Step Electric IAStar-S3 Manuale utente

Instruction Manual of

-S3 Inverter for Elevator

-S3 Series elevator-used inverters

Publication state: standard

Product version: V6.02

corporation

The information in this document is subject to change without prior

notice. No part of this document may in any form or by any means

(electronic, mechanical, micro-coping, photocopying, recording or

otherwise) be reproduced, stored in a retrial system or transmitted

without prior written permission from Shanghai STEP Electric

corporation

Shanghai STEP Electric corporation

Preface

The -S3 Series of elevator-used Inverters is a new type inverter which is

researched and developed based on the carry characteristic of elevator. The 32

bit electromotor-used Digital Signal Processing (DSP), Complex Programmable

Logic Device (CPLD), Intelligent Power Module (IPM) and the digiral vector

controlled frequency-variable speed-adjustable technology are used in the

Inverter. It also combines the model characteristic of potential energy. All of them

ensure stable, comfortable and efficient running of elevator.

Outline

This instruction manual describes installation, operation, function constants

setting, maintenance and trouble-shooting of the -S3 Inverter. The

manual can be the reference for designing the elevator control system by using

the -S3 Inverter. It also can be the reference of installation,

commissioning and maintenance of elevator.

Please read the manual carefully before installing and operating the inverter.

Reader

User

Designer of elevator control system

Maintenance engineer

Technical supporter

Innovations

a) The innovative starting compensation technique without load sensors

provides an excellently comfortable starting of elevator.

b) The new PWM dead-zone compensation technique can effectively reduce

motor noise and wearing.

c) There is no need to run autotuning for asynchronous motor.

d) There is no need to lift the car during self-tuning of the phase angle of

elevator with synchronous motor.

Instruction Manual of

-S3 Inverter for Elevator

Convenient and quick commissioning method of elevator

It is important whether it is convenient for elevator commissioning after wiring.

Usually it takes operators much time and effort to set many parameters and

perform complicated procedures. This becomes very convenient by using our

inverter which is designed especially for elevator. There are only three steps for

commissioning:

1 Adjusting running direction

The correct encoder wiring and motor running direction can be easily identified

by the operator.

2 Setting parameters

a) Users may use the leave-factory configuration of motor parameters directly

identified and/or set by us, or

b) Enter the motor parameters into the inverter according to the motor

nameplate.

3 Adjusting feeling

a) The comfortable feeling may be obtained by the leave-factory values of the

parameters.

b) This may be further improved through minor adjustments of C parameters

of PID.

Note on the content

The content of this manual may have supplements or modifications. Please visit

our website for upgrade: www.stepelectric.com.

IIIIII

Shanghai STEP Electric corporation

Safety Information

The following symbols with texts are used in this manual for safety-related

contents. Please comply with these regulations as they are very important.

Indicates precautions that, if not heeded, could

possibly result in loss of life or serious injury.

Indicates precautions that, if not heeded, could

possibly result in relatively serious or minor injury,

damage to the product, or faulty operation.

Indicates important information that should be

memorized.

Instruction Manual of

-S3 Inverter for Elevator

Table of contents

1OPERATION PRECAUTIONS ............................................................................................. 1

1.1 VOLTAGE CLASS AND MOTOR CAPACITY ...................................................................................... 1

1.2 CONFIRMATIONS UPON DELIVERY................................................................................................ 1

1.3 INVERTER SPECIFICATIONS ......................................................................................................... 1

1.4 INVERTER NAMEPLATE INFORMATION........................................................................................... 2

1.5 SAFETY PRECAUTIONS ............................................................................................................... 2

1.6 HANDLING NOTICE ...................................................................................................................... 4

1.6.1 Choice of Braking Resistor ................................................................................................... 4

1.6.2 Absorbing device is prohibited on the output side................................................................ 5

1.6.3 Operation Voltage of Inverter................................................................................................ 6

1.6.4 2-phase power supply is prohibited...................................................................................... 6

1.6.5 User control of output contactor ........................................................................................... 6

1.6.6 Altitude and derating operation............................................................................................. 6

1.6.7 Synchronous starpoint connection delay.............................................................................. 6

1.7 DISCARDING NOTICES ................................................................................................................ 6

1.7.1 Capacitor Disposal................................................................................................................ 6

1.7.2 Plastic Parts Disposal........................................................................................................... 6

2MODEL AND SPECIFICATION ........................................................................................... 1

2.1 INVERTER MODEL NUMBERS ....................................................................................................... 1

2.2 INVERTER TECHNICAL INDEX AND SPECIFICATION ......................................................................... 2

2.3 INSTALLATION DIMENSION AND WEIGHT OF INVERTER................................................................... 5

2.4 DIGITAL OPERATOR DIMENSIONS................................................................................................. 7

3INVERTER INSTALLATION................................................................................................. 1

3.1 INSTALLATION SITE ..................................................................................................................... 1

3.2 INSTALLATION ORIENTATION AND SPACE ...................................................................................... 2

3.3 INVERTER INSTALLATION ............................................................................................................. 3

3.4 REMOVAL AND INSTALLATION OF COVERS AND COMPONENTS OF INVERTER ................................... 3

3.4.1 Appearance and Components of Inverter............................................................................. 3

3.4.2 Removal and Installation of the Operator............................................................................. 4

3.4.3 Opening and Closing of the Terminal Cover......................................................................... 4

3.4.4 Removal and Installation of the Front Cover ........................................................................ 5

4INVERTER WIRING............................................................................................................. 1

4.1 CONNECTIONS TO PERIPHERAL DEVICES ..................................................................................... 2

Connection Diagram...................................................................................................................... 2

Wiring with peripheral devices....................................................................................................... 2

4.2 INVERTER TERMINAL WIRING ...................................................................................................... 7

4.2.1 Connection Diagram............................................................................................................. 8

4.2.2 Wiring Precautions ............................................................................................................. 10

4.3 WIRING MAIN CIRCUIT TERMINALS .............................................................................................11

4.3.1 Main Circuit Terminals .........................................................................................................11

4.3.2 Symbols and Functions of Main Circuit Terminals.............................................................. 12

4.3.3 Wire Sizes of Main Circuit .................................................................................................. 13

Shanghai STEP Electric corporation

4.3.4 Main Circuit Configurations ................................................................................................ 15

4.3.5 Illustration of Main Circuit Wiring ........................................................................................ 15

4.4 COUNTERMEASURES AGAINST NOISE ........................................................................................ 20

4.5 WIRING THE CONTROL CIRCUIT TERMINALS ............................................................................... 21

4.5.1 Control Circuit Terminals .................................................................................................... 21

4.5.2 Terminal Symbols of Control Circuit ................................................................................... 21

4.5.3 Control Circuit Terminal Functions...................................................................................... 22

4.5.4 Cable Specifications of Control Circuit Wiring .................................................................... 24

4.5.5 Control Circuit Terminal Wiring ...........................................................................................24

4.6 WIRING PG CARDS .................................................................................................................. 30

4.6.1 ABZ Increment PG Card for Asynchronous Motors............................................................ 30

4.6.2 SIN/COS PG Card for Synchronous Motors ...................................................................... 32

4.6.3 UVW Increment PG Card for Synchronous Motors............................................................ 35

4.6.4 Endat Absolute PG Card for Synchronous Motors ............................................................. 37

4.6.5 PG Card Terminal Wiring Precaution.................................................................................. 40

5DIGITAL OPERATOR........................................................................................................... 1

5.1 FUNCTION OF DIGITAL OPERATOR COMPONENTS ......................................................................... 1

5.1.1 LED Indicator ........................................................................................................................ 1

5.1.2 LED Digital Tube................................................................................................................... 2

5.1.3 LCD Display.......................................................................................................................... 2

5.1.4 Keyboard .............................................................................................................................. 2

5.2 OPERATION................................................................................................................................3

5.2.1 Power on and Initialization.................................................................................................... 3

5.2.2 Operation Mode.................................................................................................................... 3

5.2.3 【Run State】...................................................................................................................... 4

5.2.4 【Function Select】............................................................................................................. 6

5.2.5 【Parameter Modification】................................................................................................. 6

5.2.6 Examples of Parameter Setting............................................................................................ 7

5.3 FAULT INDICATION ...................................................................................................................... 8

5.4 CHINESE-ENGLISH COMPARISON OF PARAMETER NAMES OF THE OPERATOR ................................ 8

6FUNCTION PARAMETER LIST........................................................................................... 1

6.1 FUNCTION GROUPS.................................................................................................................... 1

6.2 FUNCTION LIST AND EXPLANATIONS ............................................................................................ 1

6.2.1 A (Advanced Menu) Parameters (R/W) ................................................................................ 1

6.2.2 B Parameters (R and R/W)................................................................................................... 7

6.2.3 C (PI Tune) Parameters (R/W) ........................................................................................... 12

6.2.4 D Parameters (R/W) ........................................................................................................... 16

6.2.5 E Parameters (Motor Parameters) (R/W)........................................................................... 19

6.2.6 F (Digital Input) Parameters (R/W) ..................................................................................... 22

6.2.7 G (Digital Output) Parameters (R/W).................................................................................. 25

6.2.8 H (Analog Input) Parameters (R/W) ................................................................................... 28

6.2.9 I (Analog Output) Parameters (R/W) .................................................................................. 30

6.2.10 J (Error Buffer) Parameters (R) ........................................................................................ 31

6.2.11 K (Function) Parameters (R/W) ........................................................................................ 33

Instruction Manual of

-S3 Inverter for Elevator

6.3 RUNNING STATUS U .....................................................................................错误！未定义书签。

7. APPLICATION OF ELEVATOR ...........................................................................................1

7.1 GENERAL................................................................................................................................... 1

7.2 SPEED CONTROL MODE ............................................................................................................. 4

7.3 WIRING BETWEEN ELEVATOR CONTROLLER AND INVERTER........................................................... 5

7.3.1 Analog Voltage Control Mode ...............................................................................................5

7.3.2 Analog Current Control Mode ...............................................................................................7

7.3.3 Multi-step Control Mode ..................................................................................................... 10

7.4 BASIC PARAMETER SETTING ..................................................................................................... 12

7.5 MOTOR AUTOTUNING................................................................................................................ 14

7.6 RUNNING DIRECTION ADJUSTMENT ........................................................................................... 16

7.7 ADJUSTMENT OF SPEED CURVE ................................................................................................ 19

7.8 ADJUSTMENT OF COMFORT....................................................................................................... 22

7.9 ADDITIONAL FUNCTIONS ........................................................................................................... 28

8. FAULT INSPECTION ........................................................................................................... 1

8.1 PROTECTIONS AND INSPECTIONS ................................................................................................ 1

8.2 WORKFLOW OF FAULT DIAGNOSIS ............................................................................................... 4

9. SERVICING AND MAINTENANCE...................................................................................... 1

9.1 GUARANTEE PERIOD .................................................................................................................. 1

9.2 PRODUCT INQUIRY ..................................................................................................................... 2

9.3 DAILY INSPECTION...................................................................................................................... 2

9.4 PERIODIC INSPECTION ................................................................................................................ 2

Appendix A Electromagnetic Compatibility .................................................................................................... 1

A.1 Noise Restraint ............................................................................................................................... 1

A.1.1 Noise Type...................................................................................................................................... 1

A.1.2 Noise Transmission ........................................................................................................................ 2

A.1.3 Basic Countermeasures for Noise Restraint................................................................................... 2

A.2 Wiring Requirements ...................................................................................................................... 3

A.2.1 Cable laying.................................................................................................................................... 3

A.2.2 Cable cross-section area ................................................................................................................ 4

A.2.3 Shielded cable ................................................................................................................................ 4

A.2.4 Installation of shielded cable........................................................................................................... 4

A.3 Grounding....................................................................................................................................... 5

A.3.1 Grounding method .......................................................................................................................... 5

A.3.2 Grounding precautions ................................................................................................................... 6

A.4 Surge Absorber installation ............................................................................................................. 6

A.5 Leakage Current and Countermeasures......................................................................................... 7

A.5.1 Leakage current to earth................................................................................................................. 7

A.5.2 Leakage current between lines....................................................................................................... 7

A.6 Restraint of Radiation from Inverter ................................................................................................ 7

A.7 Application of Filter for Power Lines ............................................................................................... 8

A.7.1 Functions ........................................................................................................................................ 9

A.7.2 Installation of Filter for Power Lines................................................................................................ 9

A.8 EMC Installation Areas ................................................................................................................... 9

VIIVII

Shanghai STEP Electric corporation

VIII

A.9 Precautions for Inverter Electric Installation..................................................................................11

A.10 EMC Standards of -S3 Inverter ..................................................................................... 12

Appendix B Lists of Function Parameters, Running Status and Faults ......................................................... 1

B.1 Function Parameter ................................................................................................................................ 1

B.2 Running Status List............................................................................................................................... 14

Appendix C Conformities of the Inverter ....................................................................................................... 1