Stout Designs TRAILBLAZER Manuale utente

2020

TRAILBLAZER - Operation Manual

Stout Designs, LLC

1/1/2020

TRAILBLAZER –OWNER’S MANUAL

Operating tips: VERY IMPORTANT

• Always run TRAILBLAZER at full throttle when cutting.

• Make sure the kill switch somewhere close to you so you can shut the machine down in the event you need to. (i.e. if you

get the saw in a bind or your around bystanders.)

• If you get the saw in bind and the belts slip or start stalling the motor, the first reaction you should have is to reverse

backwards or use the kill switch.

• Always walk away from the blade side while the blades are running.

• Don't let debris build up to heavy on top of the motor as the debris could get hot and ignite if left on top of the engine.

• Try to always use 91 or better non-ethanol fuel.

• Always tighten your blades with an impact wrench. A hand wrench will not tighten them enough.

• Never tighten the set screw on the clutch assembly jaw coupling (this coupling is designed to slip if needed). All other

setscrews on the bearings, drive shaft jaw coupling and clutch housing can be tightened and should be checked prior to use.

picture of setscrew to never tighten to follow.

• Visually Check to make sure Blue Spider is locked in place as shown in picture to follow

Note: if used on public trails, roads or pathways, please always use with caution and always use a lead and

trail vehicle to alert any potential oncoming public vehicles that trail maintenance equipment is near.

BLUE SPIDER PROPERLY ENGAGED.

TURN STAINLESS STEEL RING TO

THIS POSITION IF FOR SOME REASON

IT IS NOT.

TRAILBLAZER

US PAT. D795,307

US PAT. 9,807,928

VERTICAL TRAIL TRIMMER

OPERATOR / SAFETY MANUAL

!WARNING!

Note the following before starting:

Please read the operator's manual carefully.

INTRODUCTION

Dear Customer,

Congratulations on your choice to buy a Stout Designs, LLC product!

Today Stout Designs, LLC is striving to be one of the leading manufacturers in the world of

forest coppicing products for use on ATV’s, UTV’s, Golf Carts and small tractors, with quality

as our highest priority. The business concept is to develop, manufacture and market motor-driven

products for forestry and trail management. Stout Designs’ aim is to develop equipment that

insures ergonomics, usability and environmental protection.

We are confident that you will appreciate, with great satisfaction, the quality and performance of

our product for a very long time to come. The purchase of one of our products gives you access

to one of the most innovative products in trail/pathway clearing and limb/brush management

along with professional help with repairs and service if it ever becomes necessary. If the retailer

who sells your machine is not Stout Designs, LLC or one of our authorized dealers, ask for the

address of your nearest service dealer or the product can be returned to Stout Designs, LLC for

any repair needs.

It is our wish that you will be satisfied with your product and that it will be your companion for a

long time. Think of this operator′s manual as a valuable document. By following its content

(usage, service, maintenance, etc.), the life span and the second-hand value of the machine can

be extended. If you sell this machine, make sure that the operator′s manual is passed on to the

buyer.

Thank you for using a Stout Designs, LLC product.

Stout Designs, LLC has a policy of continuous product development and therefore reserves the

right to modify the design and appearance of products without prior notice.

! WARNING !

The machine is designed for trimming horizontally orientated overhanging branches 2” in

diameter or less along forestry trails, pathways and roads and is to be used only when area is

clear of bystanders, fellow workers or animals.

The only accessories you can operate with this equipment are ones provided by Stout Designs,

LLC and specifically designed for your exact unit.

Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication

that could affect your vision, your judgement or your co-ordination.

Shut down equipment engine prior to exiting the vehicle and visually ensure the blades have

stopped completely.

Ideal operating speed for the saw is 3200-3600 RPM. Although the saw will run at a higher

RPM the motor is designed to operate at a maximum RPM of 3600 and actually produces the

most torque between 3200-3600 RPM. Blades will begin to rotate at an RPM greater than 2000

RPM.

Wear personal protective equipment. See instructions under the “Personal protective equipment”

heading.

Never use a machine that has been modified in any way from its original specification.

Never use a machine that is faulty. Carry out the checks, maintenance and service instructions

described in this manual. Some maintenance and service measures must be carried out by trained

and qualified specialists. See instructions under the Maintenance heading.

All covers, guards and handles must be fitted before starting. Ensure that the spark plug cap and

ignition lead are undamaged to avoid the risk of electric shock.

The machine operator must ensure that no people or animals come closer than 20 feet while

working. When several operators are working in the same area the safety distance should be at

least 50 feet.

Carry out an overall inspection of the machine before use. See the maintenance schedule. In

addition to this manual, a Service manual from the MOTOR manufacturer will be provided.

! WARNING !

Long-term exposure to noise can result in permanent hearing impairment. So always use

approved hearing protection.

! WARNING !

Under no circumstances may the design of the machine be modified without the permission

of the manufacturer. Always use original accessories. Non-authorized modifications and/or

accessories can result in serious personal injury or the death of the operator or others.

! WARNING !

A TRAILBLAZER can be dangerous if used incorrectly or carelessly, and can cause

serious or fatal injury to the operator or others. It is extremely important that you read

and understand the contents of this operator’s manual.

! WARNING !

Running an engine in a confined or badly ventilated area can result in death due to

asphyxiation or carbon monoxide poisoning.

! WARNING !

You must use approved personal protective equipment whenever you use the machine. Personal

protective equipment cannot eliminate the risk of injury but it will reduce the degree of injury if

an accident does happen. Ask your dealer for help in choosing the right equipment if questions

arise.

HEAD PROTECTION

Head protection should whenever you operate an ATV of any kind. Protecting yourself from

potential head injuries is a key element of safe equipment operation. A head injury can impair

you for life or it can be fatal. Wearing a safety helmet or hard hat is one of the easiest ways to

protect an your head from injury. Hard hats can protect yourself from impact and penetration

hazards as well as from electrical shock and burn hazards. For your protection, head protection

must be worn if the trees being cleared are taller than 2 m. Approved head protection must

comply with the ANSI Z89.1.

HEARING PROTECTION

Wear hearing protection that provides adequate noise reduction. Generally, the louder the noise,

the shorter the exposure time before hearing protection is required. For instance, you may be

exposed to a noise level of 90 dB for 8 hours per day (unless they experience a Standard

Threshold Shift) before hearing protection is required. On the other hand, if the noise level

reaches 115 dB hearing protection is required if the anticipated exposure exceeds 15 minutes.

For a more detailed discussion of the requirements for a comprehensive hearing conservation

program, see OSHA Publication 3074 (2002), “Hearing Conservation” or refer to the OSHA

standard at 29 CFR 1910.95, Occupational Noise Exposure, section (c).Approved devices should

have a NRR (Noise Reduction Rating) of 20db.

!WARNING!

Listen out for warning signals or shouts when you are wearing hearing protection. Always

remove your hearing protection as soon as the engine stops.

EYE & FACE PROTECTION

Always wear approved eye protection. Face protection should be worn whenever possible.

Protective eyeglasses have safety frames constructed of metal or plastic and impact-resistant

lenses. Side shields are available on some models. Face shields are transparent sheets of plastic

that extend from the eyebrows to below the chin and across the entire width of your head. Some

are polarized for glare protection. Face shields protect against nuisance dusts and potential

splashes or sprays of hazardous liquids but will not provide adequate protection against impact

hazards. Face shields used in combination with goggles or safety spectacles will provide

additional protection against impact hazards. Wearing face protection does not adequately

protect your eyes; you must also wear approved eye protection. Approved eye protection must

comply with the ANSI Z87.1.

GLOVES

Gloves should be worn when necessary, e.g. when fitting cutting attachments. If a hazard

assessment reveals that you face potential injury to hands and arms that cannot be eliminated

through engineering and work practice controls, you must ensure that you wear appropriate

protection. Potential hazards include skin absorption of harmful substances, chemical or thermal

burns, electrical dangers, bruises, abrasions, cuts, punctures, fractures and amputations.

Protective equipment includes gloves, finger guards and arm coverings or elbow-length gloves.

You should explore all possible engineering and work practice controls to eliminate hazards and

use PPE to provide additional protection against hazards that cannot be completely eliminated

through other means. For example, machine guards may eliminate a hazard. Installing a barrier

to prevent you from placing their hands at the point of contact between a table saw blade and the

item being cut is another method.

FOOT PROTECTION

Wear boots with steel toe-caps and non-slip sole. Safety footwear must meet ANSI minimum

compression and impact performance standards in ANSI Z41-1991 (American National Standard

for Personal Protection-Protective Footwear) or provide equivalent protection. Footwear

purchased before July 5, 1994, must meet or provide equivalent protection to the earlier ANSI

Standard (ANSI Z41.1-1967). All ANSI-approved footwear has a protective toe and offers

impact and compression protection. But the type and amount of protection is not always the

same. Different footwear protects in different ways. Check the product’s labeling or consult the

manufacturer to make sure the footwear will protect the user from the hazards they face.

Approved foot protection must comply with the ANSI Z41.1.

CLOTHING

Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and

branches. Always wear heavy, long pants. Do not wear jeweler, shorts, sandals or go barefoot.

Secure hair so it is above shoulder level.

FIRST AID KIT

Always have a first aid kit nearby.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Tagliabordi popolari di altre marche

MTD

MTD HT 51 E Manuale utente

McCulloch

McCulloch T22 LS Manuale utente

COCKRAFT

COCKRAFT PRO HL36-S Manuale utente

Grizzly

Grizzly CT 1800 Li Manuale utente

Peco

Peco Z Trimmer ZT-3000 Manuale utente

Solo

Solo 116 Manuale utente

Stiga

Stiga ST 1200 Manuale utente

Echo

Echo GT-225 - 10-09 Manuale utente

RedMax

RedMax BT17 Manuale utente

GreenWorks

GreenWorks STA806 Manuale utente

Parkside

Parkside PHSL 900 A3 Manuale utente

Gardeo

Gardeo PRO GPTHT2560 Manuale utente

Park

Park DT-810870 Manuale utente

Worx

Worx WG209 Manuale utente

Gardenline

Gardenline 43671/HTKS26 Manuale utente

Makita

Makita 3710 Manuale utente

Champion

Champion 100683 Manuale utente

Stihl

Stihl FS 311 Manuale utente