STI STI-6400 Manuale utente

TI-6400 Exit topper®

IN TRUCTION MANUAL

“We Protect The Things That Protect You.”

afety Technology International, Inc.

Features:

• Helps prevent both unauthorized exits and entries

through emergency exit doors.

• Easy to install.

• Less expensive than heavy horizontal bar type units and

practical for all emergency doors.

• May be mounted on top, right, left or next to almost any

door.

• User can select onsite whether to use an alarm or

annunciator.

• Contact STI for custom applications .

TABLE OF CONTENT

WARNING

All units are recommended for indoor use. Unit must be tested periodically to verify the life of

battery. STI recommends you change the 9 Volt battery twice a year. Installer may need to

purchase a simple audio-meter, typically available at your local electronics store, to measure the

sound in areas where the alarm is expected to be heard during normal noise environment.

Results from this test may prove it beneficial to purchase additional exit stopper units. When

purchasing a remote unit (STI-6403) you will need to periodically test the connections to make

sure audibles function at a sound level to alert staff. Maximum of three STI-6403 may be used

in parallel.

All specifications and information shown are current as of publication and subject to change

without notice.

• Warnings and Cautions ................................................................................................Page 2

• Warranty Information ..................................................................................................Page 2

• Specifications ................................................................................................................Page 3

1. Dimensions ..............................................................................................................Page 3

2. Polycarbonate ..........................................................................................................Page 3

3. Electronics ................................................................................................................Page 3

4. Remote Horn ............................................................................................................Page 3

• Circuit Board Set-Up......................................................................................................Page 4

• Terminal Strip Layout....................................................................................................Page 4

• Switch Settings..............................................................................................................Page 4

• Alarm Feature Description............................................................................................Page 5

• Installation Instructions All Units / STI-6400 ..............................................................Page 5

• Mounting Options ........................................................................................................Page 6

• STI-6402 Double Door additional install notes ........................................................Page 7

• STI-6403 Remote Horn additional install notes ......................................................Page 7

• STI-6404 Double Door with Remote Horn additional install notes ........................Page 7

• STI-6405 Exit Stopper with Momentary Reset ........................................................Page 7

WARRANTY INFORMATION

Three year guarantee against breakage of polycarbonate in normal use (one year on electro

mechanical and electronic components).

PECIFICATION

Polycarbonate Enclosure:

Dimensions 5.375” W x 5.375” H x 2 “ D (137mm x 137mm x 51mm)

Flammability: UL94 V-2

Wall Thickness: 0.12 in (3.05mm)

Electronics: TI-6400 - All Units

9 VDC Alkaline or 9V-24VDC wired

Class II UL Listed transformer

Horn Volume at 1 ft. 95 dB low / 105 dB high

Relay Output Form C Dry Contacts 0-30 VDC or VAC, 1 Amp

Stand by Current 10uA

Alarm Current 130mA at 95 dB / 200mA at 105 dB

Electronics: TI-6403 and TI-6404 - Remote Horn Unit

Power Source 9 VDC Operating Power* only

Horn Volume at 1 ft. 95 dB low / 105 dB high

Stand by Current 0 A

Alarm Current 50mA at 95 dB/ 200 mA at 105 dB

*Power source for the STI-6403 Remote Horn uses a separate power source from the STI-6400

alarm. The Remote Horn contains an internal 9 volt battery. Horn operates when the Form C

contact at main unit is activated on alarm.

Power Source

JP5

JP2

JP4

JP3

JP7

SWITCH

ALARM

DURATION

ALARM VOLUME SWITCH

TRIP DELAY SWITCH

ARMING SWITCH

(FACTORY DEFAULT SETTINGS)

(ON)

(OFF)

TERMINAL BLOCK

WITCH ETTING

CIRCUIT BOARD ET-UP

Volume - High (105 dB) at 1 ft. ON*

Volume - Low (95 dB) at 1 ft. OFF

Duration - 30 Second Alarm OFF* OFF*

Duration - 180 Second Alarm OFF ON

Duration - Continuous Alarm ON OFF

Duration - Annunciator Mode ON ON

Trip - Immediate OFF*

Trip - 15 Second Delay ON

Arming - Immediate ON*

Arming - 15 Second Delay OFF

FEATURE JP2 JP3 JP4 JP5 JP7

*Factory Settings

Note: Slide black lever to desired ON/OFF position as labeled on circuit board.

NC COM NO GD V+ RS1 RS2 KEYSW

TERMINAL BLOCK WIRING CONNECTIONS

FORM C

DRY

CONTACTS

REMOTE

POWER

INPUT

9-24 VDC

REED

SWITCH

TERMINALS

KEY SWITCH

TERMINALS

FIGURE 1

IN TALLATION IN TRUCTION

Note: STI recommends setting up unit and testing settings prior to mounting.

1. Make sure key switch is in the OFF

position.

2. Remove tamper screw on side of

unit and remove housing cover.

Save this tool for future servicing

and battery change (Figure 2).

3. Set switches, on circuit board, to

desired alarm settings (figure 1).

4. Test settings by connecting battery

or external power source. If using

external power source a Class II UL

Listed transformer is required. If

power is present at terminal block

(figure 1) 9V battery is in no-load

on standby power consumption.

19039 SCREW

6 x 1 1/4 in.

(2) PROVIDED

19018 ANCHOR

(2) PROVIDED

BOTTOM SURFACE AS SHOWN

WIRES THROUGH NOTCH ON

AND ROUTE REED SWITCH

REMOVE FRONT COVER

VIEW SHOWING MAGNET INSTALLATION

MAGNET

MAXIMUM GAP 3/4 in. (19mm)

3/8 in. (9.5mm) ON METAL DOOR

AND FRAME

SPACERS (USE AS NECESSARY)

NOTE: 2 SPACERS UNDER BOTH

MAGNET AND REED SWITCH

MUST BE USED ON STEEL DOORS

FIGURE 2

FIGURE 3

ALARM FEATURE DE CRIPTION

• Volume witch JP2 - Sets alarm volume to high 105 dB or low 95 dB.

• Duration witch JP3 and JP4 - Amount of time alarm sounds after trip. Arming resets at end

of duration if door is closed. Alarm will not reset if in continuous mode; alarm sounds until

battery is drained. Annunciator Mode is a series of 10 short beeps or until door is closed.

• Trip Delay witch JP5 - If you wish to ENTER an alarmed door without sounding the horn

immediately, the trip delay will allow 15 seconds for you to enter and de-activate the alarm

with the key switch before the alarm will sound.

• Arming witch JP7 - This mode is useful when an AUTHORIZED EXIT is required through

alarmed door. In “ON” position immediate arming will set the alarm ready to function as soon

as door is opened. In “OFF” position delay arming will allow 15 seconds for you to exit through

the door without sending alarm signal.

5. Mount main unit on or next to door using

hardware provided. Reed switch mounting

locations can be moved to one of the four

positions shown in figure 2. If mounted

next to door, route reed switch wire

through knockout in bottom of housing as

shown in figure 3.

6.Mount magnet on door frame (or door if

unit is mounted next to door) using screws

provided. When mounting on metal doors

or door frames, use plastic spacers

provided. Reed switch and magnet must

be within 3/4” when door is closed (3/8”

on metal door and frame). Please refer to

figures 4, 5 and 6 on page 6 for other

mounting options.

7. If installing STI-6402, STI-6403, or STI-6404

continue to page 7 for more instructions

(Figures 7 and 8). STI-6402 mounting

option is shown on page 6.

8. Replace cover by sliding flanges on inside

of cover into slots on base. Then rotate the

cover over unit and snap close. Replace

tamper screw.

FLANGES SLOTS

TERMINAL STRIP

9 VOLT BATTERY

19011 TAMPERPROOF SCREW

(1) PROVIDED

19016 TAMPER WRENCH

(1) PROVIDED

BASE

COVER

19014 MOUNTING SCREW

(4) PROVIDED

EMERGENCY EXIT ONLY

STOP

ALARMSOUNDSWHENDOORISOPENED

OFF

MOUNTING OPTION

DOOR

DOOR STOP

JAM

MAGNET

6400 UNIT

MAGNET MUST BE

INSTALLED OPPOSITE

RAISED RIB ON OUTER COVER.

SPACERS - USE

AS NECESSARY

19018 ANCHOR

(2) PROVIDED

TYPICAL FLUSH MOUNT DOOR JAM

INSTALLATION

DOOR

SWING

NOTE: 2 SPACERS MUST BE

USED ON STEEL DOORS

19039 SCREW

6 x 1 1/4 in.

(2) PROVIDED

MAGNET

6400 UNIT

DOOR STOP

SWING

DOOR

TYPICAL RECESSED MOUNT DOOR JAM

INSTALLATION

3/4 in. [19 mm]

MAXIMUM GAP

3/8 in. [9.5mm] ON

METAL DOOR AND FRAME

MAGNET ASSEMBLY

(SEE ABOVE FOR INSTALLATION)

FIGURE 5

FIGURE 4

*Note: W en mounting reed switc on door and t e main unit on wall, wire service loop must be used.

FIGURE 6

TYPICAL DOUBLE DOOR INSTALLATION

STI-6402

TI-6402 DOUBLE DOOR IN TALL NOTE

TI-6403 REMOTE HORN IN TALL NOTE

STI-6403 REMOTE HORN UNIT INSTALLATION

ROUTE WIRES

THROUGH NOTCH KEY SWITCH

06402 REED SWITCH

(RS1)

06402 REED SWITCH

(RS2)

OPTIONAL:

TO REMOTE

HORN

STI-6403

VIEW SHOWING INSTALLATION OF

ADDITIONAL REED SWITCH 06402

TO KEY

SWITCH

TERMINAL BLOCK

FIGURE 7

FIGURE 8

1. Remove cover.

2. Connect two conductor wire (14-24 AWG)

from main unit terminal block pins COM and

NO to remote horn unit terminal block.

(wire not provided). Units can be set up to

300 ft. apart. Not polarity sensitive (refer to

Fig. 1 and Fig. 7 for details).

3. Connect internal battery.

4. Mount similar to main unit with #8 x 1 in.

screws and anchors if necessary.

5. Replace cover and screws.

6. Turn key switch to ON position.

*Note: The ON/OFF key position is opposite

from 6400 main unit. Remote horn sounds

when main unit alarm is activated.

1. Determine length needed for reed

switch wires. STI provides 6 ft. which

can be cut to desired length.

2. Connect first reed switch in RS1 and

second in RS2 (Figure 7). (Refer to

Figure 1 for additional details on

page 4.)

3. If not using extra reed switch, add

jumper across two terminals of RS2

on terminal block.

*Note: Alarm will sound when either

door is opened.

TI-6404 DOUBLE DOOR WITH REMOTE HORN IN TALL NOTE

The STI-6404 is a combination unit for double doors with a remote horn. Reference the

installation instructions for the main unit, the STI-6402 and the STI-6403 for complete

installation.

TI-6405 EXIT TOPPER WITH MOMENTARY RE ET

The STI-6405 uses a momentary switch. After initial installation, unit

is always on and you do not have to remember to turn it on when

you leave a protected area. This model also eliminates having to

remember to re-arm it because it is never off.

When the alarm is triggered, to silence the alarm, insert the key and

turn completely to the "RESET" position and hold for 2 seconds, then

release. The switch will spring back to its original position and push

the key out. To turn the unit off, supply power must be removed.

RESET

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali STI Sistema di sicurezza

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente