Steren CAR-210 Manuale utente
Before using your new SD & flash drive MP3 encoder car stereo,
please read this instruction manual to prevent any damage. Put it
away in a safe place for future references.
IMPORTANT
Do not try to open the equipment, may be exposed to dangerous
radiation.
Warranty is void if you open the case.
In order to reduce the risk of electrical shock, do not remove the device’s
cover
Do not expose the equipment to extreme weather.
Do not use or store the equipment near wet places. May cause
malfunction or shock hazard.
Do not touch the contacts on the front panel or the main body, may
result in poor electrical contact.
Clean only with a soft, dry cloth.
Install the equipment in a place where cannot interfere with driving.
Wire and test the cables temporally before to install the equipment
permanently.
Refer to qualified personnel for any needed technical service.
If the installation angle exceeds 30° horizontally, the unit may not works
appropriately.
CONTROLS
ENGLISH
ENGLISH-2
B
efore usin
g
y
our new SD & flash drive MP3 encoder car stereo,
pl
ease rea
d
t
hi
s
i
nstruct
i
on manua
l
to prevent an
y
d
ama
g
e.
P
ut
i
t
a
way in a safe place for future references
.
1
2
3
4
56
7
10
11 12
13 14 15 16 17 18 19
20 21
22 25
26
8
923 24 27
1.- On / Off
Press and hold for 2 seconds to power the car stereo on. Press and hold
2 seconds to power it off.
2.- Release
Press to release the frontal panel
3.- Volume / Selector
Allows you to set the volume level (turn it right or left)
Press to switch between:
Bass: Set the bass frequencies
Treble: Set the treble frequencies
Balance: Allows you to select the left speakers, right speakers
or both
Fader: Use to select the frontal, rear or both speakers
Press and hold for 3 seconds and you will see in the screen:
DSP Off: allows you to select one of predetermined EQ: Rock,
Classic, Flat, Pop or Off.
ESP: Select between 12 or 45 seconds of ESP
Beep: Use to activate or deactivate the button beep
Seek: Switch between Seek 1 and Seek 2
Press the Selector button each time you want to switch between
different modes.
4.- Mute
Press once to mute the sounds. Press again to return normal play.
5.- Mode
Press to switch between: CD, Aux, memory card / USB memory
6.- Display
In MP3, CD, memory card or flash memory mode, press DISP to show
the current time for 5 seconds
If you are in Clock mode, press and hold DISP for 2 seconds, to set the
current time. The clock will blink, move the selector button to the right to
set the hour, move it to the left to set the minutes, finally press DISP to
store the changes.
7. LCD screen
Display several information
ENGLISH
ENGLISH-3
P
ress the Selector button each time
y
ou want to switch between
d
ifferent modes
.
8.- Sensor
Lights on when the frontal panel is out of the main body
9.- Restart
Press this button when:
- The initial installation is completed
- Function buttons do not operate
- An error is displayed in the screen
Remember, you must use a thin metal object to press the button, but do
not use any sharp object.
If the equipment does not work even if you pressed the Restart button,
use an alcohol damped Qtip to clean the contact located behind of the
frontal panel.
10.- Band
In radio mode, press band to switch between different radio bands: FM1,
FM2, FM3, AM1, AM2.
11.- Tune seek / Track
In radio mode allows you to seek the next frequency
In CD mode, jumps to next track
12.- Tune seek / Track
In radio mode allows you to seek previous frequency
In CD mode, jumps to previous track
13.- Automatic memory storing
Press and hold AMS and the device will search the strongest radio
signals, automatically will be stored in the preset memories (up to 6
memories)
Press AMS once to search into the stored radio stations
14. Play / Pause / Memory 1
Play a song contained in a CD, flash memory or SD card
Pause a song
In radio mode allows you to access the memory 1
15.- Intro / Memory 2
In CD mode you can listen the first 10 seconds of each song contained
in the CD
If you want to listen a complete song, press Play once
In radio mode press to get access to memory 2
16.- Repeat / Memory 3
In CD mode allows you to activate the repeat function, repeat all disc or
deactivate the function.
In Radio mode allows you to get access to memory 3
ENGLISH
ENGLISH-4
17.- Random / Memory 4
In CD mode allows you to play the songs, randomly. RDM word displays
in screen.
In Radio mode allows you to get access to memory 4
18.- Memory 5
In Radio mode allows you to get access to memory 5
19.- Memory 6
In Radio mode allows you to get access to memory 6
20.- Stereo / Mono
In radio mode press to switch between Stereo or Mono audio output
While playing a song, press to select the left, right or stereo output
sound
21.- LOC / DX
Press LOC to select the reception of a strong or weak radio signal. If
you press LOC once, you will listen to local radio stations, only and LOC
word displays in the screen. Press LOC once again, and you will switch
to DX mode, where you can listen to local and distance radio stations (if
available)
22.- Loudness
Press to activate or deactivate the loudness function
23.- Eject
Press to eject a CD
24.- CD slot
Use to insert a CD
25.- IR sensor
IR remote control sensor
26.- Mini USB connector
Allows you to plug an USB device which contain music
27.- SD slot
Allows you to insert a SD card which contain music
ENGLISH
ENGLISH-5
REMOTE CONTROL
1.- On / Off
Press to power the car stereo on / off.
2.- Play / Pause / Memory 1
Play a song contained in a CD, flash memory or SD card
Pause a song
In radio mode allows you to access the memory 1
3.- Intro / Memory 2
In CD mode you can listen the first 10 seconds of each song contained
in the CD
If you want to listen a complete song, press Play once
In radio mode press to get access to memory 2
ENGLISH
ENGLISH-6
+
-
DN
DN UP
SEL
DISP A.P. ST
MODE BAND LOC LOUD
SCN
123
456
1
2
34
5 6 7
8
9
10
11
12
13
14
15
16
1718 19
18
9
4.- Repeat / Memory 3
In CD mode allows you to activate the repeat function, repeat all disc or
deactivate the function.
In Radio mode allows you to get access to memory 3
5.- Random / Memory 4
In CD mode allows you to play the songs, randomly. RDM word displays
in screen.
In Radio mode allows you to get access to memory 4
6.- Memory 5
In Radio mode allows you to get access to memory 5
7.- Memory 6
In Radio mode allows you to get access to memory 6
8.- Mute
Press once to mute the sounds. Press again to return normal play.
9.- Volume
Set the volume level
10.- Mode
Switch between: Radio, CD, AUX; Memory Card / USB Card
11.- Stereo / Mono
In radio mode press to switch between Stereo or Mono audio output
While playing a song, press to select the left, right or stereo output
sound
12.- Loudness
Press to activate or deactivate the loudness function
13.- Scan
Press this button to scan the strongest radio frequencies
14.- Display
Displays the current hour
15.- A.P.
Press to switch between stored radio stations
16.- LOC / DX
Press LOC to select the reception of a strong or weak radio signal. If
you press LOC once, you will listen to local radio stations, only and LOC
word displays in the screen. Press LOC once again, and you will switch
to DX mode, where you can listen to local and distance radio stations (if
available)
ENGLISH
ENGLISH-7
17.- Band
In radio mode, press band to switch between different radio bands: FM1,
FM2, FM3, AM1, AM2.
18.- Tune seek / Track
In radio mode allows you to seek a frequency
In CD mode, jumps to previous / next track
19.- Selector
Press to switch between:
Bass: Set the bass frequencies
Treble: Set the treble frequencies
Balance: Allows you to select the left speakers, right speakers
or both
Fader: Use to select the frontal, rear or both speakers
INSTALLATION
This equipment can be mounted on the dashboard. Be sure to mount
the unit firmly. If installation requires hole drilling or another
modifications to the vehicle, contact with your nearest dealer.
1.- Remove the external cover from the car stereo.
2.- Insert the supplied keys on each side of the car stereo until you hear
a click.
ENGLISH
ENGLISH-8
3.- Remove the holder and place it on the dashboard.
4.- Connect wires (Refer to Wire Connections).
5.- Install the rear holder.
6.- Place the main body into the holder.
7.- To finalize, replace the external cover.
If you want to remove the frontal panel:
1.- Press Release button. The panel will be folded down.
2.- Be careful when remove the frontal panel, do not press on the LCD
screen. Move to the right and pull out.
ENGLISH
ENGLISH-9
3.- Enclose the front panel for safe keeping into the supplied protective
case.
To replace the front panel:
1.- Put the right hole from the frontal panel into the main body.
2.- Press to the right and place the left hole from the frontal panel into
the main body left contact, press until you hear a click.
3.- Fold up the frontal panel.
ENGLISH
ENGLISH-10
Indice
Lingue:
Altri manuali Steren Ricevitore per auto
