STT Condigi CareCom IP Manuale utente

CareCom IP

K1122

Installation Guide

STT Condigi

Agnesfridsvägen 113 A

212 37 Malmö

Sweden

Table of Contents

1 Introduction .............................................................................. 3

2 Installation................................................................................. 4

2.1 Programming Mode..................................................................... 4

2.2 The Buttons Functions in Programming Mode.................. 4

2.3 Local Number................................................................................. 4

2.4 Local IP.............................................................................................. 5

2.5 Server IP ........................................................................................... 5

2.6 ARM Flash/Edit Address/Set default EE ................................ 5

3 Mounting ................................................................................... 5

4 Power Supply and Connection to Network......................... 6

4.1 Power Supply and Network Cable.......................................... 6

4.2 Connection...................................................................................... 6

5 How to add a CareCom IP Room Unit to the

Swan CareCom System............................................................ 7

5.1 Conguring 3CX Settings .......................................................... 7

5.2 Conguring the CareCom IP..................................................... 8

5.3 Conguring the Equipment in the Swan CareCom

(TeleVagt) Data Base........................................................................... 10

5.4 Conguring the ctCareComServer......................................... 12

5.5 Conguring the ctDisplayServer............................................. 13

1 Introduction

CareCom IP is a room unit, which has speech (full duplex phone quality),

presence marking and alarm handling.

Furthermore, the CareCom IP has a display with the possibility to view

active alarms.

If viewing alarms is activated, it is possible to acknowledge the alarms

and to establish a 2-way conversation between the CareCom IP and the

device that has given the alarm.

CareCom IP is mounted on a wall and is connected to a POE switch/router.

Furthermore CareCom IP has two inputs and two outputs.

2 Installation

2.1 Programming Mode

Installation of CareCom IP is done in the programming mode, which is

accessed by holding down the red button while connecting the net-

work cable. The display will then look like the illustration bellow.

Local Number

Local IP

Local Mask

Server IP

ARM Flash select

Edit Address

Set default EE

ESC UP DOWN ENT

Local Number

301_____________

–

ESC< + – >ENT

2.2 The Buttons Functions in Programming Mode

Below the display you will nd four buttons, which are used for pro-

gramming. The four buttons are:

Escape/back Up Down Enter/forward

2.3 Local Number

Local number is set by selecting “Local Number”. Press “Enter” (red button)

when the check mark is next to “Local Number”. Press “+” (button with a

check mark) for higher numbers, “-” (button with a cross) for lower num-

bers and use the “ESC” and “ENT” to go forward or backward. Finally, press

several times on ENT until you exit the program and automatically saves

the setting.

2.4 Local IP

Local IP addresses is setup in the same way as a local number.

PLEASE NOTE: The local IP is the IP of the room unit. The room unit must be

connected to the network and may not conict with existing IP addresses.

See appendis and plan for IP addresses from page 10.

2.5 Server IP

Server IP is setup in the same way as a local number.

2.6 ARM Flash/Edit Address/Set default EE

These three functions are not used.

3 Mounting

CareCom IP is mounted on a wall – in the included wall bracket.

The illustration is viewed from the wall.

I/O

1. Digital In 1 (Alarm)

2. Digital In 2 (Door alarm)

3. NC

4. DC power (out +12V)

5. Ground

6. NC

7. Digital Out 1 (Alarm LED)

8. Digital Out 2 (Presence LED)

Connection for network

4 Power Supply and Connecting to Network

4.1 Power Supply and Network Cable

CareCom IP has two RJ45 connectors:

For power supply

For network

I/O

4.2 Connection

When the CareCom IP is connected, the small LED will ash yellow until

the network is found. When the network is found, the LED will change to

green for approx. one minute. After that, it will turn o.

LED

Connections can be made

directly into the back of the

CareCom IP or via a socket

(K9005) shown below. In this

case, you need two connectors

(S03.242 and S03.248).

DC power

34 5678

IN1

IN2

OUT1

OUT2

+24V

GND

J2J1

+24V

5 How to add a CareCom IP Room Unit to the Swan CareCom System

In the below mentioned examples the screen shots are only indicative.

Prerequisite:

The CareCom Server must be version 5.2.0 or above. The CareCom IP

room unit must have rmware version 1.2.10.

5.1 Conguring 3CX Settings

Follow these steps to dene the CareCom IP in 3CX.

Note: This is needed even if the speech option is not used.

1. Start the 3CX Windows Management Console.

4. In the group “Authentication”type in “ID” equal to the Extention Number

and a password. Remember the password as you are using this later.

5. Scroll down and click “OK” to save the changes.

5.2 Conguring the CareCom IP

Follow these steps to congure the CareCom IP in the

ctLinkCareComServer User Interface.

1. Start the ctLinkCareComServer User Interface from the taskbar

(see next page).

2. In the menu “Add” select “Extension”.

3. In the group “User Information” type in the “Extension Number”

dened while installing the CareCom IP.

2. Select the new CareCom IP and click the pencil icon to edit the

conguration.

3. Set the “Input Notication” to “Input I/O Normally Open”.

4. Set the “Display Group”.

5. Click “SIP Account”.

6. Type in the Extension Number dened in the 3CX and click “OK”.

7. Type in the password dened in the 3CX and click“OK”.

8. Click the diskette icon to save the changes.

5.3 Conguring the Equipment in the Swan CareCom (TeleVagt) Data Base

Follow these steps to congure the CareCom IP in the Swan CareCom

(TeleVagt) Data Base.

1. Start the Swan CareCom (TeleVagt) Data Base.

2. Double click any equipment in the Customer Equipment List.

3. Click the menu New.

4. In the Field Equipment ID type in 10000<new extension>

where <new extension> is the three digit extension.

5. Drag a CareCom Zone into the eld Zone Denition.

6. Click the menu “Save” to save the changes.

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Sistema di sicurezza popolari di altre marche

Inner Range

Inner Range Concept 2000 Manuale utente

Climax

Climax Mobile Lite R32 Istruzioni per il montaggio

CADDX

CADDX NX-6 Manuale utente

FBII

FBII XL-31 Series Manuale utente

Johnson Controls

Johnson Controls PENN Connected PC10 Manuale utente

Aeotec

Aeotec Siren Gen5 Manuale utente

Blaupunkt

Blaupunkt SA 2700 Manuale utente

IDEAL

IDEAL Accenta Manuale del proprietario

AJAX

AJAX DoubleButton Manuale utente

Swann

Swann SW-P-MC2 Manuale utente

Ecolink

Ecolink Siren+Chime Manuale utente

Digital Monitoring Products

Digital Monitoring Products XR150 Manuale utente

EDM

EDM Solution 6+6 Wireless-AE Manuale utente

Highway Safety Group

Highway Safety Group EA401 Manuale utente

Siren

Siren LED GSM Manuale utente

Detection Systems

Detection Systems 7090i Istruzioni per il montaggio

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuale utente

Siemens

Siemens FDM273 Manuale utente