Sub-Zero DEU1550B/L Manuale utente
Designer Series
Undercounter Refrigeration
Installation Guide
SPECIFICATIONS, INSTALLATION,
AND MORE
2 | Sub-Zero Customer Care 800.222.7820
Designer Series Undercounter Refrigeration
Contents
3Designer Series Undercounter Refrigeration
4Opening Dimensions
5Electrical Requirements
6Plumbing Requirements
6Preparation
7Anti-Tip Bracket
790° Door Stop
8Placement
8Alignment
9Water Line
10 Door Panel
12 Panel Installation
14 Completion
Features and specifications are subject to change at any
time without notice. Visit subzero.com/specs for the most
up-to-date information.
Important Note
To ensure this product is installed and operated as safely
and eciently as possible, take note of the following types
of highlighted information throughout this guide:
IMPORTANT NOTE highlights information that is especially
important.
CAUTION indicates a situation where minor injury or prod-
uct damage may occur if instructions are not followed.
WARNING states a hazard that may cause serious injury or
death if precautions are not followed.
IMPORTANT NOTE: Throughout this guide, dimensions in
parentheses are millimeters unless otherwise specified.
IMPORTANT NOTE: Save these instructions for the local
electrical inspector.
subzero.com | 3
Designer Series Undercounter Refrigeration
Product Information
Important product information, including the model and
serial number, are listed on the product rating plate. The
rating plate is located inside the cabinet, in the upper left
area of the unit. Refer to the illustration below.
If service is necessary, contact Sub-Zero Factory Certified
Service with the model and serial number. For the name of
the nearest Sub-Zero Factory Certified Service or for ques-
tions regarding the installation, visit the Product Support
section of our website, subzero.com, or call Sub-Zero
Customer Care at 800-222-7820.
RATING PLATE
Rating plate location
4 | Sub-Zero Customer Care 800.222.7820
Site Preparation
The depth of each model is 23⁄" (587). Allow for panel
thickness when planning the finished opening depth. A
minimum 3⁄" (89) finished return is required on all sides of
the opening. Framed cabinets require additional finished
filler material behind the face frame for a proper installa-
tion. Refer to the illustration.
DUAL INSTALLATION
If two units are installed side by side, a dual installation kit
may be required. Installations without a custom filler strip
require a dual installation kit. If a dual installation kit is not
specified, a 2" (51) filler strip is recommended between the
units. Dual installations without a filler strip can only be
accomplished using two units with opposite hinges. Refer
to the illustrations below.
Dual installation kits are available through an authorized
Sub-Zero dealer. For local dealer information, visit the
find a showroom section of our website, subzero.com.
For questions regarding the installation, call Sub-Zero
Customer Care at 800-222-7820.
DUAL OPENING WIDTH W
Two 15" Models 30" (762)
15" and 24" Models 39" (991)
Two 24" Models 48" (1219)
Dual installation kit required.
Opening Dimensions
DESIGNER SERIES UNDERCOUNTER MODELS
W
OPENING WIDTH
H
OPENING
HEIGHT
TOP VIEW
SIDE VIEWF
RONT VIEW
NOTE: 3
1/2" (89) finished returns will be visible and should be finished to match cabinetry.
3/4" (19)
TYPICAL
FRAMED
CABINETRY
W
FILLER
31/2" (89)
FINISHED
RETURN
FRAMELESS
CABINETRY
W
3/4" (19)
TYPICAL
31/2" (89)
FINISHED
RETURN
24" (610)
OPENING
DEPTH
WITHOUT FILLER STRIP FILLER STRIP
Opposite hinges
Same side hinges
OPENING DIMENSIONS W H
24" Model (standard height) 24" (610) 34⁄" (876)
24" Model (ADA height) 24" (610) 32⁄" (826)
15" Model (standard height) 15" (381) 34⁄" (876)
subzero.com | 5
Electrical Requirements
Installation must comply with all applicable electrical codes.
The electrical supply must be located within the shaded
area shown in the illustration below. A separate circuit
servicing only this appliance is required.
IMPORTANT NOTE: For indoor models, a ground fault cir-
cuit interrupter (GFCI) is not recommended and may cause
interruption of operation.
For the outdoor model, a ground fault circuit interrupter
(GFCI) is required to reduce the risk of electrical shock.
The electrical outlet must be positioned with the ground-
ing prong to the right of the thinner blades.
ELECTRICAL REQUIREMENTS
Electrical Supply 115 VAC, 60 Hz
Service 15 amp dedicated circuit
Receptacle 3-prong grounding-type
5"
(127) 2"
(51)
4"
(102)
FLOOR
OPENING
Electrical supply location
CAUTION
The outlet must be checked by a qualified electrician
to be sure it is wired with the correct polarity. Verify
the outlet is properly grounded.
WARNING
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly quali-
fied persons in order to avoid a hazard.
WARNING
Do not locate multiple portable socket-outlets,
power strip, or portable power supplies at the rear of
the appliance.
WARNING
Do not use an extension cord, two-prong adapter, or
remove the power cord ground prong.
Site Preparation
6 | Sub-Zero Customer Care 800.222.7820
Plumbing Requirements
MODEL DEU2450CI
Installation must comply with all applicable plumbing
codes.
For ease of installation, recess the water shut-o into the
wall or place it in an adjacent cabinet. Locate the water
supply line within the shaded area shown in the illustra-
tion below. Connect the water supply line to the house
supply with an easily accessible shut-o valve. Do not use
self-piercing valves.
An in-line filter is required when water conditions have a
high sediment content.
A reverse osmosis system can be used provided there is
constant water pressure of 35–120 psi (2.4–8.3 bar) supplied
to the unit at all times. A copper line is not recommended
for this application.
PLUMBING REQUIREMENTS
Water Supply Line ⁄" OD copper, braided
stainless steel, or PEX tubing
Water Pressure 35–120 psi (2.4–8.3 bar)
Excess Water Line for Connection 5' (1.5 m)
Preparation
Uncrate the unit and inspect for damage. Remove and
recycle packing materials. Do not discard the kickplate,
anti-tip bracket, and hardware.
Remove the kickplate by extracting the two mounting
screws. Refer to the illustration below.
SCREW
Kickplate removal
2"
(51)
4"
(102)
2"
(51)
OPENING
AREA EXTENDS
1/2" (13) FORWARD ON FLOOR
Water supply location
Site Preparation
subzero.com | 7
90° Door Stop
The door stop pins provided with the unit limit the door
swing to 90°.
IMPORTANT NOTE: If a 90° door opening is desired, the
pins must be installed prior to installing the unit into the
opening.
To install, open the door to approximately 80°. Insert one
pin into each hinge. Refer to the illustration below.
DOOR STOP PIN
90° door stop
Anti-Tip Bracket
WARNING
To prevent the unit from tipping forward, the anti-tip
bracket must be installed.
The anti-tip bracket should be attached to the wall behind
the unit with the bracket flange located ⁄" (6) above the
top of the unit. Refer to the illustration below. Failure to
properly position the anti-tip bracket will prevent proper
engagement.
1/4" (6)
ANTI-TIP
BRACKET
Anti-tip bracket
Site Preparation
8 | Sub-Zero Customer Care 800.222.7820
Alignment
LEVELING
Once the unit is in position, rotate the front legs clockwise
to raise and counterclockwise to lower. Rear height adjust-
ment can be made from the front. Using a Phillips drive,
turn clockwise to raise the unit or counterclockwise to
lower. Use the lowest torque setting when using a power
drill. Do not turn the leveling legs by hand. Refer to the
illustration below.
When the unit is properly leveled, door adjustments are
less likely to be necessary.
IMPORTANT NOTE: Level the unit to the floor, not the
surrounding cabinetry. This could aect the operation of
the unit, such as door closing.
WARNING
To reduce the possibility of the unit tipping forward,
the front leveling legs must be in contact with the
floor.
REAR
ADJUSTMENT
FRONT
ADJUSTMENT
Leveling
Installation
Placement
CAUTION
Before moving the unit into position, secure the door
closed and protect any finished flooring.
WARNING
When positioning the appliance, ensure the supply
cord is not trapped or damaged.
Use an appliance dolly to move the unit near the opening.
If the unit has been on its back or side, it must stand
upright for a minimum of 24 hours before connecting
power.
Plug the power cord into the grounded outlet. For model
DEU2450CI, insert the water supply line into the hole on
the back of the unit. Refer to the illustration below. Pull the
excess water line forward as the unit is slid into the open-
ing. Verify the anti-tip bracket is properly engaged.
BACK OF UNIT
HOLE FOR
WATER LINE
Water line (model DEU2450CI)
subzero.com | 9
Water Line
MODEL DEU2450CI
Under the unit, ⁄" plastic tubing is connected to the unit
with a preassembled ⁄" compression connection. The
water line fitting connection kit, provided with the unit,
contains a ⁄" compression union fitting for connection to
the household water line.
Purge the water line prior to final connection to the unit.
This will remove any debris that may be present in the
tubing from installing the new water line. Connect the
plastic tubing from the unit to the house water supply line
with the fitting connection kit provided. Refer to the
illustration below. Check all water line fittings for leaks.
IMPORTANT NOTE: Water lines cannot be exposed to
freezing temperatures.
WARNING
Connect to potable water supply only.
WATER LINE
CONNECTION
Water line connection
Installation
Alignment
ANCHORING
CAUTION
If using a power drill to predrill holes or install
screws, verify the drill chuck does not contact the
units face frame.
Adjust the depth of the unit to fit flush with the surround-
ing cabinetry. Allow for panel thickness. Once aligned,
verify the door opens properly, then install a #8 x ⁄" flat-
decorative head screw in each bracket.
WARNING
To avoid a hazard due to instability of the appliance,
it must be fixed in accordance with the instructions.
Anchoring
10 | Sub-Zero Customer Care 800.222.7820
Custom Panel
A custom door panel and handle hardware must be
installed.
A ⁄" (16) minimum to ⁄" (19) maximum thick panel is
required. The panel cannot exceed the maximum panel
weight indicated in the chart below. The depth of each
model is 23⁄" (587). Allow for panel thickness when plan-
ning the finished opening depth.
Minimum ⁄" (3) reveals are required.
PANEL WEIGHT MAX
24" Model 22 lb (10 kg)
15" Model 15 lb (7 kg)
Finish all sides of the custom panel. They will be visible
when the door is open.
A D-style handle is recommended. Locate the door handle
near the edge of the panel opposite the hinge and cen-
tered top to bottom. Stainless steel tubular and pro handles
are available through an authorized Sub-Zero dealer. For
local dealer information, visit the find a showroom section
of our website, subzero.com.
Door Panel
Stainless Steel Panel
Stainless steel panels are available through an authorized
Sub-Zero dealer. Stainless steel panels include a stainless
steel kickplate cover. The outdoor model requires the use
of a Sub-Zero stainless steel outdoor accessory panel. For
local dealer information, visit the find a showroom section
of our website, subzero.com.
Minimum ⁄" (3) reveals are required.
Questo manuale è adatto per i seguenti modelli
6
Indice
Lingue:
Altri manuali Sub-Zero Refrigeratore per vino
Sub-Zero
Sub-Zero Designer Series Manuale utente
Sub-Zero
Sub-Zero 424HAG/O-2 Manuale utente
Sub-Zero
Sub-Zero 430 Manuale utente
Sub-Zero
Sub-Zero DEU1550B/R Manuale utente
Sub-Zero
Sub-Zero DEU2450WL Manuale utente
Sub-Zero
Sub-Zero IW-30R Manuale utente
Sub-Zero
Sub-Zero 424 Manuale del proprietario
Sub-Zero
Sub-Zero Classic CL3050W/O/L Manuale utente
Sub-Zero
Sub-Zero 427 Manuale utente
Sub-Zero
Sub-Zero IW-18 Manuale utente
Sub-Zero
Sub-Zero 424FS Manuale utente
Sub-Zero
Sub-Zero 315W Manuale utente
Sub-Zero
Sub-Zero Designer Series Manuale utente
Sub-Zero
Sub-Zero Designer Series Manuale utente
Sub-Zero
Sub-Zero UW-24 Manuale utente
Sub-Zero
Sub-Zero ICBIW-18 Manuale utente
Sub-Zero
Sub-Zero 315W Manuale utente
Sub-Zero
Sub-Zero 427G Manuale utente
Sub-Zero
Sub-Zero WS-30 Manuale utente
Sub-Zero
Sub-Zero 400-2 Series Manuale di servizio
