Stylmark Optima LED DS5 Perimeter Lit Manuale utente

Part Number# 971830

Rev B (05/16)

Stylmark, Incorporated ♦6536 Main Street NE, PO Box 32008 ♦Minneapolis, MN 55432

1-800-328-2495 ♦www.stylmark.com

Figure 1

Installation Instructions

Optima LED® 5” Double-Sided

StretchLite Perimeter Lit

Graphic Display

INSTALLATION INSTRUCTIONS

Before you begin

These instructions illustrate the Stylmark Optima LED®

5” Double-Sided StretchLite Perimeter Lit Graphic

Display.If you have questions during assembly, call

800-328-2495, Monday – Friday, 8:00am to 4:30pm, to

request technical assistance.

Please read these instructions carefully before beginning installation.

Tools you’ll need

•Phillips Head Screwdriver

•3/16” Hex Key Wrench

Line Voltage

Connector Optima LED DS5 (Double-sided StretchLite

Graphic Display) with Graphics

Optima LED DS5 (Double-sided StretchLite

Graphic Display) without Graphics

Low Voltage

Connector

Power Supply

LED Light Strip

Extrusion

Cross-Section

Corner Bracket

Splice Bracket

Y-Bracket

Clevis Pin &

Cotter Pin in Collar

Support Tube

Part Number# 971830

Rev B (05/16)

Stylmark, Incorporated ♦6536 Main Street NE, PO Box 32008 ♦Minneapolis, MN 55432

1-800-328-2495 ♦www.stylmark.com

Getting Started:

These instructions are for an Optima LED® 5” Double-Sided

StretchLite Perimeter Lit Graphic Display. Follow the instructions

for the display ordered.

Please review all electrical requirements on the label before

connecting. Do not use improper current.

If the unit is hard-wired, a qualified electrician should perform

electrical installation.

This display, or sign, is intended to be installed in dry locations only

and in accordance with the requirements of Article 600 of the

National Electrical Code and/or other applicable local codes. This

includes proper grounding and bonding of the display.

It is recommended that the frame of this display be constructed on

a horizontal surface (such as a table, or the floor) to ensure a tight

fit at all corners and splices. When assembled, the frame should be

lifted into a vertical position.

Step-by-Step Instructions – Unpacking:

1. The frame of the Optima LED® 5” Double-Sided StretchLite

Perimeter Lit Graphic Display is shipped in segments in

multiple, labeled boxes. Ensure that all boxes are present

and ready for unpacking. Boxes are labeled “Box 1 of x”,

etc., where x is the total number of boxes.

2. Unpack all frame segments and arrange on a clean, flat

surface. Each segment has two ends: corner ends are

mitered, and are labeled A through D, while intermediate

ends, if present, are flat, and are labeled E through K.

3. All corners will be made up of two mitered segments that

have matching labels (ie, A to A, B to B). Arrange corner

pieces perpendicular to each other. See Figure 2.

4. If there are frame segments with intermediate ends, match

the labels (ie. E to E, F to F) to align adjoining pieces.

When complete, there will be a single rectangle of

segments. See Figure 3.

5. Larger frames will have one or more support poles and

corresponding splice brackets to hold them in place. If

there are support poles included, set them aside until

needed. See Figure 1.

6. Mounting hardware – if the sign was ordered with mounting

hardware (pedestal, feet, etc.) set it aside until needed.

Stylmark Installation Instructions: Optima LED® DS5 Perimeter Lit

Figure 3

Figure 2

Corner

Bracket

Mitered End

Figure 4

Y-Bracket

Cover

Part Number# 971830

Rev B (05/16)

Stylmark, Incorporated ♦6536 Main Street NE, PO Box 32008 ♦Minneapolis, MN 55432

1-800-328-2495 ♦www.stylmark.com

Stylmark Installation Instructions: Optima LED® DS5 Perimeter Lit

Step-by-Step Instructions - Frame Assembly - Corners:

1. Corners are secured together with corner brackets. A corner

bracket is pre-installed in one of the two corner segments of

each corner. See Figure 2.

2. Use a Philips head screwdriver to remove the cover piece

from a corner segment without the corner bracket and retain

the screws. A receiving Y bracket with a socket head cap

screw and protective cap will be exposed. See Figure 4.

3. Remove the protective cap and socket head cap screw from

the Y bracket. Discard the cap.

4. Slide the corner bracket into receiving frame segment under

the Y bracket.

5. Align the hole in the Y bracket with the hole in the corner

bracket. Insert the socket head cap screw through the Y

bracket into the corner bracket and tighten with a 3/16” hex

key wrench until the corner segments are firmly secured

together. See Figure 5.

6. If the outside corner of the display frame is not aligned

properly, more adjustments will be necessary.

a. Remove the cover from the adjoining segment with a

Phillips head screwdriver and retain the screws. This

will expose the other side of the corner bracket with a

second Y bracket connected to it with a socket head

cap screw.

Caution: There may be wiring that extends between

a cover with lights and the frame segment it was

attached to. Use caution when removing the cover.

b. Adjust the socket head cap screws on both sides of

the corner bracket using a 3/16” hex key wrench,

until the outside corner of the frame is aligned as

desired.

c. Re-secure the cover section of the adjoining segment

to the frame segment with the retained screws using

a Phillips head screwdriver. Make sure not to crimp

any wires under the edge of the cover.

7. If there are electrical connectors present, connect them now.

For example, insert a male low voltage connector into a

female low voltage connector. See Figure 6.

8. Tuck all wires and connectors under the covers and re-secure

the cover piece to the corner segment with the retained

screws using a Philips head screwdriver. Make sure not to

crimp any wires under the edge of the cover.

9. Repeat these steps for the 3 other corners of the frame. If

there are no frame segments with intermediate (flat) ends,

the frame assembly will be complete. See Figure 7.

Figure 7

Figure 5

Figure 6

Low Voltage Connector

Line Voltage Connector

Part Number# 971830

Rev B (05/16)

Stylmark, Incorporated ♦6536 Main Street NE, PO Box 32008 ♦Minneapolis, MN 55432

1-800-328-2495 ♦www.stylmark.com

Step-by-Step Instructions – Frame Assembly –

Intermediate Segments:

1. Frame segments with intermediate ends are connected

together with splice brackets.One end of the splice

bracket is pre-installed in an intermediate segment. See

Figure 8.

2. Ensure that the two segments to be connected have

matching labels, for example, F to F. Align the two

segments end to end. See Figure 9.

3. Using a Phillips head screwdriver, remove the cover on

the frame segment that does not have the splice bracket.

Retain the screws. A receiving Y bracket with a socket

head cap screw and protective cap will be exposed. See

Figure 10.

Caution: There may be wiring that extends between a

cover with lights and the frame segment it was attached

to. Use caution when removing the cover.

4. Remove the protective cap and the socket head cap screw

from the Y bracket. Discard the cap.

5. Slide the splice bracket into the receiving frame segment

under the Y bracket.

(Continued on next page)

Stylmark Installation Instructions: Optima LED® DS5 Perimeter Lit

Figure 9

Figure 8

Top View

Splice Bracket

Side View

Figure 10

Part Number# 971830

Rev B (05/16)

Stylmark, Incorporated ♦6536 Main Street NE, PO Box 32008 ♦Minneapolis, MN 55432

1-800-328-2495 ♦www.stylmark.com

Step-by-Step Instructions – Frame Assembly –

Intermediate Segments (Cont.):

6. Align the hole in the Y bracket with the screw hole in the

Splice Bracket. Insert the socket head cap screw and

tighten with a 3/16” hex key wrench until the two

intermediate segments are firmly secured together. See

Figure 11.

7. If there are wire connectors present, connect them now.

For example, insert a male line voltage connector into a

female line voltage connector. See Figure 12.

8. Tuck all wires and connectors under the covers and re-

secure the cover section to the frame segment with the

retained screws using a Philips head screwdriver. Make

sure not to crimp any wires under the edge of the cover.

9. Repeat these steps for all other intermediate segments of

the frame.

Stylmark Installation Instructions: Optima LED® DS5 Perimeter Lit

Figure 11

Figure 12

Low Voltage Connector

Line Voltage Connector

Part Number# 971830

Rev B (05/16)

Stylmark, Incorporated ♦6536 Main Street NE, PO Box 32008 ♦Minneapolis, MN 55432

1-800-328-2495 ♦www.stylmark.com

Step-by-Step Instructions – Display Frame Support Poles:

1. If the display came with support poles, these should be

inserted now. A support pole extends between 2

opposing splice brackets.

2. Remove the pre-installed clevis and cotter pins from the

collar of each splice bracket and retain.

3. Place one end of the first support pole in a collar, and

then place the second end in the opposing collar.

4. Align the holes in the support poles with the holes in the

collars. See Figure 13.

5. Place a clevis pin through the collar and support pole,

and use a cotter pin to secure. Repeat this step for the

other end of the support pole. See Figure 13.

6. Repeat this process for all support poles. Upon

completion, the display frame will be fully assembled.

See Figure 14.

Stylmark Installation Instructions: Optima LED® DS5 Perimeter Lit

Step-by-Step Instructions – Foot Mount Option:

Note: This option should be requested at time of order. The

number and type of feet required will vary based on the size of

the display frame, its orientation, and whether there are splice

brackets in the frame.

1. Determine the correct orientation of the frame (top,

bottom, left, right).

2. Position the feet so that they are in front of the frame,

aligned with each other, and near the screw holes for

each foot in the frame. A foot that goes under a Splice

Bracket will look different from a foot that attaches near

the corner of the frame. See Figure 15.

3. Remove the socket head cap screws that are pre-

installed in the feet and retain. Stand the display frame

up vertically and onto the mounting feet. See Figure

15.

4. With a Phillips head screwdriver, remove the cover(s) in

the bottom of the frame to expose mounting holes for

feet. Retain the screws.

Caution: There may be wiring that extends between

cover(s) with lights and the frame it was attached to.

Remove cover(s) carefully.

(Continued on next page)

Figure 13

Figure 14

Figure 15

Corner Foot

Splice Bracket Foot

Part Number# 971830

Rev B (05/16)

Stylmark, Incorporated ♦6536 Main Street NE, PO Box 32008 ♦Minneapolis, MN 55432

1-800-328-2495 ♦www.stylmark.com

Step-by-Step Instructions – Ceiling Suspended Option:

Note: This option should be requested at time of order.

Caution: Large display frames can be unwieldy to handle and

may require multiple people and/or equipment to lift into a

vertical position.

1. Locate the hanging Eyelets which will be pre-installed into

the top of the display frame. See Figure 18.

2. In accordance with local codes, mount all necessary

hardware to hang the display frame from the ceiling using

the position of the eyelets as reference.

3. Lift the display frame into the vertical position. Multiple

cables may be required to support each section of a large

frame. See Figure 19.

4. Plug the display frame’s power cord directly into a

standard, 3-prong, grounded wall or ceiling outlet.

Stylmark Installation Instructions: Optima LED® DS5 Perimeter Lit

Step-by-Step Instructions – Foot Mount Option (Cont.):

5. Align the mounting holes in the frame with the screw

holes in the feet. Using the provided socket head cap

screws, secure feet to the bottom of the frame with a

3/16” hex key wrench. See Figure 16.

6. Re-secure the cover(s) to the frame with the retained

screws using a Phillips head screwdriver. Make sure not

to crimp any electrical wires under the edge of the cover.

See Figure 17.

7. Plug the display frame’s power cord directly into a

standard, 3-prong, grounded wall outlet.

Caution: Local building codes may require additional means

to prevent the display frame from tipping. For example, the

feet of a large frame could be required to be bolted to the

floor. Verify if these, or other means, are necessary, and

install as required.

Figure 17

Figure 16

Foot

Mounting Holes

Figure 18

Hanging Cable

Eyelet

Figure 19

Multiple Hanging Cables

Part Number# 971830

Rev B (05/16)

Stylmark, Incorporated ♦6536 Main Street NE, PO Box 32008 ♦Minneapolis, MN 55432

1-800-328-2495 ♦www.stylmark.com

Step-by-Step Instructions – Graphic Installation:

A channel for the display graphic goes around the perimeter of

the display frame on both sides.

1. Insert the top corner of the silicone gasket of the first

graphic into the top corner of the channel, and then do

the same in the opposite bottom corner. Repeat with the

other two corners.

2. Insert the midpoint of the gasket into the channel on

each side (top, bottom, left, right).

3. Continue tucking the gasket into the channel, working

around the perimeter of the frame. Smooth out any

bunching or wrinkles.

4. Repeat on the other side of the display frame with the

second graphic.

5. To remove the graphic, pull on the tag. See Figure 21.

Stylmark Installation Instructions: Optima LED® DS5 Perimeter Lit

Step-by-Step Instructions – Pedestal Mount Option:

Note: This option should be requested at time of order. The

size and style of the pedestal will vary based on the size of the

display frame and its orientation.

1. Build the mounting pedestal following the instructions

enclosed with the unit.

2. Determine the correct orientation of the display frame

(top, bottom, left, right).

3. Attach the sides of the pedestal to the frame using a

socket wrench. The frame has pre-drilled bolt holes

that match the bolts provided with the pedestal.

4. Lift the display frame and pedestal into a vertical

position. Larger assemblies may require more than one

person to perform this task. See Figure 20.

5. Plug the display frame’s power cord into a standard, 3-

prong, grounded wall outlet

Figure 21

Figure 20

Manuali Monitor popolari di altre marche

Linear Acoustic

Linear Acoustic LQ-1000 Manuale utente

AOC

AOC I2579V Manuale utente

Gateway

Gateway FPD1520 Manuale utente

Furuno

Furuno Mu 120c Manuale utente

Asus

Asus VB171D - 17" LCD Monitor Manuale utente

Dell

Dell S2230MX Istruzioni utente

Philips

Philips 107C64 Manuale utente

Dell

Dell S2409WFP Manuale utente

EverFocus

EverFocus EN-7517E Manuale utente

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuale utente

Dell

Dell Precision 7680 Manuale di istruzioni

LG 50PM1M - - 50" Plasma Panel Manuale utente

Bosch

Bosch DDU 9 Manuale utente

Acer

Acer A231HL Manuale utente

Philips

Philips 86BDL4152T Manuale utente

NEC

NEC AccuSync LCD5V Manuale utente

Emay

Emay SleepO2 Manuale utente

IBM

IBM 6360 Istruzioni per l'installazione