SUGA SWBGFSA-0 Manuale utente
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 1
Model: SWBGFSA-0
WiFi/Bluetooth/GPS 3-in-1 Combo Module
User Guide
Version 1.0
Jun 2014
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 2
1 Hardware Installation ……………………………...….. 3
1.1 Me hani al Drawing ……………………………………….……… 3
1.2 Pins Assignment ………………………………………………….... 3
1.3 Hardware Installation Pro edures ……………………………..… 4
2 Software Installation ………………………….……….. 5
2.1 COM port he k …………………………………….........………… 5
2.2 Software Configuration Tools ……………………………………… 5
2.3 Configuration for GPS …………………………………………….. 7
2.4 Configuration for BT ………………………………………………. 8
2.5 Configuration for Wifi …………………………………………….. 10
3 Trouble-shooting …………………………..…….…….. 11
4 Disclaimer …………………………………..……...….. 13
5 Device Labelling …………………………….………….. 13
6 FCC Information …………………………….………….. 14
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 3
1. Hardware Installation
1.1 Me hani al Drawing
Figure1. Mechanical dimension
1.2 Pins Assignment
Please refer to the datasheet about the details of the pin assignment.
Pin# definition Des ription
1 ANT_WIFI_BT WIFI/BT RF input/output port
2, 13, 23 GND GND
14 VCC3.3V 3.3V power supply
3 ~ 8 SD_D[3 0], CMD, CLK SDIO data pins.
9 ~ 12 PCM_X PCM data pins
15 ~ 16 UART_TXD, RXD UART data pins
17, 19 PMU_EN, LNA_EN System enable pins
18 SYS_RST- System reset pin
20~22 IRQ_X Interrupt pins
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 4
1.3 Hardware Installation Pro edures
Example of Installation procedures
1. Disconnect from any power supply.
2. Solder firmly the module onto the host system board.
3. For best performance, have the Wifi+BT chip antenna located as far away as
possible from any metal.
4. Connect the GPS antenna to the module via coaxial cable to the GPS RF
connector on the module.
5. For best performance, have the GPS antenna located as far away as possible from
any metal and pointing upward to the sky.
6. Turn on the host unit and supply 3.3V+/-0.1V to the module.
Figure 2. Example of module installation to the host system.
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 5
2. Software Installation
2.1 COM port he k
Under Windows, run Device Manager. Check the physical COM port assignment. For
example as in below picture, the COM port is COM7.
2.2 Software Configuration Tools
(1) Run “Lab Tool for WiFi V1.30” confiuguration tool. Check that the virtual COM
port (WMT, BT, GPS) is same as those in below picture.
(2) Fill into the PHY port the correct physical COM port (COM7). Click Enable.
(3) Put the patch file “Patch_e3_20120405.bin” into any location in harddisk, e.g.
“ \C”.
(4) For BT/GPS, fill Virtual COM to be 31, click Open Port.
(5) Click Select > Select the patch file > Path. Wait until the log area reports
successful.
(6) Click BT or GPS to enable BT or GPS.
(7) Read MAC address if necessary.
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 6
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 7
2.3 Configuration for GPS
(1) Create a hyper-terminal under Windows. Select COM35. Configure 115200-8-N-1
to view GPS data.
(2) Open “GPS MNL Decoder”. Select Set/Unset, Enable/Disable to enable/disable
the GPS decoder.
(3) Wait a few seconds. GPS data will be given out to the hyper-terminal.
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 8
2.4 Configuration for BT
(1) Open “Lab Tool for Bluetooth V1.6”.
(2) Fill in 32 to COM port. Select Open.
(3) Configure BT package type, modulation, channel, etc.
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 9
Suga Electronics Limited
© Suga Electronics Limited. All Rights Reserved.
Information in this document is subject to change without prior notice.
P. 10
2.5 Configuration for Wifi
(1) Click Enable/Disable to enable/disable Wifi.
(2) Confirm that the log area reported successful.
(3) Configure desired channel, mode, etc.
Indice
