Stealth 35STS12 Manuale utente

Doc-rev 20240115

SAVE THESE INSTRUCTIONS. This manual contains important safety precautions which should be read and understood before operating the product. Failure to do so could result in

serious injury. Speciﬁcations, descriptions and images in this manual are as accurate as known at the time of publication, but are subject to change without notice.

ENGLISH

WINCH MODELS

WINCH

OWNERS MANUAL

STS, STA,

STS, STA

ENGLISH

DEUTSCH

FRANÇAIS

POLSKI

ESPAÑOL

ITALIANO

WINCH MANUAL INTRODUCTION



INTRODUCTION

Congratulations on your purchase of a winch. We design and build

winches to strict speciﬁcations and with proper use and maintenance your

winch should bring you years of satisfying service.

Every eort has been made to ensure the accuracy and completeness of

the information in this manual at the time of publication, and we reserve

the right to change, alter and/or improve the product and this document

at any time without prior notice.

SAFETY DEFINITIONS

Your winch can develop tremendous pulling forces and if used unsafely

or improperly could result in property damage, serious injury or death.

Throughout this manual, you will ﬁnd the following symbols for caution,

warning and danger. Pay particular attention to the notes preceded

by these symbols as they are written for your safety. Ultimately, safe

operation of this device rests with you, the operator.

DANGER

DANGER indicates a hazardous situation which,if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

NOTICE

NOTICE indicates information considered important, but not hazard-

related (e.g., messages relating to property damage).

GETTING TO KNOW YOUR WINCH

Your winch is a powerful piece of machinery. It is important that you

understand the basics of its operation and speciﬁcations so that

when you need to use it, you can use it with conﬁdence and safety.

Below is a list of the components of your winch and their uses.

1. This winch is engineered for maximum line pull with only one layer of

cable spooled onto the winch drum (the ﬁrst layer).

2. Motor: The motor is powered by a 12/24-volt battery and provides

power to the gear assembly which turns the drum and winds the wire

rope in a direction.

3. Winch Drum: The winch drum is the cylinder on which the wire rope is

stored. It can be spooled In or Out by use of the remote lead switch.

4. Winch Rope: Your winch been supplied with galvanized aircraft

steel cable or synthetic rope and is designed speciﬁcally for load

capacity of the rated line pull of this winch. The cable feeds on from

underneath the drum position, it is looped at one end to accept the

hook.

5. Fairlead (Supplied with selective models): For when using the winch

at an angle the roller fairlead acts to guide the rope onto the drum

evenly and minimizes damage to the rope or winch from abrasion.

6. Gear Assembly System: The reduction gears convert the winch

motor power into extreme pulling forces.

7. Braking System: Braking action is automatically applied to the winch

when the winch motor is stopped or there is a load on the wire rope.

This is achieved by a separate external mechanical brake which

applies the braking action. (Brakes are NOT designed as securing

devices and the winch cables should never be left attached when

vehicle / equipment is in transport).

8. Free Spooling Clutch: The clutch allows the operator to manually

disengage (“CLUTCH OUT”) the spooling drum from the gear train.

This is called free spool. Engaging the clutch (“CLUTCH IN”) locks

the winch into the gear system.

9. Solenoid: Power from the vehicle battery ﬂows through the

weatherproof switch before being directed to the winch motor.

10. Wired Remote lead Switch: The remote switch leads have a dual

switch for powering in or powering out your winch drum. The remote

control allows you to stand clear of the wire rope when the winch is

under load.

11. Wireless remote (Supplied on selective models): This is designed

and oered for ‘Oroad’ or ‘None Commercial’ use only and is not

included in any warranty oered, This allows the operator to always

control the winch from up to 50 Ft away.

12. Universal Flat Bed Mounting Channel: (Optional) Your winch could

have been optionally supplied with a ﬂat bed mounting channel that

can be mounted to most ﬂat surfaces such as trailers, truck beds

and structures etc. The mounting channel also has a number of

mounting holes and holes to accept your roller fairlead.

13. Pulley/Snatch Block: (Optional) If your winch is supplied with a

pulley/snatch block which can double the pulling power of the winch,

or change the pulling direction without damaging the wire rope. We

recommend you to use a double line and snatch block for pulling over

70% of the rated line pull.

WINCH MANUAL INTRODUCTION



IMPORTANT SAFETY INSTRUCTIONS

DANGER

DO NOT EXCEED RATED CAPACITY.

INTERMITTENT USE ONLY  COOL BETWEEN USES.

DO NOT use winch for lifting/moving people or live animals.

A minimum of ﬁve wraps of cable around the drum barrel is necessary

for pulling and holding the rated load. The cable clamp is not designed

to hold the load without the 5 wraps of cable around the drum.

(usually marked red on the drum end of the cable)

DANGER

Keep yourself and others a SAFE DISTANCE to the side of the cable

when under tension.

NEVER stand or step over a cable, or near a cable under load using a

winch blanket or sail is strongly recommended.

DON’T move the vehicle to pull a load (towing) on the winch cable.

This could result in cable breakage.

Disconnect the remote control and isolate when not in use.

DANGER

DO NOT exceed maximum pull rating. Avoid “shock loading” by using

the remote lead switch intermittently to take up the slack in the wire

rope. “Shock loading” can far exceed the rated capacity for the wire

rope and drum and will result in damaging winch and brake. By doing

so will void any warranty.

DANGER

DO NOT use you winch as securing device it is not designed for this

and will result in damaging winch and brake and will void any warranty.

DO NOT exceed maximum line pull ratings shown on the tables.

DO NOT use as a hoist. Do not use for overhead lifting.

DANGER

NEVER cut, weld, or modify any part of the winch or cable. By doing

so will void any warranty

DANGER

When re-spooling the cable Ensure that the cable spools in the

under-wind position with the cable entering the drum from the

bottom, not the top. To re-spool correctly, and while wearing gloves,

keep a slight tension on the cable while pushing the remote control

button to draw in the cable. Walk toward the winch NEVER allowing

the winch cable to slide through your ﬁngers or hands.

DO NOT let your hands get within 12”(30cm) of the winch while re-

spooling. Turn o the winch and repeat the procedure until a few feet

of cable is left. Disconnect the remote control and ﬁnish spooling by

hand by rotating the drum manually with the clutch disengaged. Keep

hands clear of the fairlead and drum while the winch is under power.

DANGER

Failure to read and understand these warnings may result in personal

injury and/or property damage.

Always use gloves to protect hands when handling any type or cable/

rope. Never let the cable slide through your hands.

NEVER connect the cable back to itself.

Always apply blocks/chocks/straps to the wheels of the vehicle/

equipment when on an incline and in transportation.

No modiﬁcations, alterations, or deviation to the winch are authorized

by the manufacturer and MUST NOT be made. By doing so will void

any warranty.

Duration of winching pulls should be kept as short as possible. If

the motor becomes uncomfortably hot to the touch, stop winching

immediately and let it cool down for approx 8 mins minutes. Do not

winch for more than two minutes at or near the maximum rated load

without resting for 8 minutes.

DANGER

If the motor stalls DO NOT maintain winching. Winches are designed

and made for intermittent use and should be used in conjunction with

their duty cycles.

NEVER release the free-spool clutch when there is a load on the

winch as the load will roll backwards.

Use hand saver hook when handling the hook for spooling or un-

spooling the wire rope.

NOTICE

The winch and its all-derivative types are rated at rated capacity when

spooling the ﬁrst rope layer on the drum. Overloading can damage

the winch / motor / or wire rope.

For loads over 70% of rated line pull, we recommend the use of the

pulley block / snatch block to double the wire rope line and reduce the

strain. This will aid in two ways:

It will reduce the number of rope layers on the drum and reduce the

load on the wire rope by as much as 50%. When doubling the lineback

to the vehicle, always attach to the frame or another load bearing

point..

WINCH MANUAL INTRODUCTION



NOTICE

The vehicle engine should always be kept running during winching

operation to minimize battery drain and maximize power and speed

of the winch. If the winch is used for a considerable amount of time

with the engine switched o the battery will drain and be too weak to

restart the vehicle engine. If this happens stop winching immediately,

jump start the vehicle and charge the battery up before resuming

winching operation.

NOTICE

Get to know your winch before you need to use it. We recommend

that you set up a few test runs to familiarize yourself with rigging

techniques; the sounds your winch makes under various loads and the

way the cable spools on the drum, etc.

INSPECT the wire rope and equipment before each use. A

frayed or damaged rope must be replaced immediately. Use

only manufacturer’s identical replacement rope with the exact

speciﬁcations. (Ropes are not covered by any warranty oered)

INSPECT the winch installation and bolts to ensure that all bolts are

tight before each operation or periodcally.

NOTICE

Store the remote control lead inside your vehicle or in a safe place.

Never connect the winch cable back to itself. This will cause cable to

damage. Always use a pulley, snatch block, sling or chain of suitable

strength as shown in the illustrations.

NOTICE

Any winch that appears to be faulty, damaged, worn, or operates

abnormally MUST BE REMOVED FROM SERVICE UNTIL REPAIRED,

REPLACED OR OVERHAULED. It is recommended that the necessary

repairs ARE made by a manufacturer’s authorized repair facility ONLY.

NOTICE

Pull only on areas of the vehicle as speciﬁed by the vehicle

manufacturer.

– Only accessories, attachments and/or adapters supplied by the

manufacturer shall be used.

CAUTION

When using the tool, basic safety precautions should always be

followed to reduce the risk of personal injury and damage to the

equipment. Read all these instructions before using this tool!

WARNING

Keep children away. Children must never be allowed in the work area,

Do not let them handle machines, tools, extension cords or operate

this tool.

WARNING

Store idle equipment. When not in use, tools must be stored in a dry

location to inhibit rust. Always lock up tools and keep out of reach of

children.

CAUTION

Dress properly. Do not wear loose clothing or jewelry as they can

be caught in moving parts. Protective, electrically non-conductive

clothes and non-skid footwear are recommended when working.

Wear restrictive hair covering to contain long hair.

WARNING

Use eye and ear protection. Always wear impact safety goggles. Wear

a full-face shield if you are producing metal ﬁlings or wood chips.

Wear a dust mask or respirator when working around metal, wood,

and chemical dusts, and mists.

CAUTION

Maintain this winch with care. Keep this tool dry and clean for

better and safer performance. Follow instructions for lubricating

and changing accessories. Inspect winch rope periodically and,

if damaged, have them replaced immediately by an authorized

technician. The handles must be kept clean, dry, and free from oil and

grease always.

Disconnect or unplug remote switch when not in use.

DANGER

Stay alert, watch what you are doing, use common sense. Do not

operate any tool when you are tired.

WARNING

Check for damaged parts. Before using this winch, any parts that

appear worn or damaged should be carefully checked to determine

that it will operate properly and perform to its intended function.

Check for damage including alignments, binding of moving parts;

mounting ﬁxtures. Any part that is damaged should be properly

repaired or replaced by a qualiﬁed person. Do not use the tool if any

switch does not turn “On” and “O” properly.

WARNING

Replacement parts and accessories. When repairing or servicing,

only use identical replacement parts. The use of any other parts will

void the warranty.

WINCH MANUAL INTRODUCTION



WARNING

Do not operate tool if under the inﬂuence of alcohol or drugs.

Read warning labels on prescription to determine if your judgment or

reﬂexes are impaired while taking drugs. If there is any doubt, do not

operate the tool.

DANGER

Keep hands and body away from Fairlead (cable intake slot) when

operating.

Always secure vehicle in position before using winch.

WARNING

Be certain the winch is properly bolted to a structure (or vehicle) that

can hold the winches maximum rated load.

Do not use inappropriate attachments to extend the length of the

winch cable.

DANGER

Never lift people or hoist loads over people or lift live animals.

Never come in between the winch and the load when operating.

WARNING

Do not apply any loads to the winch when cable is fully extended

past the safety mark. Keep at least 5 full wraps of cable on the spool,

(Usually marked red on the winch cable at the drum end.)

After moving any piece of equipment with the winch, secure the the

equipment in place. Do not rely on the winch to hold for an extended

period of time nor whilst in transport, winches are not securing

device, By doing so will void any warranty

CAUTION

Examine winch before using. Components may be aected by

exposure to chemicals, salts, and rust.

Do not cross over or go underneath winch cable when under load.

Use gloves while handling cable.

WARNING

Never operate winch if cable shows any signs of weakening, such as

knotting or kinking. If it does you must replace immediately.

DANGER

Do not move your vehicle with the cable extended and attached to the

load. You could easily exceed the winch rating and snap the cable.

When the vehicle is parked on an incline you should use wheel chocks.

CAUTION

Always re-spool cable neatly after any operation this will avoid any

winch cable misalignment for the next use

CAUTION

The winch cable must be wound onto the drum under a load of at least

10% of the rated line pull or the outer wraps will draw into inner wraps

and damage winch cable.

Before operating the winch under load you should check proper

function of the winch by engaging and disengaging the clutch, by

operating the directional controls, and operating the speed controls.

This will ensure that the winch is working properly and will help

prevent unintended damage and injury. Cycling the winch prior to

loading will also ensure the gears are properly aligned.

CAUTION

Batteries contain gases which are ﬂammable and explosive. Wear eye

protection during installation and remove all jewelry. Do not lean over

battery while making connections.

WARNING

It is strongly recommended a battery isolator is installed to protect

vehicle, equipment and user from hazardous situations, if one isn’t

supplied it is recommended one is purchased and installed before

operation of the winch.

Failure to install a battery isolator or safety cut o could result in

damage to the vehicle, equipment and(or) operator and will result in

voiding any warranty oered.

WINCH MANUAL RIGGING TECHNIQUES



WINCH ASSEMBLY AND MOUNTING

Red Battery +

Black Battery -

Remote Control

1. Your winch is designed with a bolt pattern that is standard in

this class of winch. Many winch mounting kits are available that

utilize this bolt pattern for the most popular vehicle and mounting

channels. If you cannot ﬁnd a kit locally, contact us and we will

provide you with the name of a dealer near you. If you utilize the

mounting channel, you must ensure that it is mounted on a ﬂat

surface so that the three major sections (motor, drum and gear

housing) are properly aligned. Proper alignment of the winch will

allow even distribution of the full rated load and reduce the chance

of damaging winch or equipment. Poor installation contributes to

approx 90% equipment or winch damage.

2. Start by connecting the Roller Fairlead to the Mounting Channel

using the 2 screw cap assemblies (Make sure the bolt is placed

through the mounting channel and roller fairlead from inside the

channel. This will allow enough clearance for the winch to be placed

in the channel without obstruction.)

3. Assemble the winch to the (optional) Mounting Channel by ﬁrst

pulling and releasing the clutch knob to “Out” position (Free

Spooling). Pull out a few inches of cable from the drum and feed the

wire loop through the opening in the front of the mounting channel

and roller fairlead. Now, using the remaining screw cap assemblies

secure the winch to the mounting channel.

4. First connect up the short red and black leads to the motor terminals

and then connect the long battery leads to a battery as per the

assembly drawing. Remember every type of winch is dierent.

CAUTION

Batteries contain gases which are ﬂammable and explosive. Wear eye

protection during installation and remove all jewelry. Do not lean over

battery while making connections.

5. Assemble the Clevis Hook to the cable. Take o the pin from the

Clevis Hook, connect the Clevis Hook to the cable and mount the pin

back to the Clevis Hook.

6. Always use the Hand Saver (Optional) when free-spooling and re-

spooling the wire rope. Using the Hand Saver keeps your hands and

ﬁngers away from the rotating drum.

7. Check for proper drum rotation. Pull or turn the clutch knob to the

“OUT” “Disengage” position (Free-spooling). Pull out some cable

from the drum, and then turn the clutch knob to the “IN” “Engage”

position to engage the gears. Press the cable out button on the

remote lead switch. If the drum is turning and releasing cable, then

your connections are accurate. If the drum is turning and collecting

more cable, then reverse the leads on the motor. Repeat and check

rotation.

NOTICE

For D style winch (without solenoid) the winch operation is controlled

directly through the motor and not through the control box assembly.

RIGGING TECHNIQUES

Locate a suitable anchor such as a strong tree trunk or boulder.

ALWAYS use a sling or strap as an anchor point on a object, Never use the

cable or hook as a anchor point attached to an object.

CAUTION

NEVER attach the clevis hook back onto the cable as this could cause

damage to the cable.





CAUTION

Do not winch from an acute angle as the wire rope will bind up on

one side of the drum causing damage to wire rope (Bird Nesting) and

cause major damage to winch and possible equipment.

WINCH MANUAL WINCHING TECHNIQUES AZ





NOTICE

Short pulls from an angle can be used to straighten the vehicle/

equipment. Long pulls should be done with the wire rope in a

straight line to winch/vehicle, see above illustration

CAUTION

When pulling a heavy load, place a blanket or jacket over the wire rope

ﬁve or six feet from the hook because in the event of a broken cable it

will dampen the force.

For additional protection open the hood/bonnet of the vehicle as

shown.

NOTICE

For pulls over 70% rated line pull, we recommend the use of the snatch

block/pulley block to double line the wire rope. This reduces the load on

the winch and the strain on the rope.

Single Line Double Line

DANGER

Never use your winch for overhead hoisting, lifting of people, moving

people or moving of live animals.

WINCHING TECHNIQUES AZ

a. Take time to asses your situation and plan your pull.

b. Put on gloves to protect your hands.

c. Disengage the clutch where possible to allow free-spooling and also

save battery power.

d. (If supplied) Attach the hand saver hook to the clevis hook.

e. Pull out the wire rope to your desired anchor point safely.

f. Secure the clevis hook to the anchor point: Sling, chain or snatch block.

Do not attach the hook back onto the wire rope.

g. Engage the clutch.

h. Connect the remote control lead to the winch.

i. Start your engine to ensure power is being replenished to the vehicle

battery.

j. Power in the wire rope guiding the wire under tension to draw up the

slack in the wire. Once the wire is under tension stand well clear. Never

stand or step over the wire rope under tension.

k. Double check your anchors and make sure all connections are secure.

l. Inspect the wire rope. Make sure there are at least 5 wraps of wire rope

around the winch drum.(usually marked with red)

m. Drape a blanket or sail (Sold separately) over the wire rope

approximately 5 to 6 feet from the hook. Open the hood/bonnet for

added protection.

n. Clear the area. Make sure all people, spectators are well back and that

no one is directly in front or behind the vehicle or anchor point.

o. Begin winching. Be sure that the wire rope is winding evenly and tightly

around the drum. If needed, the vehicle that is being winched can be

slowly driven to add assistance to the winching process. Avoid shock

loading; keep the wire rope under tension.

p. The vehicle to be winched should be placed in neutral and the

emergency brake released. Only release the brake pedal when under full

tension. Avoid shock loading to the winch. This can damage the winch,

rope and vehicle.

q. The winch is meant for intermittent use. Under full load with a single

line rig do not power in for more than 8 minutes without letting the motor

cool down for a few minutes and then resume the winching operation.

r. The winching operation is complete once the vehicle is on stable ground

and or can drive under its own power.

s. Secure the vehicle. Be sure to set the brakes and place the vehicle in

park.

WINCH MANUAL MAINTENANCE



t. Release the tension on the wire rope. The winch is NOT designed

as securing device and should NEVER hold a load or secure whilst in

transport, winch cable MUST be released when equipment or vehicle is

secure. Not doing so will possibly damage the brake and winch and void

any warranty.

u. Disconnect the wire rope from the anchor and NEVER leave connected.

v. Rewind the wire rope. Make sure that any wire already on the drum has

spooled tightly and neatly. If not, draw out the wire and re-spool from the

point where the rope is tight.

w. Keep your hands clear of the winch drum and fairlead as the wire rope is

being drawn in.

x. Secure the hook and hook strap.

y. Disconnect the remote control lead and store in a clean, dry place.

z. Clean and inspect connections and mounting hardware for next

winching operation.

MAINTENANCE

1. Periodically check the tightness of mounting bolts and electrical

connections. Remove all dirt or corrosion and always keep clean.

2. Do not attempt to disassemble the gear box. Repairs should be

done by the manufacturer or an authorized repair center.

3. The gear box has been lubricated using a high temperature lithium

grease and is sealed at the factory. No internal lubrication is

required.

REPLACING THE WIRE ROPE

If the wire rope has become worn or is beginning to show signs of fraying,

it must be replaced before being used again.

1. Turn the clutch to the “CLUTCH OUT” position.

2. Extend cable to its full length. Note how the existing cable is

connected to the drum.

3. Remove old cable assembly and attach new one as the old cable

connected to the drum. Insert the end of the new rope and secure

the allen screw.

4. Ensure that the new cable wraps in the same rotation direction as

the old one. The cable should exit the drum from the bottom, under

the drum. (Underwind).

5. Turn the clutch to the “CLUTCH IN” position.

6. Winch cable onto drum, ﬁrst ﬁve wraps being careful not to allow

kinking, then winch cable must be wound onto the drum under a load

of at least 10% rated line pull.

WARNING

Only replace the wire rope with the identical replacement part

recommended by the manufacturer. Steel or synthetic ropes are NOT

covered by any warranty oer and are sole responsibility of the owner

or user to maintain and replace if necessary.

WINCH MANUAL TROUBLESHOOTING



Problem Cause Solution

Motor does not turn on

Remote assembly not connected properly Check remote lead and connections.

Loose battery cable connections Check battery and connections.

Defective remote assembly Replace remote lead assembly.

Defective motor Check for voltage at armature port with Switch

pressed. If no voltage is present, replace motor.

Water has entered motor Allow to drain and dry. Run winch until completely

dry.

Motor runs but drum does not turn Clutch not engaged Turn clutch to the “In” position. If problem persists,

ask a technician to check and repair.

Motor runs slowly or without normal power Insucient current or voltage Operate winch while vehicle motor running

Motor overheating Winch running for too long Allow winch to cool down periodically.

Motor runs in one direction only Loose or corroded battery cable or motor cable

connections.

- Clean and tighten.

-Repair or replace switch assembly.

TROUBLESHOOTING

WARRANTY*

BPE Limited are the sole distributors of these WINCHES and

associated brands/equipment.

BPE Limited (“seller” or BPE) warrants to the original retail buyer

only (“Buyer”) that any mechanical component of this genuine winch

(“product(s)”) are free of defects in material and workmanship for one (1)

year from date of purchase.

The electrical components (including the motor, contactor, and switches)

will be free of defects in material and workmanship for a period of one (1)

year from the original purchase provable date of purchase.

Any product BPE Ltd determines to be defective will be repaired or

replaced at our (BPE Ltd) sole discretion without charge to the Buyer upon

Buyer’s compliance with this procedure. Seller or its Authorized Agent

may make reasonable charges for parts and(or) labour for repairs not

covered by this Warranty. Non warrantable returns will be charged at BPE

Ltd standard rates. The warranties set forth herein are exclusive and in

lieu of all other warranties, whether oral or written, express or implied. All

product(s) are be covered by the standard One (1) year warranty.

If in the event your product becomes faulty

within your warranty period

To obtain service or repair under this warranty, the Buyer shall mail, ship

or otherwise deliver to the manufacturers address, at the Buyers expense;

(1) the Product, (2) a written description of the problem, (3) Buyers name,

address and contact number, (4) copy of the original purchase receipt or

BPE Solutions North America can arrange a suitable collection method

(Charges apply).

Warranty Exclusions

The Warranty does not cover the cost of labour or transportation/shipping

charges for the replacement or installation of defective part(s). This

warranty does not apply to defects of the Product caused by; (1) normal

wear and tear, (2) failure to comply with any installation, maintenance or

subjecting the product to loads in excess of the loads written/listed in

the owner’s manual or as detailed upon the Sellers website, (3) alteration

or modiﬁcation by any parties other than the manufacturer, (4) misuse,

abuse, neglect, accidents, Acts of God, terrorism or (5) failure to correctly

use the item according to the owner’s manual (7) other causes beyond the

control of the Seller after delivery of the Product to the Sellers Authorized

Agent.

Other Exclusions

This Warranty does not cover steel cables, synthetic ropes, fairleads,

wireless remotes or any exterior ﬁnishes outside thirty (30) Days from

purchase.

BPE Limited shall not be responsible or liable for any indirect or

consequential damages. These consequential damages may include, but

are not limited to, lost proﬁts or loss of use, down time or damage to other

person(s) equipment.

BPE Limited reserves the right to change the Product design without

notice. BPE Limited reserves the right to replace any part or whole unit

with a newer design of the same function.

WINCH MANUAL SPECIFICATIONS



SPECIFICATIONS

Rated line pull 3500 lbs (1588 kgs)

Gear reduction ratio 170:1

Motor 12V: Input: 2.4kW / 3.2hp; Output: 1.0 kW / 1.3hp

Overall dimensions 348×116×165mm (13.7”×4.6”×6.5”)

Drum size Ø37mm×80mm (Ø1.46”×3.15”)

Cable

Synthetic rope Wire rope

Ø5mm×14m (Ø13/64”×46.0’ Ø5.4mm×12.8m (Ø7/32”×42.0’)

Net Weight Synthetic rope Wire rope

8.5kg (18.7 lbs) 10.5kg (23.1 lbs)

Line Pull, Speed, Amperes, Volts (First layer):

Line Pull Ibs (kgs) Line Speed ft/min (m/min) Current A (12V DC)

010.2(3.1) 20

1000(454) 8.9(2.7) 75

2000(907) 7.5(2.3) 130

3500(1588) 4.6(1.4) 200

Layers, Line Pull and Rope Capacity

Layer Rated line pull lbs (kgs) Total rope on the drum ft (m)

13500(1588) 5.9(1.8)

22789(1265) 13.5(4.1)

3 2319(1052) 22.0(6.7)

41984 (900) 31.2(9.5)

51733 (786) 42.0(12.8)

35STS12 / 35STA12

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Stealth Verricello

Stealth

Stealth 13V2S12 Manuale utente

Manuali Verricello popolari di altre marche

WARRIOR

WARRIOR Trojan 40PUS12 Guida di riferimento rapido

SVERO

SVERO 16 Manuale utente

Warrior Winches

Warrior Winches C10000NH Manuale utente

Badland Winches

Badland Winches 68146 Manuale utente

Bush

Bush II Series Manuale utente

Badland

Badland APEX 5500 Manuale utente

Quadratec

Quadratec Q9000 Synthetic Manuale

C-Max

C-Max VIGO Manuale utente

Comeup

Comeup DV-9 Manuale utente

Orvea

Orvea Italwinch 805 Manuale utente

Prowinch

Prowinch PWJTHF300 Manuale utente

Clas Ohlson

Clas Ohlson LD2000-A Manuale utente

Topex

Topex 97X080 Manuale utente

Eastbound

Eastbound MotoWinch 1707001 Manuale utente

Runva

Runva EWD8000 Guida di riferimento rapido

Ingersoll-Rand

Ingersoll-Rand LIFTSTAR FG 1500/CN Series Guida all'installazione

Granit

Granit 11157675 Manuale utente

TREX

TREX TB75 Manuale utente