starlight FPE-2411SS Manuale utente
1
Star-Light Food Processor....................................................EN
INSTRUCTION MANUAL
Food Processor
FPE-2411SS
220-240V~50/60Hz
820-1100Watts
FOR HOUSEHOLD USE ONLY
2
Read this user manual carefully before you use the appliance and save it for
future reference.
Danger
- Never immerse the motor unit in water or any other liquid, nor rinse it under
the tap.
Warning
- Check if the voltage indicated on the appliance corresponds to the local mains
voltage before you connect the appliance.
- Never connect this appliance to a timer switch in order to avoid a hazardous
situation.
- Do not use the appliance if the mains cord, the plug or other parts are damaged.
- If the mains cord is damaged, you must have it replaced by supplier, a service
center authorized by Supplier or similarly qualified persons in order to avoid a
hazard.
- This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning
use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the
appliance. - Never let the appliance run unattended.
- Never use your fingers or an object (e.g. a spatula) to push ingredients down the
feeding tube while the appliance is running. Only use the pusher for this purpose.
- Be very careful when you handle the discs, blender blade unit or food processor
blade unit. Be especially careful when you remove them from the food processor
bowl or blender jar, when you empty the bowl or jar and when you clean them.
Their cutting edges are very sharp.
Caution
- Never switch off the appliance by turning the blender jar, the food processor
bowl or the juicer bowl. Always switch off the appliance by turning the speed
control knob to OFF.
- Switch off the appliance before you detach any accessory.
- Unplug the appliance immediately after use.
- Always unplug the appliance before you reach into the blender jar with your
fingers or an object (e.g. a spatula).
- Wait until moving parts stop running before you remove the lid of the bowls or
jar. - Never use any accessories or parts from other manufacturers or that
Supplier does not specifically recommend. If you use such accessories or parts,
your guarantee becomes invalid.
- Do not exceed the maximum content indicated on the food processor bowl or
the blender jar.
- Do not use the juicer if the sieve is damaged.
- Consult the tables in this user manual for the correct quantities and processing
times.
3
- Thoroughly clean the parts that come into contact with food before you use the
appliance for the first time.
- Let hot ingredients cool down before you process them (max. temperature
80°C/175°F).
Built-in safety lock
This feature ensures that you can only switch on the appliance if you have
assembled the blender jar with blade unit, the food processor bowl, the juicer
bowl with coupling unit or the citrus press correctly on the motor unit. If the
blender jar with blade unit, the food processor bowl, the juicer bowl with coupling
unit or the citrus press is assembled correctly, i.e. when it has been turned in the
direction of the ‘locked’ symbol as far as possible (‘click’), the built-in safety lock
will be unlocked.
Assembly/disassembly
Blade - tips and warnings
Do not let the appliance run too long when you chop (hard) cheese or chocolate.
Otherwise these ingredients become too hot, start to melt and turn lumpy. Always
put the food processor blade unit in the food processor bowl before you add the
ingredients. Do not use the food processor blade to chop very hard ingredients
such as coffee beans, nutmeg, turmeric and ice cubes, as this may cause the
blade unit to become blunt.
Do not fill the bowl beyond the MAX indication.
-The standard processing time for all chopping jobs is max. 30 seconds each
time.
-If you chop onions, press the pulse button a few times to prevent the onions
4
from becoming too finely chopped.
If food sticks to the blade unit or to the inside of the food processor bowl:
1 Switch off the appliance.
2 Remove the lid from the food processor bowl.
3 Remove the ingredients from the blade unit or from the wall of the bowl with a
spatula.
Kneading accessory - tips and warnings
-Always put the kneading accessory in the food processor bowl before you
add the ingredients.
-The standard processing time for all kneading jobs is max 30 Seconds each
time.
5
Discs - tips and warnings
Do not exert too much pressure on the pusher when you press ingredients down
the feeding tube.
Do not let the appliance run too long when you shred (hard) cheese. Otherwise
the cheese becomes too hot, starts to melt and turns lumpy.
Do not use the shredding disc to shred chocolate. Only use the food processor
blade unit for this purpose.
Do not fill the bowl beyond the MAX indication.
1 Pre-cut large ingredients to make them fit into the feeding tube.
2Fill the feeding tube evenly for the best results.
- When you shred or granulate soft ingredients, use a low speed to prevent the
ingredients from turning into a puree.
- If the ingredients you are going to shred or slice have a small diameter, put the
outer pusher in the feeding tube to make the feeding tube smaller. Then use the
inner pusher to push the ingredients down the feeding tube.
- When you have to process a large amount of ingredients, process small
batches and empty the bowl between batches.
Balloon beater - tips and warnings
You can use the balloon beater to whip cream, to whisk eggs and egg whites and
to make instant pudding, mayonnaise and sponge cake mixture. Do not use the
balloon beater to prepare cake mixtures with butter or margarine or to knead
dough. Use the kneading accessory for these jobs.
Do not fill the bowl beyond the MAX indication.
-Make sure the bowl and the balloon beater are dry and free from grease when
you whisk egg whites. The egg whites have to be at room temperature.
-Always clean the balloon beater after use.
6
Citrus press - tips and warnings
Do not fill the bowl beyond the MAX indication. Built-in safety lock: the citrus press
only works when the sieve is assembled properly on the motor unit and the cone is
assembled properly in the sieve. All parts have been assembled properly, the cone
starts rotating as soon as you turn the switch to the minimum speed setting.
1 Set the control knob to the minimum speed setting.
2Press the citrus fruit onto the cone.
Note: Stop pressing from time to time to remove the pulp from the sieve. When you
have finished pressing or when you want to remove the pulp, switch off the
appliance and remove the bowl from the appliance with the sieve and cone on it.
7
Juicer - tips and warnings
Never insert your hand or another object (e.g. a fork, knife, spoon or spatula) into
the feeding tube. Only use the pusher supplied with the appliance for this purpose.
Wait until the sieve has completely stopped rotating before you remove the lid.
-Always check the sieve before use. Do not use the juicer if you notice any
damage like cracks, crazes or a loose grating disc.
-The standard processing time for all juicing jobs is 30-120 seconds.
-Peel citrus fruits, pineapples, melons, etc. before you juice them.
-Stone cherries, plums, apricots, peaches, etc. before you juice them.
Blender - tips and warnings
Always assemble the sealing ring onto the blender blade unit before you attach the
blade unit to the blender jar.
Always let the appliance cool down to room temperature after you have processed
two batches.
Never open the lid when the blade rotates.
◆Built-in safety lock: you can only switch on the appliance when the blender jar
has been assembled in such a way that the ridge on the blade unit is aligned with
the ‘locked’ symbol on the motor unit.
-To add liquid ingredients during processing, remove the measuring cup and
pour them into the blender jar through the hole in the lid.
-Pre-cut solid ingredients into smaller pieces before you process them.
-If you want to prepare a large quantity, process small batches of ingredients
instead of a large quantity at once.
8
- Use cooked ingredients when you blend a soup.
- When you process a liquid that is hot or tends to foam (e.g. milk), do not put
more than 1 liter in the blender jar to avoid spillage.
- If you are not satisfied with the result, switch off the appliance and stir the
ingredients with a spatula. Remove some of the contents to process a smaller
quantity or add some liquid.
If ingredients stick to the wall of the blender jar:
1 Switch off the appliance and unplug it.
2 Remove the lid and use a spatula to remove the ingredients from the wall of
the jar.
3 Keep the spatula at a safe distance of approx. 2cm from the blades.
Grinder Mill
1. Remove the Grinder jar lid from the Grinder Jar.
2. Fill with food (do not fill more than half full), then screw in the Blender Base
unit till it is tightened and secure.
3. Place the Grinder Mill onto the Motor Base and follow the instructions on page
6 to lock in the Grinder Mill.
NOTE:
- After milling, you can replace the blade unit with the sprinkler lid and shake out
your food.
- Switch to maximum speed or use pulse.
Indice
Lingue:
