Struers Accutom-5 Manuale utente

Manual No.: 14947001

Date of Release 15.11.2012

Accutom-5

Instruction Manual

Accutom-5

Instruction Manual

Table of Contents Page

User’s Guide...............................................................1

Reference Guide.......................................................25

Quick Reference Guide ............................................47

Always state Serial No and Voltage/frequency if you have technical questions or when ordering spare parts.

You will find the Serial No. and Voltage on the type plate of the machine itself. We may also need the Date

and Article No of the manual. This information is found on the front cover.

The following restrictions should be observed, as violation of the restrictions may cause cancellation of

Struers legal obligations:

Instruction Manuals: Struers Instruction Manual may only be used in connection with Struers equipment

covered by the Instruction Manual.

Service Manuals: Struers Service Manual may only be used by a trained technician authorised by Struers.

The Service Manual may only be used in connection with Struers equipment covered by the Service Manual.

Struers assumes no responsibility for errors in the manual text/illustrations. The information in this manual is

subject to changes without notice. The manual may mention accesso

ries or parts not included in the present

version of the equipment.

Original instructions. The contents of this manual is the property of Struers. Reproduction of any part of

this manual without the written permission of Struers is not allowed.

Struers A/S

Pederstrupvej 84

DK-2750 Ballerup

Telephone +45 44 600 800

Fax +45 44 600 801

Accutom-5

Instruction Manual

Accutom-5

Safety Precaution Sheet

To be read carefully

before use

1. The operator should be fully instructed in the use of the machine and its

cut-off wheels according to the Instruction Manual and the instructions

for the cut-off wheels.

2. The machine must be placed on a safe and stable support table.

3. Be sure that the actual voltage corresponds to the voltage stated on the

back of the machine. The machine must be earthed.

4. Use only intact cut-off wheels. The cut-off wheels must be approved for

min. 3000 rpm. If other cut-off wheels or saw blades are used, make

sure that the speed setting of Accutom-5 complies with the max. speed

for the cut-off wheels or saw blades.

5. Observe the current safety regulations for handling, mixing, filling,

emptying and disposal of the additive for cooling fluid.

6. The sample must be securely fixed in the specimen holder.

7. Do not touch the sample, the specimen holder head or the cut-off wheel

while positioning the sample with the POSITION controls.

8. Never try to open the cover before the cut-off wheel has stopped

completely.

The equipment should only be used for its intended purpose and as detailed in the Instruction Manual.

The equipment is designed for use with consumables supplied by Struers. If subjected to misuse, improper

installation, alteration, neglect, accident or improper repair, Struers will accept no responsibility for

damage(s) to the user or the equipment.

Dismantling of any part of the equipment, during service or repair, should always be performed by a qualified

technician (electromechanical, electronic, mechanical, pneumatic, etc.).

Accutom-5

Instruction Manual

Disposal

Equipment marked with a WEEE symbol contain electrical and

electronic components and must not be disposed of as general

waste.

Please contact your local authorities for information on the correct

method of disposal in accordance with national legislation.

Accutom-5

Instruction Manual

User’s Guide

Table of Contents Page

1. Getting Started 3

Checking the Contents of Packing.....................................................3

Placing Accutom-5.............................................................................3

Getting Acquainted with Accutom-5...................................................3

Supplying Power ................................................................................4

Changing the voltage setting ....................................................4

Recirculation Unit...............................................................................6

Software Settings...............................................................................7

Configuration Menu...................................................................7

Setting the Language................................................................8

2. Basic Operations 9

Using the Controls..............................................................................9

Front Panel Controls of Accutom-5...........................................9

Groups of Keys.........................................................................9

Acoustic Signals........................................................................9

Location of Main Switch............................................................9

Front Panel Controls ........................................................................10

Display....................................................................................11

Reading the Display.........................................................................12

Changing/Editing Values..................................................................13

Numeric Values.......................................................................13

Alphanumeric Values..............................................................14

Positioning the Sample ....................................................................15

Reference Position..................................................................15

Absolute Position....................................................................15

Relative Position.....................................................................15

Relative Zero...........................................................................15

Stop Position...........................................................................15

Cutting..............................................................................................16

Changing the Cut-off Wheel....................................................16

Clamping the Sample and Specimen Holder..........................17

Positioning the Sample...........................................................17

Setting the Cutting Parameters........................................................18

Wheel......................................................................................18

Speed......................................................................................18

Feed........................................................................................18

Force.......................................................................................18

Rotation...................................................................................19

Water ......................................................................................19

Accutom-5

Instruction Manual

Starting the Cutting ..........................................................................19

During Cutting..................................................................................20

Changing the Feed Speed......................................................20

Retracting the Sample ............................................................20

Force Limit Reached...............................................................20

Stopping the Cutting.........................................................................21

Automatic Stop........................................................................21

Manual Stop............................................................................21

3. Maintenance

Daily Service ....................................................................................22

Checking the Recirculation Unit..............................................22

Weekly Service ................................................................................23

Refilling the Cooling Water Tank......................................................23

Emptying and Cleaning the Tank............................................23

Refilling the Tank....................................................................23

Maintenance of Cut-off Wheels........................................................24

Maintenance of Diamond and CBN Cut-off Wheels................24

Storing of Abrasive Cut-off Wheels.........................................24

Accutom-5

Instruction Manual

1. Getting Started

In the packing box you should find the following parts:

1 Accutom-5

2 Mains cables

1 Specimen Holder with parallel vice

1 Flange for cut-off wheels (42 mm dia.)

1 Stop pin

1 Spanner, 17mm

1 Small grate

1 Large grate

1 Allen key, 2 mm

1 Allen key, 2.5 mm

1 Allen key, 3 mm

1 Allen key, 4 mm

1 Allen key 5 mm

2 Screws M4x20

2 Screws M4x35

1 Set of Instruction Manuals

Accutom-5 should be placed on a stable and plane (tolerance

±1 mm) table. The table must be able to carry a weight of min. 50 kg.

Take a moment to familiarise yourself with the location and names of

the Accutom-5 components.

AFront panel/Front panel control(s)

BMain switch

CRecirculation Cooling Unit

DCut-off wheel

ESpecimen holder head

Checking the Contents of

Packing

Placing Accutom-5

Getting Acquainted with

Accutom-5

Instruction Manual

Always remember to switch the power off when installing electrical

equipment!

The factory setting for Accutom-5 is 240V.

Pull out the fuse holder from the cable terminal at the back of the

machine.

Pull out the voltage switch and turn it to the correct setting.

Voltage Required Setting

230 or 240V 240V

200 to 220V 200V

Note: The two additional settings, 110V and 120V are not to be used.

Reinsert the voltage switch.

Put the fuse holder back into the cable terminal.

Supplying Power

DANGER!

The machine must be earthed

IMPORTANT

Check that the mains voltage corresponds to the voltage stated

on the type plate on the back of the machine.

Changing the voltage setting

If the factory setting is not the correct setting for your mains supply the

setting can be changed from 240V to 220V:

Accutom-5

Instruction Manual

Accutom-5 is shipped with 2 types of Mains cables:

The 2-pin (European Schuko) plug is for use on single-phase

connections.

If the plug supplied on this cable is not approved in your country,

then the plug must be replaced with an approved plug. The leads

must be connected as follows:

Yellow/green: earth

Brown: line (live)

Blue: neutral

The 3-pin (North American NEMA) plug is for use on 3-phase power

connections.

If the plug supplied on this cable is not approved in your country,

then the plug must be replaced with an approved plug. The leads

must be connected as follows:

Green: earth

Black: line (live)

White: line (live)

Both cables are on the other end equipped with an IEC 320 cable

connector that has to be connected to the Accutom.

Single-phase Supply

3-phase Supply

Connection to the Machine

WARNING!

The output voltage from this cable is 200 – 240V and not 110V.

DO NOT use this cable to connect equipment that use a 110V power

supply. Failure to adhere to this may result in material damage.

Accutom-5

Instruction Manual

Pull out the recirculation tank.

Fill the tank with 3.88 l water and 120 ml Struers Additive for

cooling fluid. The water level should be 5 mm below the edge of

the front hole in the tank cover.

Check that the cover is fitted securely into place in the

recirculation tank and push the drawer with the recirculation tank

into place again.

Check that the end of the inlet tube has dropped into position.

Recirculation Unit

IMPORTANT

Always ensure that there is sufficient water in the tank as the recirculation

pump will be damaged if it is run dry.

Note:

Changing of cooling water should be done at least once a month.

IMPORTANT

Always maintain the correct concentration of Struers Additive in the cooling

water (percentage stated on the container of the Additive). Remember to

add Struers Additive for cooling fluid each time you refill with water.

Do not use any oil, petrol, or turpentine-based additives, only Struers

additive.

Indice

Lingue:

Altri manuali Struers Macchina troncatrice

Struers

Struers Minitom Manuale utente

Struers

Struers Discotom-50 Manuale utente

Struers

Struers Unitom-2 Manuale utente

Struers

Struers Accutom-50 Manuale utente

Manuali Macchina troncatrice popolari di altre marche

Monosem

Monosem MICROSEM Manuale utente

Matco Tools

Matco Tools MT2872L Manuale utente

Silver Eagle

Silver Eagle SE510 Manuale utente

Rockwood

Rockwood 31741 Manuale utente

Stihl

Stihl TS 700 Manuale utente

skilsaw

skilsaw SPT79A Istruzioni per il montaggio

Milwaukee

Milwaukee MXF COS350 Manuale utente

Parkside

Parkside 304732 Manuale utente

DWT

DWT KF04-30 Manuale utente

Hitachi

Hitachi CC 16SB Manuale utente

Sumake

Sumake ST-CT150 Manuale utente

Sumake

Sumake ST-CT100 Manuale utente

Sealey

Sealey G3 Series Manuale utente

Trojan

Trojan CT-300 Manuale utente

Makita

Makita XOC01 Manuale utente

Cornwell Tools

Cornwell Tools CAT850XLR Manuale utente

Hitachi

Hitachi CC 14SE Manuale

Kamasa-TOOLS

Kamasa-TOOLS K 9836 Manuale utente