Stinger ELEV8 UN1880 Manuale utente

8" FLOATING MULTIMEDIA DISPLAY SYSTEM

MODEL NUMBER: UN1880

INSTALLATION GUIDE

StingerElectronics.com

Installation of this product requires technical skill

and experience. It is recommended to have it

professionally installed by a Stinger / Phoenix Gold

Dealer.

Read entire instructions thoroughly before starting.

Disconnect the vehicle's negative battery cable

before making any wire connections.

Protect all vehicle surfaces with tape or plastic

Do not install components in any location that will

hinder vehicle operation, such as steering wheel,

gearshift, air bags, hazard switch.

All wiring should be secured away from sharp

edges and moving parts.

CONTENTS

Precautions......................................................2

Parts List........................................................3

Mounting Options..........................................4

Double DIN Dash Kit Mounting.......................5

Double DIN Factory Bracket Mounting..............6

Single DIN Dash Kit Mounting..........................7

Final Assembly.................................................8

Wiring & Connections......................................9

PRECAUTIONS

AGREEMENT: End user agrees to use this product in

compliance with the instructions and terms of use and

with all State and Federal laws. STINGER provides

instructions and safety warnings with respect to this

product and disclaims all liability for any use not in

conjunction with those instructions or other misuse of

its product. If you do not agree, please discontinue use

and contact STINGER. This product is intended for off-

road use and passenger use only.

TECHNICAL SUPPORT:

800-477-2267

[email protected]

CUSTOMER SOLUTIONS:

800-477-2267

[email protected]

MODEL NUMBER: UN1880

Stinger is a Power Brand of AAMP Global

15500 Lightwave Drive, Suite 202

Clearwater, Florida 33760

INSTALLATION GUIDE

Visit StingerElectronics.com

for updates and further detailed information.

PARTS LIST

OPTIONAL ACCESSORIES (SOLD SEPARATELY)

QTY DESCRIPTION PART NO

1 Touch Panel Display UN1880-D

1 Radio Module UN1880-M

Mounting Brackets / Hardware

1 Plastic Dash Mounting Bracket

SE-1000

1 Display Mounting Clamp

1 Metal Mounting Bracket

1 Horizontal Display Angle Plate

1 Rubber Boot SE-1001

4 M4 X 6 Screw

SE-1002

4 M4 X 10 Screw

4 M4 X 12 Screw

2 M4 X 14 Screw

2 M4 x 18 Screw

6 M5 x 10 Screw

6 #10 x 3/8 Screw

2 Backstrap SE-1003

Cables / Harnesses

1 8 Pin Display Power Harness SE-1100

1 LVDS Display Video Cable SE-1101

1 16 Pin Power / Speaker Harness SE-1102

1 24 Pin AV / Rear Camera Harness SE-1103

1 10 Pin Multi Camera Harness SE-1104

1 6 Pin SWI / IR Harness SE-1105

1 4 Pin Mic / Camera Audio Harness SE-1106

1 SiriusXM Cable SE-1107

1 External Microphone SE-1108

1 GPS Antenna & Mounting Plate SE-1109

DESCRIPTION PART NO

IR Remote Control SE-1500

8 Pin Display Power Harness - 5FT SE-1501

LVDS Display Video Harness - 5FT SE-1502

PAC Dash Mount HDMI & USB Extension - 3FT HDMI-USB-CBL

PAC Dash Mount USB Adaptor - 3FT/6FT USDMA3 / USBDMA6

iGO North American Map (Micro SD Card) SE-P14

Double DIN: Attach the Metal Bracket to

the Plastic Dash Mounting Bracket using M4

X 6 screws. Attach metal bracket and plastic

dash mounting bracket assembly to the Radio

Module using M4 X 6 screws.

The display can be installed Flat or Angled towards the driver. For flat mounting, attach the

clamp assembly (6) to the display using M4 X 14 screws (FIG. A). If a horizontal angle is

desired, insert the angle plate (7) in between the clamp and display and replace 2 of the

M4 X 14 screws with M4 X 18 screws on the thicker side of the angle plate (FIG. B). Center

the bracket on the back of the display as a starting point, and if needed you can adjust up

or down.

MULTIPLE MOUNTING OPTIONS...

ELEV8 can be configured for different mounting applications:

• Using a Double DIN Dash Kit (3A)

• Using Double DIN Factory Radio Mounting Brackets (3B)

• Using a Single DIN Dash Kit (3C)

• Custom Mounting Applications

M4 X 18

(2X)

M4 X 14

(2X)

M4 X 14

(4X)

FIG. A FIG. B

M4 X 6

TOP

Single DIN: For Single DIN installations,

you will be mounting the Plastic Dash

Mounting Bracket in the dash kit and the

Radio Module will be mounted remotely.

Before beginning the installation,

determine where the Radio Module will

be installed and make sure the Display

Cables are long enough. Longer, 5 foot

cables are available (SE-1501 & SE1502).

Metal

Bracket

Radio

Module

Plastic Dash

Mounting Bracket

Optional

Cable Channel

M4 X 12

(4X)

M4 X 6 M4 X 10 M4 X 12 M4 X 14 M4 X 18

#10 X 3/8 M5 X 10

NOTE: Depending on the

installation, not all screws

will be used.

DOUBLE DIN DASH KIT MOUNTING

3A Display Adjustment & Mounting:

Making sure to use all 8 screws, loosely

attach the radio module and mounting

bracket assembly to the side brackets of the

aftermarket dash mounting kit using #10

X 3/8 screws for the bottom locations and

the M5 X 10 screws for the top locations

(radio chassis), do not tighten. (FIG. A)

Temporarily attach the display to the

bracket assembly. (FIG. B)

Using the main frame of the dash kit as

a guide, slide radio assembly forward

or backward to desired position. Tilt the

display vertically and determine if the

display should be flat or tilted up. If display

needs to move up or down, refer to Step 2.

Once in the desired position, tighten screws

to the radio chassis (top) and mounting

bracket assembly (bottom). See Step 4 for

vertical position.

Remove the display from the bracket

assembly by lifting upward and unhooking.

Note: There are multiple mounting holes

on the mounting bracket to allow adjusting

the mounting depth. You may drill

additional holes in the mounting bracket

and/or the dash kit brackets to align the

display in the best position and ensure you

can use all 8 mounting screws.

Note: If you encounter a depth issue with

the radio module in the top position, you

may move it to the bottom location by

inverting the mounting bracket assembly.

(FIG. C)

Note: If the installation requires the display

to be installed last, do not push the display

all the way up against the dash kit. Leave

enough bottom gap as the display's bottom

edge rotates towards the dash kit.

HOOK BOTTOM

FIRST, THEN TOP

#10 X 3/8

Coarse Thread Screw

M5 X 10

AFTERMARKET

DASH KIT

(NOT INCLUDED)

NOTE: BOOT AND DASH KIT (NOT SHOWN)

FIG. C

FIG. B

FIG. A

PROCEED TO STEP 4

DOUBLE DIN FACTORY BRACKET MOUNTING

3B Display Adjustment & Mounting:

Making sure to use all 8 screws, loosely

attach the radio module and mounting

bracket assembly to the factory brackets

using #10 X 3/8 screws for the bottom

locations and the M5 X 10 screws for

the top locations (radio chassis), do not

tighten. (FIG. A)

Temporarily attach the display to the

bracket assembly. (FIG. B)

Using the dash panel as a guide,

determine the desired position and if

necessary create new mounting locations

in the factory brackets. Tilt the display

vertically and determine if the display

should be flat or tilted up. If display needs

to move up or down,refer to

Step 2.

Once in the desired position, tighten screws

to the radio chassis (top) and mounting

bracket assembly (bottom).

See Step 4 for vertical position.

Remove the display from the bracket

assembly by lifting upward and unhooking.

Note: It may be necessary to create new

mounting locations in the factory brackets.

Note: If you encounter a depth issue with

the radio module in the top position, you

may move it to the bottom location by

inverting the mounting bracket assembly.

(FIG. C)

Note: If the installation requires the display

to be installed last, do not push the display

all the way up against the dash. Leave

enough bottom gap as the display's bottom

edge rotates towards the dash.

HOOK BOTTOM

FIRST, THEN TOP

Factory Bracket

M5 X 10

NOTE: BOOT AND DASH KIT (NOT SHOWN)

FIG. B

FIG. C

FIG. A

PROCEED TO STEP 4

#10 X 3/8

Coarse Thread Screw

SINGLE DIN DASH KIT MOUNTING

M5 X 10

3C Display Adjustment & Mounting:

Making sure to use all 4 screws, loosely

attach the plastic mounting bracket

assembly to the side brackets of the

aftermarket dash mounting kit using

#10 X 3/8 screws, do not tighten.

(FIG. A)

Temporarily attach the display to the

bracket assembly. (FIG. B)

Using the main frame of the dash kit as

a guide, slide radio assembly forward

or backward to desired position. Tilt

the display vertically and determine if

the display should be flat or tilted up. If

display needs to move up or down,

refer to Step 2.

Once in the desired position, tighten

screws to the plastic mounting bracket

assembly. See Step 4 for vertical position.

Remove the display from the bracket

assembly by lifting upward and

unhooking.

Note: There are multiple mounting

holes on the mounting bracket to allow

adjusting the mounting depth. You may

drill additional holes in the mounting

bracket and/or the dash kit brackets to

alight the display in the best position.

Note: To align the display in the best

position, you may invert the plastic

mounting bracket assembly. (FIG. C)

Note: Note: If the installation requires

the display to be installed last, do not

push the display all the way up against

the dash kit. Leave enough bottom gap

as the display's bottom edge rotates

towards the dash kit.

HOOK BOTTOM

FIRST, THEN TOP

AFTERMARKET

DASH KIT

(NOT INCLUDED)

NOTE: BOOT AND DASH KIT (NOT SHOWN)

FIG. B

FIG. C

FIG. A

PROCEED TO STEP 4

#10 X 3/8

Coarse Thread Screw

Insert a M5 X 10 on each side of the clamp

assembly. Use Hole A for no vertical tilt

or Hole B for 8 degrees of vertical tilt as

determined in Step 3.

If needed, attach the rubber boot to

the display clamp assembly by aligning

the notch on the top edge as shown,

and hook the boot to the clamp at 5

locations.

Note: The boot is not required if display

sits very close to the dash/dash kit and

no large gap is seen.

BOOT ASSEMBLY PLASTIC "TAB"

HAS TO GO INTO A NOTCH

(DISPLAY UNIT NOT SHOWN)

BOOT ASSEMBLY HOOKS

AT 5 SPOTS

(RUBBER BOOT NOT SHOWN)

BOOT ASSEMBLY PLASTIC "TAB"

HAS TO GO INTO A NOTCH

(DISPLAY UNIT NOT SHOWN)

BOOT ASSEMBLY HOOKS

AT 5 SPOTS

(RUBBER BOOT NOT SHOWN)

FINAL ASSEMBLY

After all wiring connections are made

in the next section, the dash kit with the

radio chassis and bracket assembly,

should be installed and any factory

panels reinstalled. Connect the 8 Pin

Display Power Harness and the LVDS

Video Cable to the back of the display

and attach display to mounting bracket.

M5 X 10

Connect radio power and

speaker connections to a vehicle

specific harness (sold separately)

referencing diagram at right.

WIRING & CONNECTIONS

16 Pin Power / Speaker Harness

Display Cable

Multi Camera

USB1 CP/AA1

Power / Speaker

GPS Antenna2 LVDS Cable

HDMI Input

USB2

SWI

AV In/Out - Rear Camera Microphone SiriusXM Tuner

Radio Antenna

TOSLINK

Green/Black Rear Left Speaker -

Green Rear Left Speaker +

Purple/Black Rear Right Speaker -

Purple Rear Right Speaker +

White/Black Front Left Speaker -

White Front Left Speaker +

Grey/Black Front Right Speaker -

Grey Front Right Speaker +

Green/White Reverse Trigger +

Pink Parking Brake -

Orange Illumination3+

Yellow Battery 12V +

Blue Power Antenna +

Blue/White Amp Remote +

Red Accessory 12V +

Black Ground -

3Illumination wire must be connected for

Day/Night and Auto Dimming to work.

2GPS Antenna must be installed for accurate

operation of CarPlay, Android Auto & internal

Navigation.

1The top USB1 must be used for CarPlay

and Android Auto.

15 Amp Fuse

A1 Brown / Black SWC Key 2

A2 Brown SWC Key 1

A3 Black SWC Ground

A4 Yellow RCA Video Input

A5 White RCA Audio Input Left

A6 Red RCA Audio Input Right

A7 Yellow RCA Camera Input

A8 Yellow RCA Video Output 1

A9 Yellow RCA Video Output 2

A10 White RCA Zone 2 Left

A11 Red RCA Zone 2 Right

A12 Red RCA Right front

A13 White RCA Left Front

A14 Red RCA Right Rear

A15 White RCA Left Rear

A16 Brown RCA Left Subwoofer

A17 Blue RCA Right Subwoofer

Analog Steering

Wheel Control Input

Audio / Video Input

Video Output

Audio Output

24 Pin AV / Rear Camera Harness

Audio/Video Inputs & Outputs / Rear Camera Video Input / Resistive Steering Wheel

Control Inputs - To program SWC, go to SETTINGS, then select the Gear Icon,

Passcode: 15500 > OK > SWC CUSTOM. Do not use if using a PAC SWI Interface.

SiriusXM®Harness

For connecting optional SiriusXM

SXV 300 satellite radio tuner.

WIRING & CONNECTIONS

Altri manuali per ELEV8 UN1880

Indice

Altri manuali Stinger Sistema video per auto

Stinger

Stinger HEIGH10 RB10RAM13B Manuale utente

Stinger

Stinger HEIGH10 UN1810E-FT3 Manuale utente

Stinger

Stinger HEIGH10 SRK-JK11H Manuale utente

Stinger

Stinger HEIGH10 UN1810E-AU1 Manuale utente

Stinger

Stinger ELEV8 UN1880 Manuale utente

Stinger

Stinger VIP Manuale utente

Stinger

Stinger HEIGH10 UN1810E-VW3 Manuale utente

Stinger

Stinger SPXRNGDASH Manuale utente

Stinger

Stinger VIP Manuale utente

Stinger

Stinger ELEV8 UN1880 Manuale utente

Stinger

Stinger Heigh10 Manuale utente

Stinger

Stinger HEIGH10 UN1810E-FT2 Manuale utente

Stinger

Stinger HEIGH10 SRK-JW18EH Manuale utente

Stinger

Stinger HEIGH10 RB10RAM13B Manuale utente

Stinger

Stinger Heigh10 Manuale utente

Stinger

Stinger Heigh10 Manuale utente

Stinger

Stinger STH10TACOM Manuale utente

Stinger

Stinger Heigh10 Manuale utente

Stinger

Stinger HEIGH10 UN1810E-FD5 Manuale utente

Stinger

Stinger HEIGH10 SRK-RAM13H Manuale utente

Stinger

Stinger HEIGH10 SRK-RAM13H Manuale utente

Stinger

Stinger HEIGH 10 Manuale utente

Stinger

Stinger Heigh10 Manuale utente

Manuali Sistema video per auto popolari di altre marche

Eonon

Eonon E1057 Manuale utente

Milion

Milion D2223 Manuale utente

Metra Electronics

Metra Electronics 99-8153 Manuale utente

Voxx Electronics

Voxx Electronics HR8MA1 Manuale utente

Axxera

Axxera AV604Bi Manuale utente

Clarion

Clarion NX706E Manuale utente

Pyle view

Pyle view PLDN74BTi Manuale utente

Clarion

Clarion NX602 Manuale utente

PowerAcoustik

PowerAcoustik PTID-5850N Manuale utente

RCA

RCA DRC6296 - Twin 9" Mobile DVD System Guida utente

Lanzar

Lanzar SVDVD5 Manuale utente

Kia

Kia MTXM100YPPE Manuale utente

Eonon

Eonon E1060 Manuale utente

Macrom

Macrom M-AN900 Manuale utente

Hyundai

Hyundai BAPE-L3000N Manuale utente

r.LiNK

r.LiNK RL2-UCON8-SM Manuale utente

Blaupunkt

Blaupunkt DVP 01C Manuale utente

DP Audio Video

DP Audio Video dbd807nav Manuale utente