Stid Spectre Guida di riferimento

Installation

procedure

Notice

d’installation

Manual de

instalación

SPECTRE Access UHF

Read only & osdp

Installation procedure

UHF SPECTRE Access

Lecture seule & osdp

Notice d’installation

UHF SPECTRE Access

Solo lectura & osdp

Manual de instalación

SPECTRE Module Access - SMA

SPECTRE Reader Access - SLA

Frequency Band

References

Frequency Band

References

865 - 868 MHz

SMA-R41-A-U04-xx: TTL

SMA-R42-A-U04-5AB: RS232

SMA-R43-A-U04-7AB: RS485

SMA-W43-A-U04-7OS: osdp

865 - 868 MHz

ERP: 2W

SLA-R41-A-U04-xx: TTL

SLA-R42-A-U04-5AB: RS232

SLA-R43-A-U04-7AB: RS485

SLA-W43-A-U04-7OS: osdp

902 - 928 MHz

SMA-R51-A-U04-xx: TTL

SMA-R52-A-U04-5AB: RS232

SMA-R53-A-U04-7AB: RS485

SMA-W53-A-U04-7OS: osdp

902 - 928 MHz

EIRP: 4W

SLA-R51-A-U04-xx: TTL

SLA-R52-A-U04-5AB: RS232

SLA-R53-A-U04-7AB: RS485

SLA-W53-A-U04-7OS: osdp

Morocco

867.7-867.9 MHz

SMA-R41-A-U04-xx1M: TTL

SMA-R42-A-U04-5AB1M: RS232

SMA-R43-A-U04-7AB1M: RS485

SMA-W43-A-U04-7OS1M: osdp

Morocco

867.7-867.9 MHz

ERP: 0.5W

SLA-R41-A-U04-xxM: TTL

SLA-R42-A-U04-5ABM: RS232

SLA-R43-A-U04-7ABM: RS485

SLA-W53-A-U04-7OSM: osdp

Peru

916-928 MHz

SMA-R51-A-U04-xx1PE: TTL

SMA-R52-A-U04-5AB1PE: RS232

SMA-R53-A-U04-7AB1PE: RS485

SMA-W53-A-U04-7OS1PE: osdp

Peru

916 - 928 MHz

EIRP: 4W

SLA-R51-A-U04-xx1PE: TTL

SLA-R52-A-U04-5AB1PE: RS232

SLA-R53-A-U04-7AB1PE: RS485

SLA-W53-A-U04-7OS1PE: osdp

Power Supply Characteristics - SMA /SLA

Use an AC/DC power supply LPS type, Limited Power Source (as per IEC EN 60950-1 Ed2) or ES1 type, PS1 (as per IEC EN 62368-1) for main supply and for

an eventual V+/V-.

Main power supply: Range +9 Vdc up to +36 Vdc Typical: 12 Vdc

Consumption: Typical: 1A under +12 Vdc Max: 1.5A under +12 Vdc

Characteristics - SMA / SLA

Communication: RS485 (L+ & L-) / RS232 (TD & RD) / TTL (Wiegand / Clock & Data)

Pin out: Removable connectors 3x4 pins and 1x8 pins, thread 3.81 mm / 0.149 in

Temperature: -25 to +60 °C / -13 to +140 °F

Protection: IP66 level

Chip: EPC1 Gen2 (ISO 18000-63) - 1 to 62 bytes max

I/O: 4 optocoupled inputs and 4 optocoupled outputs

Module LED: 1 red LED: presence of power supply and 1 green LED: activity on Reader / host link

Antenna LED: 7 configurable colors (red, green, blue, orange, purple, turquoise, white)

Recommended Cables - SMA / SLA

RS485: Use a multi-conductor shielded twisted pair cable. Max lenght 3 280 ft / 1000 m at 9600 baud.

RS232: Max length 49.21 ft / 15 m.

Wiegand / Clock & Data: Use a multi-conductor shielded untwisted

2 cable AWG24 –30 m / 98.4 ft max

4 cables AWG24 –60 m / 196.9 ft max

6 cables AWG24 –100 m / 328.1 ft max

2 cable AWG20 –50 m / 164. ft max

4 cables AWG20 –100 m / 328.1 ft max

Recommendations - SMA / SLA

▪Install the module/reader away from computer transmission cables or from power sources (ex: RJ45, sector…).

The disruptions that they can cause can vary according to their radiation power and their proximity.

▪Use a filtered and regulated power supply.

▪Antennas connected to different modules/readers may interfere with each other. Move them away from each other.

▪A power supply which provides 1.5 A min under +12Vdc is recommended.

If the IN/OUT are powered by the module, use a 2A min under +12Vdc power supply.

▪Users must not remain within a range of less than, 34 cm / 13.39 in from an antenna for an extended period of time as per EN50364 applicable to this

type of device.

▪Apart from the hatch the module housings must not be opened.

▪Before any service operation you must de-energize reader.

▪Check that the hatch seal is correctly positioned before closing.

▪Do not remove the caps of unused

cable glands:

▪Do not remove the caps from the unused

RF connectors:

▪Install the module/reader with the word UP

facing upwards so that the connectors are down:

Host Connection Access - SMA / SLA

In order to access the module/reader connectors, open only the hatch provided for this purpose by unscrewing the 4 captive screws without removing them from

the hatch.

SPECTRE Access UHF

Read only & osdp

Installation procedure

UHF SPECTRE Access

Lecture seule & osdp

Notice d’installation

UHF SPECTRE Access

Solo lectura & osdp

Manual de instalación

Front View of the Module - SMA / SLA

TTL / RS232 / RS485 / I/O Connection - SMA / SLA

Configuration - SMA / SLA

The number of antennas, the number of channels and the communication protocol are configurable with the Ultrys V2 application or when the module is ordered.

▪TTL protocols (Wiegand & ISO2):

- ISO2 (Clock & Data) - Decimal (7 bytes max)

- Wiegand 26-bit

- Wiegand with LRC - Hexadecimal (12 bytes max) + LRC

- Wiegand without LRC - Hexadecimal (12 bytes max)…..

▪Serial protocols (RS232 & RS485): The structure of the frame can be configured with the following optional parameters (in gray):

1 byte

1 byte + X bytes

1 byte

STX

Channel number + Tag Data*

LRC

ETX

0x02

0x0y nn…..nn

0x0D

0x0A

0x03

- STX+ETX: add 0x02 (STX) and 0x03 (ETX) at the start /end of frame - CR/LF: Carriage Return (0x0D + 0x0A) configurable separately

- LRC: Checksum (XOR of all previously bytes except STX) - Data sent in: decimal or hexadecimal

- ASCII: if this option is activated, the data will be sent in ASCII mode (data size will be doubled) - Non-significant zero: complete the tag data with not

significant 0 to obtain the defined data size - (Channel no. + 0 padding + tag data, etc.).

▪osdp protocol (RS485: 7OS): refer to Spec_Protocole_7OS_OSDP_UHF-US.pdf

Red LED

Green LED

Cable glands (Data Bus-Power sup. - Input/Output)

RF port 1

RF port 2

RF port 3

RF port 4

End of line resistor RS485

Use this (on RS485 connection) when the distance of the data cable is near or over

100 m / 328.08 ft and the signal is weakened (polluted signals, frame errors etc.).

TTL output level: +5V or Vin

Micro USB connector for configuration purposes only

J14

Use this connector for earth connection purpose

IN 1-2-3-4

4 opto-coupled inputs

OUT 1-2-3-4

4 opto-coupled outputs

V- opt

Low polarization potential of opto-coupled inputs and outputs

V+ opt

High polarization potential of opto-coupled inputs and outputs

DATA1

Data or D0 Channel 1 or Tx (RS232) or L+ (RS485)

CLK1

Clock or D1 Channel 1 or Rx (RS232) or L- (RS485)

DATA 2 / CLK2

Data/Clock or D0/D1 Channel 2

DATA 3 / CLK3

Data/Clock or D0/D1 Channel 3

DATA 4 / CLK4

Data/Clock or D0/D1 Channel 4

ALIM

Power supply

GND

SPECTRE Access UHF

Read only & osdp

Installation procedure

UHF SPECTRE Access

Lecture seule & osdp

Notice d’installation

UHF SPECTRE Access

Solo lectura & osdp

Manual de instalación

Wall

Pole

Start Sequence - SMA / SLA

When the reader is switched on: the reader’s red LED lights up. Reader initializing.

After initializing, the reader will look for a configuration tag for about 15 s, on antenna 1 (connected to RF port 1).

•If no tag detected: the antenna LED flashes “color RFON”(200ms) (blue by default) / RFOFF (200ms).

•If any tag detected: the antenna LED displays the sequence “color RFON”(blue by default) / “color DETECTION”(orange by default) for 200ms then LED OFF.

•If a configuration tag is detected: the antenna LED displays the sequence « color RFON “(blue by default) / “color DETECTION”(orange by default) for 200ms

then LED OFF then the antenna LED gives the followings indications:

•3 GREEN flashes (500ms ON; 200ms OFF): the configuration tag is taken into account.

•3 RED flashes (500ms ON; 200ms OFF): the regulation (region) of the configuration tag does not match to the regulation of the reader.

•3 PURPLE flashes (500ms ON; 200ms OFF): the key of the configuration tag does match to the reader key.

•5 RED flashes (500ms ON; 200ms OFF): the model of the reader of the configuration tag does match to the model of the reader.

The end of the start sequence is indicated by the flashing of the reader LEDs (red and green) 3 times (500ms ON; 500ms OFF).

LED indication - SMA / SLA

Power supply OK: fixed red LED

Power supply too low: blinking red LED (500ms ON / 500 ms OFF)

Temperature error: blinking red LED 5 times after all reading sequence. (RF Scan)

RF error, antenna problem: blinking red LED 3 times after all reading sequence. (RF Scan)

Communication: Green LED

Dimensions (mm/in) - SMA

Mounting - SMA

Mount with a 75 x 75 mm / 0.79 x 0.79 in VESA standard

mounting bracket M4x12 stainless steel screws provided

with mounting kit)

Two mounting possibilities:

Adjustable wall-mounted kit

(refer to the Installation Procedures

for KFX-UHF-08)

Adjustable pole-mounted kit

(refer to the Installation Procedures

for KFX-UHF-09)

Or mount directly on a wall

Ø4x35 aluminum screws provided (TCL ALU 4x12).

SPECTRE Access UHF

Read only & osdp

Installation procedure

UHF SPECTRE Access

Lecture seule & osdp

Notice d’installation

UHF SPECTRE Access

Solo lectura & osdp

Manual de instalación

Wall

Pole

Antenna Connection - SMA

An antenna must be connected to the RF port 1 (closed to the LEDs).

Mounting an Antenna on Module - SLA

- Attach the antenna on the module with the 4 screws (TCL ALU M4x12)

provided

with the module.

- Remove the cap from port RF 1.

- Connect the antenna to port RF 1 of the module.

Reader Dimensions (mm / in) - SLA

Mounting - SLA

Mount with 75 x 75 mm / 0.79 x 0.79 in Standard VESA

mounting bracket M4x12 polier screws provided with

mounting kit)

Two mounting possibilities:

Adjustable wall-mounted kit

(refer to the Installation Procedures

for KFX-UHF-08)

Adjustable pole-mounted kit

(refer to the Installation Procedures

for KFX-UHF-09)

RF Port 1

Antenna must be

connected to RF Port 1

4 serializable cable lengths are available:

1.5 m /4.92 ft: CAB-SPECTRE-1.5M

3 m / 9.84 ft: CAB-SPECTRE-3M

9 m / 29.53 ft: CAB-SPECTRE-9M

12 m / 39.37 ft: CAB-SPECTRE-12M

Only possible combinations:

CAB-SPECTRE-1.5M + CAB-SPECTRE-1.5M

CAB-SPECTRE-1.5M + CAB-SPECTRE-3M

CAB-SPECTRE-1.5M + CAB-SPECTRE-9M

CAB-SPECTRE-3M + CAB-SPECTRE-3M

SPECTRE Access UHF

Read only & osdp

Installation procedure

UHF SPECTRE Access

Lecture seule & osdp

Notice d’installation

UHF SPECTRE Access

Solo lectura & osdp

Manual de instalación

To antenna

To module

Label

Wall

Pole

Antenna Connection - SLA

Antenna Cables SMA / SLA

The antenna cables have a male connector and a female connector.

Antenna Specifications - ANT-UHF-V2

Antenna Mounting

Mount with 75 x 75 mm / 0.79 x 0.79 in Standard VESA

mounting bracket (M4x12 stainless steel screws provided

with mounting kit)

Two mounting possibilities:

Adjustable wall-mounted kit

(refer to the Installation Procedures

for KFX-UHF-08)

Adjustable ole-mounted kit

(refer to the Installation Procedures

for KFX-UHF-09)

ANT-UHF2-A

for SMA/SLA-x4x

ANT-UHF2-B

for SMA/SLA-x5x

Frequency Band

865 - 868 MHz

902 - 928 MHz

Antenna gain

8.30 dBi

9.68 dBi

Polarization

Circular

Axial ratio

0.66

1.16

Beamwidth (-3 dB)

70°

60°

Impedance

50 ohms

Cable

TNC RP male

Protection

Level IP66

4 serializable cable lengths are available:

1.5 m /4.92 ft: CAB-SPECTRE-1.5M

3 m / 9.84 ft: CAB-SPECTRE-3M

9 m / 29.53 ft: CAB-SPECTRE-9M

12 m / 39.37 ft: CAB-SPECTRE-12M

Only possible combinations:

CAB-SPECTRE-1.5M + CAB-SPECTRE-1.5M

CAB-SPECTRE-1.5M + CAB-SPECTRE-3M

CAB-SPECTRE-1.5M + CAB-SPECTRE-9M

CAB-SPECTRE-3M + CAB-SPECTRE-3M

348.7 / 13.73

279.2 / 10.99

45.1 / 1.78

SPECTRE Access UHF

Read only & osdp

Installation procedure

UHF SPECTRE Access

Lecture seule & osdp

Notice d’installation

UHF SPECTRE Access

Solo lectura & osdp

Manual de instalación

Azimuth pattern

Horizontal polarization F = 867 MHz

Horizontal polarization F = 915 MHz

Vertical polarization F = 867 MHz

Vertical polarization F = 915 MHz

Declaration of Compliance

STid declares that the SMA-R5x/R4x-A reader is compliant to the fundamental requirements of Directive RED 2014/53/EU and Directive RoHs 2011/65/EU and Commission Delegated

Directive 2015/863/EU. A copy of our declaration is available upon request send to qualit[email protected].

This device complies with Part 15 of the FCC rules and with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two

conditions: 1) This device must not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to

operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates, uses and can emit radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the distance between the equipment and receiver.

-Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for assistance.

This equipment complies with FCC’s and ISEDC's radiation exposure limits (using RSS-102 rules) set forth for an uncontrolled environment under the following conditions:

- This equipment should be installed and operated such that a minimum separation distance of 34 cm / 13.39 in is maintained between the radiator (antenna) and the

user’s/nearby person’s body at all times.

- The transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.

SPECTRE Access UHF

Read only & osdp

Installation procedure

UHF SPECTRE Access

Lecture seule & osdp

Notice d’installation

UHF SPECTRE Access

Solo lectura & osdp

Manual de instalación

Module Access SPECTRE - SMA

Lecteur SPECTRE - SLA

Bande de fréquence

Références

Bande de fréquence

Références

865 - 868 MHz

SMA-R41-A-U04-xx: TTL

SMA-R42-A-U04-5AB: RS232

SMA-R43-A-U04-7AB: RS485

SMA-W43-A-U04-7OS: osdp

865 - 868 MHz

ERP: 2W

SLA-R41-A-U04-xx: TTL

SLA-R42-A-U04-5AB: RS232

SLA-R43-A-U04-7AB: RS485

SLA-W43-A-U04-7OS: osdp

902 - 928 MHz

SMA-R51-A-U04-xx: TTL

SMA-R52-A-U04-5AB: RS232

SMA-R53-A-U04-7AB: RS485

SMA-W53-A-U04-7OS: osdp

902 - 928 MHz

EIRP: 4W

SLA-R51-A-U04-xx: TTL

SLA-R52-A-U04-5AB: RS232

SLA-R53-A-U04-7AB: RS485

SLA-W53-A-U04-7OS: osdp

Maroc

867.7-867.9 MHz

SMA-R41-A-U04-xx1M: TTL

SMA-R42-A-U04-5AB1M: RS232

SMA-R43-A-U04-7AB1M: RS485

SMA-W43-A-U04-7OS1M: osdp

Maroc

867.7-867.9 MHz

ERP: 0.5W

SLA-R41-A-U04-xxM: TTL

SLA-R42-A-U04-5ABM: RS232

SLA-R43-A-U04-7ABM: RS485

SLA-W53-A-U04-7OSM: osdp

Pérou

916-928 MHz

SMA-R51-A-U04-xx1PE: TTL

SMA-R52-A-U04-5AB1PE: RS232

SMA-R53-A-U04-7AB1PE: RS485

SMA-W53-A-U04-7OS1PE: osdp

Pérou

916 - 928 MHz

EIRP: 4W

SLA-R51-A-U04-xx1PE: TTL

SLA-R52-A-U04-5AB1PE: RS232

SLA-R53-A-U04-7AB1PE: RS485

SLA-W53-A-U04-7OS1PE: osdp

Caractéristiques de l’alimentation - SMA / SLA

Utiliser une alimentation AC/DC du type LPS, Source à Puissance Limitée (selon IEC EN 60950-1 Ed2) ou de type ES1, PS1 (selon IEC EN 62368-1) pour

l’alimentation principale et pour un éventuel V+/V-.

Alimentation principale : Gamme +9 Vdc à +36 Vdc Typique : +12 Vdc

Consommation : Typique : 1A sous +12 Vdc Max : 1.5A sous +12 Vdc

Caractéristiques - SMA / SLA

Communication : RS485 (L+ & L-) / RS232 (TD & RD) / TTL (Wiegand / Clock & Data)

Raccordement : Borniers débrochables à vis 3x4 points et 1x8 points, Pas de 3,81 mm

T° de fonctionnement : -25 °C / +60°C

Indice de protection : Niveau IP66

Puce lue : EPC1 Gen2 (ISO 18000-63) - 1 à 62 octets max

I/O : 4 entrées et 4 sorties opto-couplées

LEDs sur module : 1 LED rouge : présence tension d’alimentation // 1 LED verte : activité sur la liaison Lecteur / Host

LEDs sur antenne : 7 couleurs configurables (rouge, vert, bleu, orange, violet, turquoise, blanc)

Type de câble préconisé - SMA / SLA

RS485 : Utiliser du câble multiconducteur torsadé blindé par tresse, reliée à la masse du concentrateur. Déport max :1000 m. à 9600 bauds

RS232 : Déport max 15 m.

Wiegand / Clock & Data : Utiliser du câble multiconducteur blindé non torsadé

2 fils 6/10° - 30 m max

4 fils 6/10° - 60 m max

6 fils 6/10° - 100 m max

2 fils 9/10° - 50 m max

4 fils 9/10° - 100 m max

Recommendations - SMA / SLA

▪Installer le module à distance des câbles de transmission informatique ou d’origine de puissance (ex : RJ45, secteur...).

Les perturbations qu’ils peuvent engendrer peuvent varier en fonction de leur puissance de rayonnement et de leur proximité.

▪Utiliser une alimentation filtrée et régulée.

▪Des antennes connectées à des lecteurs différents peuvent se perturber. Eloigner les, les unes des autres.

Il est recommandé d’utiliser une alimentation 1,5 A minimum sous +12Vdc.

Si les IN/OUT sont alimentés par le module utiliser une alimentation de 2A min sous +12Vdc.

▪Un utilisateur ne doit pas se trouver de manière prolongée, à une distance inférieure à 34 cm d’une antenne conformément aux préconisations de la

norme EN50364 applicable à ce type d’appareil.

▪Il est proscrit d’ouvrir le boîtier module mis à part la trappe.

▪Avant toute opération de service, vous devez mettre le lecteur hors tension.

▪S’assurer que le joint de trappe est bien positionné avant fermeture.

▪Ne pas retirer les bouchons des presse-

étoupes non-utilisés :

▪Ne pas retirer les capuchons des

connecteurs RF non-utilisés :

▪Installer le module en respectant la signalétique UP

vers le haut afin que les connectiques soient vers le bas : :

Accès à la connectique - SMA / SLA

Afin d’accéder à la connectique du lecteur, ouvrir uniquement la trappe prévue à cet effet en dévissant les 4 vis imperdables sans les ôter de la trappe.

SPECTRE Access UHF

Read only & osdp

Installation procedure

UHF SPECTRE Access

Lecture seule & osdp

Notice d’installation

UHF SPECTRE Access

Solo lectura & osdp

Manual de instalación

Vue de face du module - SMA / SLA

Connexion TTL / RS232 / RS485 / I/O - SMA / SLA

Configuration - SMA / SLA

Le nombre d’antenne, le nombre de voie, le protocole de communication sont configurables via l’application Ultrys V2 ou lors de la commande du module.

▪Protocoles TTL (Wiegand & ISO2) :

- ISO2 (Clock & Data) –Décimal (7 octets max).

- Wiegand 26 bits

- Wiegand avec LRC –Hexadécimal (12 octets max) + LRC.

- Wiegand sans LRC –Hexadécimal (12 octets max)……

▪Protocoles série (RS232 & RS485) : Il est possible de configurer la structure de la trame avec les paramètres optionnels suivants (grisés).

1 octet

1 octet + X octets

1 octet

STX

Numéro de Voie + Tag Data*

LRC

ETX

0x02

0x0y nn…..nn

0x0D

0x0A

0x03

- STX+ETX : ajout d’un 0x02 (STX) et 0x03 (ETX) en début et fin de trame - CR/LF : retour chariot (0x0D + 0x0A) configurable séparément

- LRC : octet de contrôle (XOR de tous les octets précédents hormis STX) - Données transmises en décimal ou hexadécimal

- ASCII : si cette option est activée, les données incluses dans la trame seront au format ASCII (la taille des données du tag lu sera alors doublée). -

Zéros non-significatifs : complète les données du tag avec des 0 non significatifs pour obtenir la taille de données définie.

(Voie n° + Zéro de bourrage + Données du tag...).

▪osdp protocole (RS485 7OS) : se reporter à la Spec_Protocole_7OS_OSDP_UHF-US.pdf

Presse étoupes (Bus Données- Alimentation-entrées/sorties)

Résistance de fin de lignes RS485

A utiliser, lors d’une communication RS485, lorsque la distance de câble de données approche ou est

supérieure à 100 m et que la communication se dégrade (signaux non francs, erreurs de trames etc.)

Niveau sortie TTL : +5V ou Vin

Connecteur micro USB pour configuration uniquement

J14

Utiliser ce connecteur pour la connexion à la terre

IN 1-2-3-4

4 Entrées opto-couplées

OUT 1-2-3-4

4 Sorties opto-couplées

V- opt

Potentiel de polarisation bas des entrées et sorties opto-couplées

V+ opt

Potentiel de polarisation haut des entrées et sorties opto-couplées

DATA1

Data ou D0 de la voie 1 ou Tx (RS232) ou L+ (RS485)

CLK1

Clock ou D1 de la voie 1 ou Rx (RS232) ou L-(RS485)

DATA 2 / CLK2

Data/Clock ou D0/D1 de la voie 2

DATA 3 / CLK3

Data/Clock ou D0/D1 de la voie 3

DATA 4 / CLK4

Data/Clock ou D0/D1 de la voie 4

ALIM

Alimentation

GND

LED rouge

LED verte

Port RF1

Port RF2

Port RF3

Port RF4

SPECTRE Access UHF

Read only & osdp

Installation procedure

UHF SPECTRE Access

Lecture seule & osdp

Notice d’installation

UHF SPECTRE Access

Solo lectura & osdp

Manual de instalación

Mur

Mât

Séquence de démarrage - SMA / SLA

A la mise sous tension : la LED lecteur rouge s’allume. Initialisation du lecteur.

Après l’initialisation, le lecteur recherche un tag de configuration pendant environ 15s sur l’antenne 1 (connectée au port RF 1).

•Si pas de tag détecté : clignotement de la LED antenne « couleur RFON » (200 ms) (par défaut bleu) / RFOFF (200ms).

•Si détection d’un tag quelconque : la LED antenne enchaîne la séquence « couleur RFON « (par défaut bleu) / « couleur DETECTION » (par défaut orange)

pendant 200ms puis LED OFF.

•Si détection d’un tag de configuration : la LED antenne enchaîne laséquence « couleur RFON « (par défaut bleu) / « couleur DETECTION » (par défaut orange)

pendant 200ms puis LED OFF puis la LED antenne donne les indications suivantes :

•3 clignotements de couleur VERT (500ms ON ; 200ms OFF) : prise en compte du tag de configuration OK.

•3 clignotements de couleur ROUGE (500ms ON ; 200ms OFF) : la régulation (région) du tag de configuration ne correspond pas à la régulation du lecteur.

•3 clignotements de couleur VIOLET (500ms ON ; 200ms OFF) : la clé du tag de configuration ne correspond pas à la clé du lecteur.

•5 clignotements de couleur ROUGE (500ms ON ; 200ms OFF) : le modèle de lecteur du tag de configuration ne correspond pas au modèle du lecteur.

La fin de la séquence de démarrage est indiquée par le clignotement des LEDs lecteur (rouge et verte) 3 fois (500ms ON ; 500ms OFF).

Indication LED module - SMA / SLA

Alimentation OK : LED fixe rouge.

Alimentation trop faible : clignotement LED rouge (500ms ON / 500 ms OFF)

Problème de Température : clignotement LED rouge 5 fois après chaque séquence de lecture. (RF Scan)

Problème RF: clignotement LED rouge 3 fois après chaque séquence de lecture (RF Scan).

Communication: LED verte.

Dimensions (mm) - SMA

Fixation - SMA

1- Fixation avec un support de fixation de type VESA

2- standard 75x75 mm (vis M4x12 Inox fournies dans

3- le kit de fixation)

Deux modes de fixation possibles :

Kit de fixation murale orientable

(se référer à la Notice d’installation

du KFX-UHF-08)

Kit de fixation mât orientable

(se référer à la Notice d’installation

du KFX-UHF-09)

Ou Fixation directement sur un mur

Vis Ø4x35 inoxydable recommandée.

Altri manuali per Spectre

Indice

Lingue:

Altri manuali Stid Sistema microfonico

Stid

Stid SPECTRE NANO Manuale operativo e di manutenzione

Manuali Sistema microfonico popolari di altre marche

Paso

Paso R824 Manuale utente

Naxa

Naxa NAM-982 Manuale utente

Motorola

Motorola PMNN4461 Manuale utente

Xvive

Xvive U3 Manuale utente

Tekon

Tekon DUOS Manuale utente

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuale utente

Devine

Devine WMD-IE Manuale utente

LG LF-D7150 Manuale utente

GE S768DAV Manuale utente

LD U305 HBH 2 Manuale utente

Chainway

Chainway URA8 Manuale utente

ORATOR

ORATOR D860TD Manuale utente

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente

Alpha Technologies

Alpha Technologies RBMS Manuale utente

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuale utente

Shure

Shure UA844 Manuale utente

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente

Pyle

Pyle PDWM5000 Manuale utente