread four socket head cap screws (Fig. 15)

with washers through the neck mast mount plate on to

the console frame mount plate.

Hardware:

o5/16-18 X 1.0” Socket Head Cap Screw

o5/16 Flat Washer

o5/16 Split Lock Washer

QTY: 4 Each

Final Torque:

240 In-Lbs (27 Nm)

Fig. 15

Assembly & Setup

STAR TRAC FITNESS 8 of 14 635-4175 Rev: B

16. Secure the console frame to the handrails (Fig. 16) by

loosely threading two button head cap screws through

the rail into the console frame.

Hardware:

o1/4-28 X 3/8” Button Head Cap Screw

QTY: 2 Each

Final Torque:

35 In-Lbs (4.0 Nm)

Fig. 16

17. Using a torque wrench, go back to steps: 9, 11, 12, 15,

& 16 to thread all bolts mentioned in each step to their

corresponding final torque (Fig. 17) specifications

which are listed in the notes section of the step

instructions.

Fig. 17

18. Hover the top half of the display (Fig. 18) over the

console frame.

Fig. 18

Assembly & Setup

STAR TRAC FITNESS 9 of 14 635-4175 Rev: B

19. Mate all the applicable electrical connections coming

from the neck (Fig. 19) to the back of display electronics

board (Fig. 20).

Fig. 19

NOTE

Audio and coaxial connections are only used if a

personal television is mounted to the machine.

Otherwise these cables remain unused.

Fig. 20

20. Slide the left & right display alignment studs (Fig. 21)

into the corresponding console frame guide holes to

rest the top half of the display on to the console frame.

WARNING

Verify that during mounting of the console; the alignment studs do

not interfere or damage the cable harness that runs through the

tube. Any cable interference will prevent the console from settling

correctly on the console frame.

Fig. 21

21. From the back of the display (Fig. 22) secure the

display’s grounding wire to the frame using a washer &

phillips head screw.

Hardware:

o#8-18X 3/4” Phillips Pan Head Thread Tap Screw

oM4 Flat Washer

QTY: 1 Each

Fig. 22

Assembly & Setup

STAR TRAC FITNESS 10 of 14 635-4175 Rev: B

22. Secure the display to the console frame by installing

five phillips head screws with washers at the

corresponding circled locations (Fig. 23).

Hardware:

o#8-18X 3/4” Phillips Pan Head Thread Tap Screw

oM4 Flat Washer

QTY: 5 Each

Fig. 23

23. Mate the back shroud of the display with the rest of the

assembly by installing eight phillips head screws at the

corresponding circled locations (Fig. 24).

Hardware:

o#8-18X 3/4” Phillips Pan Head Thread Tap Screw

QTY: 8 Each

Fig. 24

24. Dislodge the rear step shroud from the TreadClimber

base (Fig. 25) and move the handrail grommets up the

handrails.

Fig. 25

Altri manuali per TreadClimber

Indice

Altri manuali Star Trac Macchina passo-passo

Star Trac

Star Trac 8 SERIES Manuale utente

Star Trac

Star Trac E-ST Manuale utente

Star Trac

Star Trac Fitness E-ST 5090 Manuale utente

Star Trac

Star Trac E-TC Istruzioni operative

Star Trac

Star Trac SC4100 Manuale utente

Star Trac

Star Trac Fitness E-ST 5090 Manuale utente

Star Trac

Star Trac Pro Stepper Manuale utente

Manuali Macchina passo-passo popolari di altre marche

Domyos

Domyos ST 230 Manuale utente

Spirit

Spirit CRS800 Manuale utente

WAVE EXCITE

WAVE EXCITE CLASS & TREND Manuale utente

Spirit

Spirit CS800 Manuale utente

NordicTrack

NordicTrack Mtn740 Stepper Manuale utente

Pro-Form

Pro-Form 3001 Stx Stepper Manuale utente

AsVIVA

AsVIVA ST4 Manuale utente

Cricket

Cricket CST17 Manuale utente

STAR TRAC FITNESS

STAR TRAC FITNESS P-ST Stepper Manuale utente

Spirit

Spirit XS895 Manuale utente

Sunny Health & Fitness

Sunny Health & Fitness P8000 Manuale utente

Weslo

Weslo Ascent 730 Manuale utente

Image

Image 877 Manuale utente

Impex

Impex Hers MS-94 Manuale utente

Argos

Argos Opti Mini Stepper Manuale del proprietario

Karman

Karman MoonRocker Manuale utente

Sunny

Sunny 012 Manuale utente

Weslo

Weslo WLEL31216.0 Manuale utente