Steam The Ripple Maker Manuale utente
2
Table of
Contents
1. Important Safety Warnings and Cautions
1.1. Safety Warnings
1.2. Caution
2. Unpacking Instructions
3. Contents of the Box
4. Getting to Know the Parts of the Ripple Maker
5. Setting Up the Ripple Maker
5.1. Placement in the Shop
5.2. Power and Internet Connection
5.3. Setting Up and Using the Ripple Maker User Interface
6. Setting Up the Content Library
6.1. Choosing Content from the app.coffeeripples.com Website
7. Printing your Ripples
7.1. Placement and Orientation of the Coffee Cup
7.2. Choosing a Design and Printing
8. Maintaining the Ripple Maker
8.1. Replacing the Pod
8.2. Cleaning the Ripple Maker
9. Relocating/Transporting the Ripple Maker
10. TechnicalSpecicatione
11. Troubleshooting
12. Customer Support
13. General Product Safety Instructions
14. FCC Statement and Declaration of Conformity
3
3
3
4
4
5
6
6
6
7
9
9
9
10
10
11
11
13
16
16
17
18
19
Table of
Figures
Figure 3.1 Contents of the Box
Figure 4.1 Ripple Maker Front View
Figure 4.2 Ripple Maker Back View
Figure 4.3 Drip Tray View
Figure 5. 1 Plug in and Turn on the Ripple Maker
Figure 5.2 Wi-Fi Setup Screen
Figure 5.3 Registration Screen
Figure 54 AccountConrmationScreen
Figure 5.5 User Agreement Screen
Figure 5.6 Home Screen
Figure 7. 1 Placement and Orientation of Coffee Cup
Figure 7.2 Foam Height Illustrations
Figure 7. 3 Main Menu
Figure 7. 4 The Mobile Queue
Figure 7. 5 The Mobile Queue Tab
Figure 8. 2 Raise Tray for Cleaning
Figure 8. 3 Clean Drip Tray
4
5
5
5
6
7
7
7
8
8
10
10
10
11
11
14
14
Table of
Tables
Table 1. 1 Descriptions of Warning and Caution Symbols used in this Instruction Manual
Table10.1 TechnicalSpecications
Table 12. 1 List of Instructional Videos
3
16
18
3
01 Important Safety
Warnings and Cautions
Follow these basic precautions when using the Ripple
Maker to avoid electric shock, injury to persons, risk of
re and damage to the Ripple Maker.
Table 1.1
Descriptions of Warning and Caution Symbols used in this Instruction Manual
Symbol Description
Warning:
indicates actions or situations that could cause electric shock,
re,injuryordamagetotheRippleMaker.
Caution:
indicates actions or situations that could cause damage to the
Ripple Maker or its operator.
1.1 Safety Warnings
1 Read All Instructions.
2. Do not place the Ripple Maker, its cord or plug, in water or other liquids.
The Ripple Maker is water-resistant only.
3. Do not handle the cord or plug with wet hands.
4. Do not place the Ripple Maker in contact with hot surfaces.
5. Keep the Ripple Maker away from extreme temperatures and do not place in direct sunlight.
6. TheRippleMakercontainsmovingparts.Avoidplacingbodypartsclosetoprintingareastoavoidinjury.
7. Always turn off and unplug the Ripple Maker from the electrical outlet before cleaning or as instructed
in section 8.
8. Do not operate the Ripple Maker if its cord or plug are damaged or if the Ripple Maker is malfunctioning.
Call Customer Support for help. See section 12 for details.
9. Use cleaning materials and liquids recommended by Steam CC (see section 8.2). Not doing so may
causeinjury,re,electricshockordamagetotheRippleMakerandwillvoidthewarranty.
10. KeepyourhairandjewelryawayfromtheRippleMaker.
11. In case of an emergency, unplug the Ripple Maker.
12. Do not open the back service door. This action is dangerous and will void the warranty.
13. Keepngersawayinnormaluse,coversclosing-pinchingpossible.
1.2 Caution
1. The Ripple Maker is designed to print on foam surfaces only, please do not use this device for any
other purpose.
2. The manufacturer will not be responsible for misuse or mistreatment of the Ripple Maker.
3. The use of cartridges other than the original provided by Steam CC is forbidden, since this may cause
damage to the Ripple Maker and will void the warranty.
4
1Open the top
of the box. 2Remove shock-
absorbing materials. 3
Slide your hands
down the sides of the
Ripple Maker, place
your hands on the
upper enclosure of
the Ripple Maker and
lift from the box.
Safety Note:
The weight of the
product is 16 kg.
02 Unpacking
Instructions 03 Contents
of the Box
This section lists the items that are in the Ripple Maker package.
Check carefully to make sure you have all items on the list.
• 1 Ripple Maker
• 2 Pods
• 1 Power Cord and AC adaptor
• 1 Wi-Fi Dongle
• Instruction Manual
• Drip Tray
Figure 3.1: Contents of the Box
5
1
2
3
4
5
1. Touch Screen Display
2. Lid
3. Front Door
4. On/Off Button
5. Tray
6. Plug for Power Cord
7. Ethernet Port
8. Wi-Fi Dongle USB Port
9. Drip Tray
Figure 4.1: Ripple Maker Front View
04 Getting to Know the Parts
of the Ripple Maker
This section illustrates the dierent parts of the Ripple Maker.
6
7
8
Figure 4.2: Ripple Maker Back View Figure 4.3: Drip Tray View
9
6
05 Setting Up
the Ripple Maker
Thank you for purchasing the Ripple Maker! Now you can
print any text, design or even photograph on top of every
latte and cappuccino for the enjoyment of your customers.
This section includes information about:
• Where to place the Ripple Maker in your shop
• Connecting to AC power
• Inserting the Wi-Fi dongle or Ethernet cable
• How to navigate the user interface
Foravideoonthesubjectgotothe app.coffeeripples.com
website and view the "Quick Start" video.
When searching for a suitable location for the Ripple Maker in your shop, use the following guidelines:
• Place the Ripple Maker in accordance with the safety instructions.
See Section 1 for more details.
• Install close to an electrical outlet.
• Place the Ripple Maker on a level surface.
• Position the Ripple Maker in a convenient location for the barista,
keepinginmindtheworkowofthebaristaandotherpeople.
• Make sure the Ripple Maker is placed next to an Ethernet outlet or where there is good Wi-Fi signal.
• Ensure that the front of the Ripple Maker is facing the barista.
5.1 Placement in the Shop
5.2 Power and Internet Connection
1. Connect the power cord (A) to the power input
located at the back of the Ripple Maker. Plug the
other end into the wall outlet.
2. Unbox the Wi-Fi dongle and insert it in to the USB
port at the bottom of the Ripple Maker or connect
an Ethernet cable to the Ripple Maker.
Figure 5.1: Plug in and Turn on the Ripple Maker
Be sure that the Ripple Maker is placed on a stable and strong enough surface to support the Ripple Maker.
Follow safety
instructions regarding
the AC connection.
See section 1 for
more details.
7
ThersttimeyouareoperatingtheRippleMakeryouneedto
set up the Ripple Maker user interface.
Follow the steps listed below to complete the setup:
5.3 Setting Up and Using
the Ripple Maker User Interface
01
Switch on the Ripple Maker by pressing the
On/Off button at the base of the Ripple Maker
and wait for the system to boot up.
02
Select your Wi-Fi connection.
Figure 5.2: Wi-Fi Setup Screen
03
Please wait while the machine is being
registered.
Figure 5.3: Registration Screen
04
Conrmyourlocationandownership.
Figure 5 4: Account Conrmation Screen
Important: Never turn off your Ripple Maker
unless instructed otherwise. This will deny
automated maintenance procedures and will
damage the Ripple Maker.
8
05
The User Agreement is displayed on screen.
Please accept the agreement.
Figure 5.5: User Agreement Screen
06
Tap the "START" button and start using the
Ripple Maker.
Figure 5.6: Home Screen
07
Sincethisisyourrsttimeoperatingthe
Ripple Maker please see:
1. Chapter 8.1 "Replacing the Pod"
in order to install a new pod.
2. Chapter 8.2.4 "Cleaning the Drip
Tray" in order to install the drip tray.
9
06 Setting Up
the Content Library
The Content Library contains all of the Ripples that
you can print. This section explains how to edit your
Content Library using the web app.
6.1 Choosing content from the
app.coffeeripples.com website
Your content library already contains the basic themes and Ripples provided by Steam CC.
You can also download more Ripples and create your own.
1. To choose or create additional designs to use with the Ripple Maker,
go to the app.coffeeripples.com website.
2. Log in using your email and password, if you don't know your account details please contact
your system admin or your local manager.
3. On the side menu select "Ripples" and hit "New Ripple" on the right upper corner of the screen.
4. Now you can add any JPEG or PNG image you like by clicking the "Add image" button.
We recommend using high contrast images with bold lines.
5. Choose a name for your Ripple and hit "Create" on the bottom right side of the screen.
6. Now that you have created a new draft Ripple you need to submit it to your personal theme.
Under"DraftedRipples"ndyournewlycreatedRipple,hoverwiththepointerovertheRipple
imageandclickthe"Setting"icon,then"SubmitRipple"andnally"Submit".
7. Nowallthatisleftistoapprove(orreject)thesubmittedRipple.Thiscanonlybedonebythe
brand administrator.
Find your submitted Ripple under "Pending", click the "Setting" button then hit "Approve",
8. Your new Ripple is created and will be synced to your Ripple Maker's content library in a few
short minutes.
AnyrejectedRipplewillstayunder“RejectedRipples”untilit'sdeleted.
Watchthe"CreatingyourownRipples"videotolearnmoreonthesubject.
Print.
3
07 Printing your
Ripples
Printing is simple and follows these steps:
Place the coffee
cup in the center
of the tray.
1Choose a Ripple.
2
For a how-to video please go to the app.coffeeripples.com
website and view the "Preparing to Ripple" video.
Make sure you follow the instructions in this section
carefully in order to prevent damage to the Ripple Maker or
injurytopersons.
10
Place the cup in the center of the circle on the tray.
It is very important to use cups that are not larger than 4.25in/110mm (outer diameter)
and that the handles of the cup are no higher than the lip of the cup, as shown in below.
7.1 Placement and Orientation of the Coffee Cup
1. Not following these instructions could cause damage or injury.
2. The cup may contain a hot drink, therefore pay close attention to the start of the printing
and collect the cup immediately after the printing is completed.
7.2.1 Fast Print
7.2 Choosing a Design and Printing
This will immediately initiate the printing process.
Figure 7.1: Placement and Orientation of Coffee Cup
Figure 7.2: Foam Height Illustrations
The following illustrations show how the foam itself should be poured into the coffee cup
7.1.2 Foam Height Guidelines
foamespresso
perfect
foam height!
foam
too high
foam
too low
1. Choose the desired category from the bottom menu.
The Ripples that belong to that category will now be
displayed.
2. Choose a Ripple by swiping it left or right then tap
on it in order to print it.
Figure 7.3: Main Menu
Indice
