Starck NETATMO Manuale utente
You can watch this installation at:
http://netatmo.com/video2
You can watch this installation at:
http://netatmo.com/video3
Replacing a wireless thermostat
or installing your first thermostat
2
• Read these instructions carefully before starting the installation.
• The Netatmo Thermostat must be installed according to
applicable standards.
• Before any intervention, make sure power is turned off.
• The Netatmo Thermostat cannot control electric converters.
Warning!
In the box
Color Adhesives (Power Plug)*
Thermostat Relay Boiler adapter
Mobile stand
* not used or optional in this setup
(Mounting Plate)*
+
(Trim plate)*
3 AAA batteries 4 screws
4 screw anchors
Tape
Wiring
Open the boiler door (use the
boiler manual, if necessary).
Identify the thermostat terminals in
the boiler, often labeled LS-LR, TA or
COM-NO. They may be identifiable
thanks to a shunt between the two
thermostat terminals.
If your are replacing a wireless ther-
mostat, find your former thermostat’s
relay and remove it.
If you are installing your first thermos-
tat, please remove the shunt between
the two thermostat terminals.
Connect the black and grey wires
of the boiler adapter cable to the
thermostat terminals.
Thermostat terminals
Black and grey wires
No polarity
LS/ LR
TA
COM / NO
or
or
Note : Some thermostats are connected to dierent terminals from those on the diagram’s list (for
example, eBus, EMS…). In this case, you will have to identify the right thermostat terminals to connect the
Relay of the Netatmo Thermostat.
Wiring
Connect the blue and brown
wires of the boiler adapter
cable to the power supply
terminals (P/N or L/N).
Our forum can help you
identify where to plug the wires
in, at forum.netatmo.com.
In doubt, please send a picture
of your wiring to:
and our support team will help
you identify the right terminals.
Thermostat terminals
Black and grey wires
No polarity
230 V Power supply terminals
Blue and brown wires
P / N
L / N
or
The boiler adapter should be placed
as far as possible from metallic items
(wiring, pipes, electrical grid…).
The boiler adapter can be axed to the wall with the double-sided tape
or the screws provided.
30 cm
Setting the Relay
or
Connect the Relay into the boiler
adapter.
Switch the power supply back
on.
The Relay will blink white.
Note : If the Relay does not blink after turning the power back on, it is not power supplied.
Please check how the blue and brown wires are wired. Do not forget to switch o the power supply
before any intervention.
Testing the Relay
1
2
3
Push the Relay button. The Relay will light up white
and switch on the boiler.
Push the Relay
button again. The Relay light will turn o to
indicate the boiler is o.
Note: If the boiler doesn’t switch on when the white light is on, the Relay can be incorrectly wired to the
boiler. In this case, check where the grey and black wires are connected. Please note that some boilers
can take up to 20 minutes to respond after pushing the Relay’s button.
In doubt, please read in your boiler’s instructions manual [ the «room thermostat» section].
Testing the Relay
4
12
3
Insert the batteries into
the Thermostat.
The Thermostat will display the
start screen and search for the Relay.
Thermostat
If the Thermostat has found the
Relay, it will display the setpoint and
the room temperatures.
If the Thermostat hasn’t found the
Relay, it will display the «!» symbol.
In this case, move the Relay closer to
the Thermostat and wait until the «!»
symbol disappears.
20
215
0
+
Measured temperature
Desired temperature
or 20
215
0
+
12
Customization
You can choose to customize
your Thermostat by using one
of the colour adhesives.
Take o the outer frame of the adhesive.
Stick it on the back of your Thermostat.
2
3
1
Altri manuali per NETATMO
3
Indice
Altri manuali Starck Termostato
