Stratco Handi-Mate 1 Manuale utente

SLIDING DOOR HANDI-MATE™ INSTALLATION GUIDE

HANDI-MATE™SHED

INSTALL GUIDE

PRIOR TO INSTALLATION

It is important that you contact your local government authority to determine if building approval is required.

To ensure that the installation and erection of your Stratco Handi-Mate™ Shed proceeds smoothly you should confirm that all the components and

materials listed on the delivery documentation and in this installation guide have been supplied. Details for ordering individual components can be found in

the “Component Index” section at the end of this document.

Carefully read this installation guide to familiarise yourself with all the steps involved and ensure that you have the correct tools and equipment for the job.

All Stratco Handi-Mate™ Sheds must be securely bolted to a permanent concrete base with sufficient masonry anchors securing all four corners of the

Handi-Mate™ shed to prevent wind uplift.

SHED WINDOWS (OPTIONAL)

Stratco Shed Windows are avaliable as an optional add-on, avaliable in both Louvre and Sliding variations. Refer to the “Window Installation” section if

installing a Stratco Window, or visit your local Stratco store for more information.

FLOORING PREPARATION

The installer is responsible for ensuring the slab or concrete pads are sufficient to support the shed and sustain wind loading.

Do not directly anchor your shed to pavers.

Option 1 - Before building the shed, pour a base that is larger than the area by at least 200mm in each direction. The base should be poured so the concrete

outside the shed floor area slopes away from the shed to help prevent water from entering the shed.

Option 2 - Substantial concrete pads may be used at each anchor location as an alternative to a complete concrete floor. It is recommended pads are

minimum Ø250mm x 400mm deep, embedded into a firm natural soil base.

IMPORTANT NOTES:

1. It is essential to clear and level the site prior to assembling your Stratco Handi-Mate™ Shed.

2. Note there are different types and colours of screws. Ensure that the right type and colour screw is being used at each location.

3. Stability and performance of the shed relies on the door being closed during high wind events.

4. Do not traverse the roof of the Handi-Mate™.

5. Use heavy gloves when handling steel sheeting and flashings and never attempt to install a shed in windy conditions.

BEFORE YOU START

HANDI-MATE™ MODEL SIZES

525mm

825mm

1525mm

2210mm

825

1860mm

1855mm 2220mm

2210

2210mm

2900

ws sws cws

ws sws

cws

ws cws

cws

cws ws

cws

cws ws

cws

cws cws sws

cws sws

cws

csws sws

cws

525mm

825mm

1525mm

2210

825

1860mm

1855mm 2220mm

2210mm

2210

2900

ws sws cws

ws sws

cws

ws cws

cws

cws ws

cws

cws cws sws cws sws

cws sws

cws

csws sws

cws

525mm

825mm

1525mm

2210mm

825

1860mm

1855mm 2220mm

2210mm

2900

ws sws cws

ws sws

cws

ws cws

cws

cws ws

cws

cws ws

cws

cws sws cws sws cws sws

cws

csws sws

cws

Handi-Mate™ 1

525mm

825mm

1525mm

2210mm

825

1860mm

1855mm 2220mm

2210mm

2900

ws sws cws

ws sws

cws

ws cws

cws

cws ws

cws

cws cws sws cws sws cws sws

cws

csws sws

cws

Handi-Mate™ 2

525mm

825mm

1525mm

2210mm

825

1860mm

1855mm 2220

2210mm

2900

ws sws cws

ws sws

cws

ws cws

cws

cws ws

cws

cws ws

cws

cws sws

cws sws cws sws

cws

csws sws

cws

Handi-Mate™ 3

Handi-Mate™ 4

Handi-Mate™ 5

TOOLS REQUIRED

Rivet Gun Power Drill Phillips Head Driver Hex Head Driver Adjustable Spanner 3.5mm & 12mm Drill Bit

10mm Masonry Bit

Gloves Safety Glasses Step Ladder 2 x Trestle / Saw-horse Permanent Marker Tape Measure

Figure 1.0

Refer to the following figures for wall sheeting configurations.

Corner Wall Sheet - CWS

Split Wall Sheet - SWS

Wall Sheet - WS

COMPONENTS

Figure 1.1

Ridge Cap Ridge Beam

Door Shroud

Barge Support Sliding Rail Bottom Channel Runner Rail Wall Channel

L/H Barge Cap R/H Barge Cap Top Door

Channel

Bottom Door

Channel

Vertical

Door Channel

Door Jamb

COMPONENTS

Figure 1.2

Split Wall Sheet Split Door Sheet Corner Wall Sheet Wall Sheet

Roof Sheet Coloured Rivet Aluminium Rivet

10x16 Wafer-Head

Screw

10x22 Wafer-Head

Screw

10x25 Self-Drilling

Coloured Screw

(with neo washer)

10x16 Self-Drilling

Screw

(with neo washer)

10x16 Self-Drilling

Screw

Door Handle Door Tongue Door Latch Hold Down Lug M8x47 Masonry

Anchor

Door Wheel Door Nut Door Stop Corner Bracket Handle Mount

WALL ASSEMBLY

10x16 self-drilling screw

Wall Channel

Corner Wall Sheet

Split Wall Sheet

Wall Channel

Wall Sheet

Once all Wall Sheets are lapped the Wall Channels can be fitted. Fit the

Wall Channel over the lapped Wall Sheets. The end of the Wall Channel

should fit up against the end of the Corner Wall Sheet (Figure 1.6).

End View

Wall Channel

Figure 1.3

Note: All Handi-Mate™ walls are assembled in the same

manner. Refer to “Handi-Mate™ Model Sizes” section for

specific wall sheeting quantities & configurations.

Handi-Mate Window Assembly

Stratco Shed Windows are avaliable as an optional add-

on. Refer to the “Window Installation” section at the

end of this document if installing a Stratco Window, or

visit a Stratco store for more information.

Figure 1.6

When assembling the Wall and Door Sheets, lay the sheets down on

trestles/blocks (Figure 1.4). This will make assembly easier and reduce the

risk of damage to components.

All underlap sheets can be identified as

having a stepped ridge.

Corner Wall Sheet

Trestles / Blocks

Figure 1.5

Figure 1.4

Ignore

Wall Channel

Pilot hole

Figure 1.7

Place the Corner Wall Sheet down first. Lay the next Wall Sheet

overlapping the Corner Wall Sheet (Figure 1.5). Subsequent Wall Sheets

can be overlapped in the same manner. Refer to “Handi-Mate™ Model

Sizes” section for specific wall sheet configurations.

Ensure pre-made pilot holes in the Wall Channel line up in the centre of

the Wall Sheet crests (Figure 1.7). Pulling the Wall Sheet into place may

be required to achieve this.

Note: Ignore the final two holes at the ends of the Wall Channels.

Fasten the top and bottom Wall Channels to the Wall Sheets using 10x16

self-drilling screws through each pilot hole, ignoring the two holes at each

end (Figure 1.8).

10x16 self-drilling screw

Wall Channel

Figure 1.8

Figure 1.9

Coloured Rivet

Repeat this process to assemble the remaining walls. A left wall, right wall

and rear wall should be assembled before continuing.

Bottom Channel

10x16 self-drilling screw

Figure 2.1

Lay out sheets onto trestles/blocks. Refer to figure 1.5 for lapping details. Fit

the Bottom Channel and Sliding Rail over theWall Sheets (Figure 2.1).

The end of the Channels should fit up against the ends of the Corner

Wall Sheet (Refer Figure 1.6).

FRONT WALL ASSEMBLY

Figure 2.0

Note: All Handi-Mate™ front walls are assembled in the

same manner.Refer to“Handi-Mate™ Model Sizes” section

for specific front wall sheeting quantities & configurations.

Sliding Rail

Bottom Channel

Door Jamb

10x16 self-drilling screw

Door Jamb

Corner Wall Sheet

Split Wall Sheet

Top

Sliding Rail

Bottom Channel

Fasten one 10x16 self-drilling screw through the third pilot hole of the

Bottom Channel and into the corresponding Wall Sheet crest (Figure 2.2).

Fasten another 10x16 self-drilling screw through the third pilot hole of the

Sliding Rail and into the Wall Sheet.

Figure 2.2

Sheet Layout

Join any overlapping sheets to one another using coloured rivets through

the mid-span of lapping crests (Figure 1.9).

Drill a hole with the ø3.5mm drill bit into the centre of the lapping crests.

Use a Rivet Gun to rivet the sheets together.

Fit the Door Jamb over the Wall Sheet, ensuring it is inside the Bottom

Channel and Sliding Rail (Figure 2.3).

Fasten one 10x16 self-drilling screw through the underside of the Bottom

Channel & Sliding Rail and into the Door Jamb (Figure 2.5).

Figure 2.3

Figure 2.6

Door Jamb

Sliding Rail

Bottom Channel

Sliding Rail

Bottom Channel

10x16 self-drilling screw

Figure 2.5

Door Jamb

Approx.

150mm

Coloured Rivet

DOOR ASSEMBLY

Figure 3.0

Bottom Door Channel

Vertical Door Channel

Top Door Channel

Vertical Door Channel

Wall Sheet

Split Door Sheet

10x16 wafer screw

Note:All Handi-Mate™ doors are assembled in the same manner.

Figure 2.4

Sliding Rail

Bottom Channel

10x16 self-drilling screw

Door Jamb

Slide the other Door Jamb approximately 150mm into the Bottom

Channel and Sliding Rail. Ensure the open end of the Door Jamb is facing

away from the sheets (Figure 2.6). A coloured rivet should be used to join

sheet overlaps together (Refer Figure 1.9).

Crest-Fix the Bottom Channel & Sliding Rail to the wall sheets using

three 10x16 self-drilling screws through the pilot holes in each (Figure 2.4).

Ensure all sheets are crest-fixed.

Ensure the door is square. Check the diagonal measurements from corner

to corner of the door (dashed lines, Figure 3.7).The diagonal measurements

should be equal for the door to be square.

Ensure the lip of the Top and Bottom Door Channels fit over the Vertical

Door Channels (Figure 3.5).

Fasten the Handle Mounts through the pilot holes in the Vertical Door

Channel with two 10x16 wafer screws (Figure 3.3).

Handle Mounts

Vertical Door Channel

Figure 3.2

Fit the two Handle Mounts into the Vertical Door Channel (Figure 3.2).

The two Handle Mounts are the same component, so can be installed in

either order.

Door Nut

Top Door Channel

Door Wheel

Figure 3.1

Fix the DoorWheels to the Top Door Channel using Door Nuts (Figure 3.1).

10x16 wafer screws

Figure 3.3

Vertical Door Channel

Bottom Door Channel

Top Door Channel

Sheet Layout

Wall Sheet

Split Door Sheet

Figure 3.4

10x16 wafer screws

Figure 3.6

Figure 3.5

Top / Bottom

Door Channel

Vertical

Door Channel

Figure 3.7

10x16 wafer screws

Figure 3.8

Lay out sheets onto trestles/ blocks. Refer to figure 1.5 for lapping details. Fit

the Vertical Door Channels over the side of the door sheets, then fit the

Top and Bottom Door Channels over the door sheet ends. Set the door in the square position by fastening two 10x16 wafer screws

through the pilot holes on the underside of each corner. (Figure 3.8).

Fasten one 10x16 wafer screw through the pilot holes in the corner of each

Top & Bottom Channel (Figure 3.6).

Crest-fix 10x16 wafer screws through the Top Door Channel and into the

ridges either side of the Door Roller (Figure 3.9).

Handle Mount

Using the pilot holes in the Handle Mounts as a guide, drill a ø3.5mm pilot

hole, then ø12mm hole through the wall sheet (Figure 3.11).

Figure 3.11

Coloured Rivet

A coloured rivet should be used to join sheet overlap together (Refer

Figure 1.9).

Figure 3.12

Top Door Channel

10x16 wafer screws

Figure 3.9

Vertical Door Channel

10x16 wafer screws

Figure 3.10

Crest-fix two 10x16 wafer screws through the pilot holes in each side of the

Handle Mounts (Figure 3.10).

ERECTING WALL ASSEMBLIES

The wall assemblies can now be joined together.

Wall Assemblies should be erected and joined together in the order indicated

by the numbered arrows below (Figure 4.0).

Left Wall

Front Wall

Fit the Corner of the Front Wall over the left side Wall Sheet (Figure 4.1).

Figure 4.0 Figure 4.1

Front Wall

Left Wall

Right Wall

Rear Wall

Corner Bracket

Top Channel

Figure 4.2

Fit the Corner Bracket over the Top Wall Channels. Ensure the pilot holes

of the Corner Bracket and Wall Channels line up (Figure 4.2).

10x16 self-drilling screw

Corner Bracket

Top Channel

Figure 4.3

Fasten through the Corner Bracket pilot holes and into the Top Channels

using 10x16 self-drilling screws (Figure 4.3).

10x16 self-drilling screw

Corner Bracket

Figure 4.6

Fit the Bottom Corner Brackets of all four corners over the Bottom Wall

Channels. Fasten through the Corner Bracket pilot holes and into the

Door Channel using 10x16 self-drilling screws (Figure 4.6).

Door Shroud

Door Jambs

Figure 4.5

Use the Door Shroud as a guide to set the correct spacing between the

Door Jambs. Fit the Corner Bracket as per Figure 4.2 - 4.3.

Door Jamb

Sliding Rail

Corner Wall Sheet

(Right Wall)

Fit the Remaining Wall Assemblies as per Figure 4.1 - 4.3.

The unfixed Door Jamb must be moved into position before fixing the

Right Wall Assembly to the Front Wall Assembly.

Slide the Door Jamb over the corner of the Right Wall Sheet (Figure 4.4).

Figure 4.4

Door Jamb

10x16 self-drilling screw

Figure 4.7

Fasten two 10x16 self-drilling screws through pilot holes in the Door Jamb

and into the Corner Sheet (Figure 4.7).

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Stratco Deposito all'aperto

Stratco

Stratco PL-5716 Manuale utente

Manuali Deposito all'aperto popolari di altre marche

USP

USP DURAMAX 10 Ft x 8 Ft StoreMax Plus Manuale utente

TYGO

TYGO Nyland Manuale utente

Duratuf

Duratuf GL105 Manuale utente

Viking

Viking SD5300SS Manuale tecnico

USP

USP DURAMAX Apex Pro 10.5 Ft x 8 Ft 40116 Manuale utente

ModuLaro

ModuLaro Lojo WC202200 Manuale utente

Lifetime

Lifetime 6418 Manuale utente

rollaway container

rollaway container ARPCA24 Manuale utente

Duratuf

Duratuf Havelock Manuale utente

X-METAL

X-METAL 4065 Manuale utente

Outdoor Life Products

Outdoor Life Products FP2030 F Manuale utente

Royalcraft

Royalcraft Faro 295L Storage Box Manuale utente

Riverlea

Riverlea Duratuf KIWI KS3 Manuale utente

OLT

OLT GS84D-FJ-Plywood Manuale utente

Rubbermaid

Rubbermaid 5L45 Manuale utente

garofalo

garofalo TUSCANY EVO Manuale utente

Duratuf

Duratuf Kiwi MK1 Manuale utente

Eden

Eden CA2988 Manuale utente