STEINEL IS D360-120 Manuale utente

IS D360-120

Installation Instructions

Commerical Occupancy Sensor

Consignes d'installation

Détecteur de présence à usage commercial

English

Français

Made in

Romania

RoHS

Compliant

110019627 10/2011 Technical changes subject to no prior notiﬁ cation.

STEINEL America Inc.

9O51 Lyndale Avenue South

USA - Bloomington, MN 55420

Tel: +1-952-888-5950

Fax: +1-952-888-5132

www.steinel.net

www.steinel.net (800) 852-4343 www.steinel.net (800) 852-4343

In this package

• IS D360-120 occupancy

sensor (switching module and

sensor module)

• Masking shrouds

• Fitting frame and securing

spring

• Installation instructions

Installation Overview

WARNING

• Turn power off at the circuit breaker before installing the sensor

• Sensor must be installed and used in accordance with appropriate

electrical codes and regulations

• Installation by a qualiﬁed electrician is recommended

Intended uses

• The sensor is intended to be

mounted directly to a lighting

ﬁxture or other listed enclosure

for the automatic switching of

lights.

Needed for installation

• 2 7/8 inch (73 mm) hole saw

• Wire nuts

Applications

• Fixture mounting in ofﬁces,

conference rooms, vestibules

and break rooms

Product Overview

120

VAC PIR

IP20

Product description

The STEINEL IS D360-120 is a

highly accurate ﬁxture mount

occupancy sensor for indoor

use. The sensor’s dimensions

are the same as those of a

MR16 lamp and ﬁt commercially

available MR16 ﬁtting frames.

The sensors use passive infrared

(PIR) technology to turn lighting ON

and off based on occupancy and

light levels.

www.steinel.net (800) 852-4343 www.steinel.net (800) 852-4343

Product Overview

2.1 in

1 - Fitting frame

2 - Catch

3 - Switching module

4 - Sensor module

5 - Shroud

6 - Securing spring

7 - Light level setting

8 - Time delay setting

120 VAC

0-300 Ballast or Tungsten

Fixture mount or listed enclosure;

mounts to standard MR 16 ﬁtting frame

5 seconds to 20 minutes

.2 - 200 fc, 2 - 2000 lux

360° with 180 angle of aperture

up to 26 ft (8m) reach *T, up to 13 ft (4m) reach *R

720

IP20 -4°F to +122°F, -20° C to +50°C

3.23 x 2.01 in, 82 x 51 mm

5 years

Voltage

Load Rating

Mounting

Time Delay

Light Level

Coverage

Detection levels

Switching zones

Environment

Dimensions

Warranty

UL and CUL Listed, RoHS Compliant

Speciﬁcations

*T = tangential coverage

*R = radial coverage

Product Overview

www.steinel.net (800) 852-4343 www.steinel.net (800) 852-4343

Mounting

Placement guidelines

• Detection lens must have a

clear, unobstructed view of

detection area; it does not

detect from behind obstacles,

such as walls or panes of

glass

• Ideal mounting height is 8-12

feet

• The site of installation should

be at least 20 inches away

from another light because

heat radiated from it may

activate the system

111

Installation

Conﬁrm power is off at the circuit

breaker.

• Depress the (2) catch (see

page 4) and separate the (3)

switching module from the (4)

sensor module

• Place the (3) switching module

in the (1) ﬁtting frame and

secure with the (6) securing

spring

• Pull back the springs of the

ﬁtting frame and place through

2 7/8 inch (73 mm) hole in

ﬁxture / mounting location

• Connect wiring

• Select desired time delay and

light level settings and snap the

sensor module back into the

switching module

www.steinel.net (800) 852-4343 www.steinel.net (800) 852-4343

Wiring

When installing, make sure power

has been switched off at the

breaker and check that the circuit

is dead with a voltage tester.

Black - Hot

White - Neutral

2 Red - Relay

Standard wiring:

Connect Black and one of

the Red wires to Hot (120VAC

input)

Connect White to Neutral

Connect other Red to Load

(120VAC output)

Operation

The IS D360-120 turns lighting on

and off automatically based on

occupancy. Adding a wall switch

provides manual on/off control.

Sensor operation

• Switch light ON (when light is

OFF): Turn switch OFF and ON

once. Light stays ON for the

period selected.

• Switch light OFF (when light

is ON): Turn switch OFF and

ON once. The light turns off or

switches to sensor mode.

Manual override

• Activate manual override: Turn

switch OFF and ON twice.

The lamp is set to stay on for

4 hours (red LED lights up

behind the lens). Then it returns

automatically to sensor mode

(red LED off).

• Deactivate manual override:

Turn switch OFF and ON once.

The light goes out or switches

over to sensor mode.

Light level function

The sensors incorporate a built-in

light level sensor which keeps

lighting off during daylight hours,

regardless of occupancy.

1 x

5 sec. – 20 min

2 x

4 h

Neutral

Hot

Black (Line)

Red (Relay)

White (Neutral)

Red (Relay)

www.steinel.net (800) 852-4343 www.steinel.net (800) 852-4343

Setup and Commissioning

Settings can be performed before

ﬁtting the sensor unit. If you wish

to change the settings again

after ﬁtting the sensor unit, the

catch must ﬁrst be released with

a ﬂat-bladed screwdriver and the

sensor unit must be removed (see

illustration below).

When this is done, the light

ﬁxture automatically switches to

continuous operation. On ﬁtting

the sensor unit, an approximately

45 second measuring phase is

initiated. The red LED ﬂashes

during this period.

Setup and Commissioning

Light level

The light level feature allows

lighting to remain OFF

during daylight, regardless of

occupancy. Daytime operation

is at 200 footcandles (factory

setting). Nighttime operation is

at .2 footcandles. Factory setting

is 200 fc.

The adjusting screw must be

set to daytime operation (200

fc) when adjusting the detection

zone and performing the function

test in daylight.

.2 – 200 fc

Time delay

Time delay is the period of time

lights remain on after the last

detection. Adjustment ranges

from 5 seconds to 20 minutes.

Factory setting is 5 seconds.

The shortest time delay setting is

recommended when adjusting the

detection zone and performing the

function test.

approx. 5 sec. – 20 min.

www.steinel.net (800) 852-4343 www.steinel.net (800) 852-4343

Setup and Commissioning

26 ft

Coverage size

With a mounting height of 8 ft (2.5 m),

the maximum reach of the sensor is

26 ft (8 m). The detection zone can be

optimally adjusted according to needs

(see below).

Minor motion coverage, typical for

an ofﬁce environment, is 13 ft (4 m)

radius. Coverage may vary depending

on mounting height and environmental

conditions.

Setup and Commissioning

Coverage adjustment - shrouds

The shrouds provided can be used for

masking out any number of lens segments

to shorten reach as required. Undesired

detection outside the desired detection

range can be eliminated.

The shroud can be separated along the

pre-grooved divisions in the vertical and

horizontal directions and applied to the

lens.

13 ft

13 ft 13 ft

26 ft

www.steinel.net (800) 852-4343 www.steinel.net (800) 852-4343

Troubleshooting

No power at the

sensor

Lights do not

switch ON

breaker has tripped or

is not switched ON

break in wiring

or short circuit

light level setting is in

nighttime mode during

daytime operation

lamp burned out

power is off

breaker has tripped

detection zone not

correctly adjusted

reset breaker, check

wiring with voltage

tester

check for proper

wiring connections

adjust light level

setting

replace lamp

turn power on at

circuit breaker

reset breaker

readjust

Problem Cause Remedy

Troubleshooting

Lights do not

switch OFF

Lights keep

switching ON/OFF

Lights switch ON

without obvious

movement

abundant heat from the

ﬁxture’s lamps is within

the detection zone and

keeps lights on as a

result of temperature

change

continuous movement

in the detection zone

switched on light is

within detection zone

sensor is detecting

movement outside of

the lighting zone

mount sensor below

the lamps

readjust zone or

apply shroud

adjust detection

zone or apply

shrouds

adjust zone or apply

shrouds

Problem Cause Remedy

www.steinel.net (800) 852-4343

M-15202-1

Warranty

STEINEL America warrants its

products against defects in

material or workmanship for a

period of ﬁve years. STEINEL will

replace or repair the item provided

that it has not been altered or

subjected to abuse, accident,

improper installation or improper

use. There are no obligations or

liabilities on the part of STEINEL

for consequential damages

arising out of or in connection

with the use or performance of

this product or other indirect

damages with respect to loss of

property, revenue, or proﬁt, or

cost of removal, installation or

reinstallation.

www.steinel.net (800) 852-4343

Dans ce kit

• Détecteur de présence

IS D360-120 (module de

commutation et module

de détecteur)

• Caches protecteurs

• Cadre de montage et ressort

de ﬁxation

• Consignes d'installation

Aperçu de l'installation

ATTENTION

• Couper le courant au niveau du coupe-circuit avant d'installer

ledétecteur

• Le détecteur doit être installé et utilisé conformément aux

codeset règlements applicables en matière d'électricité

• Une installation par un électricien qualiﬁé est recommandée

Usages prévus

• Le détecteur est destiné à

être directement monté sur

un support d'éclairage ou une

autre enceinte prévue pour

la commutation automatique

des lampes.

Éléments nécessaires à

l'installation

• Scie cloche 2 7/8 pouces

(73 mm)

• Écrous à ﬁls

Applications

• Montage sur support dans

les bureaux, les salles

de conférences, les halls

d'entrée et les salles de

pause

16 17

www.steinel.net (800) 852-4343 www.steinel.net (800) 852-4343

Aperçu du produit

120

VCA PIR

IP20

Description du produit

Le STEINEL IS D360-120 est

un détecteur de présence

monté sur support, d'une

haute précision, destiné à une

utilisation en intérieur. Ses

dimensions sont les mêmes

que celles d'une lampe MR16

et sont adaptées aux cadres

de montage MR16 disponibles

dans le commerce.

Les détecteurs utilisent une

technologie infrarouge passive

(PIR) permettant d'ALLUMER et

d'ÉTEINDRE l'éclairage en fonction

des niveaux de présence et de

luminosité.

Aperçu du produit

2.1 in

1 - Cadre de montage

2 - Loquet

3 - Module de commutation

4 - Module du détecteur

5 - Cache

6 - Ressort de ﬁxation

7 - Réglage de la luminosité

8 - Réglage de la temporisation

18 19

Indice

Lingue:

Altri manuali STEINEL Accessori

STEINEL

STEINEL IS 2180 ECO Manuale utente

STEINEL

STEINEL IS 180-2 Manuale utente

STEINEL

STEINEL SensorSchalter IR 180 AP Manuale utente

STEINEL

STEINEL GluePRO 300 Manuale utente

STEINEL

STEINEL IS 2180-5 Manuale utente

STEINEL

STEINEL GluePRO 300 Manuale utente

STEINEL

STEINEL IS 140-2 Manuale utente

STEINEL

STEINEL IS NM 360 Manuale utente

STEINEL

STEINEL luxmaster Manuale utente

STEINEL

STEINEL IR 180 Manuale utente

STEINEL

STEINEL IS 3180 Manuale utente

STEINEL

STEINEL Light Sensor Dual KNX Manuale del proprietario

STEINEL

STEINEL IS 3180 Manuale utente

STEINEL

STEINEL IR Micro LiveLink Manuale del proprietario

STEINEL

STEINEL IS 240 DUO Manuale utente

STEINEL

STEINEL L 330 S Manuale utente

STEINEL

STEINEL L 260 Manuale utente

STEINEL

STEINEL Control Pro IR Quattro MICRO DCS Manuale utente

STEINEL

STEINEL HBS 300 Manuale utente

STEINEL

STEINEL True Prescence KNX Manuale del proprietario

STEINEL

STEINEL IS 1 Manuale utente

STEINEL

STEINEL Studioline 400 Manuale utente

STEINEL

STEINEL IS 3360 Manuale utente

STEINEL

STEINEL HPD 2 IP Manuale utente

Manuali Accessori popolari di altre marche

Hillco

Hillco 2810 Manuale utente

Siemens

Siemens QSA2700D Manuale dell'operatore

Contours

Contours ZY024 Manuale utente

Saivod

Saivod VS621 Manuale utente

Virtuox

Virtuox VirtuCLEAN 2.0 Manuale utente

SCE

SCE ENVIRO-THERM SCE-TE170B24VSS Manuale utente

Z-Wave

Z-Wave HSD-200Z Manuale utente

turck

turck FMX-IM-2UPLI63FX Manuale utente

Decagon Devices

Decagon Devices 10HS Manuale utente

UPPAbaby

UPPAbaby Cup Holder Manuale utente

Elko

Elko SmartSensor Leakage Wireless Manuale utente

Grizzly

Grizzly H8371 Manuale utente

Panasonic

Panasonic HG-T Series Manuale utente

IFM Electronic

IFM Electronic Efector 250 Series Guida di riferimento

DigiDesign

DigiDesign 888/24 I/O Manuale utente

PROZIS

PROZIS QUAY Manuale utente

patagonia

patagonia PSI Vest Manuale utente

SFC Energy

SFC Energy EFOY GO! Manuale utente