Summit Professional BIM24 Manuale utente

PROFESSIONAL

lce Maker

USER'MANUAL

Bll\/,24

IMPORTANT SA.FETY INSTRUCTIONS

/TWARNlNG,¡r' TO HËDUCE THE RISK OF FIRE,

" READ ALL INSTRUCTIONS BEFORE USING THE ICE MAKER.

. DANGEH OR WARNING: RISK OF CHILD ENTRAPN¡ENT.

CHILD ENTRAPMENTAND SUFFOCATION ARE NOT PROBLEMS OF THE PAST. JUNKED

OR ABANDONED APPLIANCES ARE STILL DANGEROUS, . - EVEN IF THEY WILL "JUST SIT

IN THE GARAGE A FEW DAYS."

. BEFOREYOUTHROWAWAYYOURICEMAKEF: TAKEOFFTHE DOOR. LEAVETHE

SHELVES IN PLACE SO THAT CHILDREN I\,4AY NOT EASILY CLIMB INSIDE.

. NEVER ALLOW CHILDREN TO OPERA].E, PLAY WITH, OR CRAWL INSIDE THE

APPLIANCE.

. NEVER CLEAN ICE MAKER PARTS WITH FLAIVN¡ABLE FLUIDS, THE FUMES CAN

CREATE A FIRE HAZARD OR EXPLOSION.

. DO NOT STORE OR USE GASOLINE OR ANY OTHER FLAMMABLE VAPORS AND LIOUIDS

IN THE VICINITY OF THIS OR ANY OTHER ICE MAKER, THE FUMES CAN CREATE A FIRE

HAZARD OR EXPLOSION.

SAVE THESE INSTRUCTIONS-

INSTALLATION INSTRUCTIONS

BEFORE USING YOUR ICE MAKER

RE[/OVE THE ËXTERIOR AND INTERIOR PACKING.

CHECK TO BE SURE YOU HAVE ALL OF THE FOLLOWING PARTS:

. 1 ICE BUCKET

. 1 PLASTIC SCOOP

. 25 FT. HOSE

. 1 INSTRUCTION MANUAL

BEFORE CONNECTING THE ICE MAKER TO THE POWER SOURCE, LET IT STAND UPRIGHT

FOR APPROXIMATELY 2 HOURS. THIS WILL REDUCE THE POSSIBILITY OF A MALFUNCTION

IN THE COOLING SYSTEN/ FROM HANDLING DURING TRANSPORTATION.

CLEAN THE INTERIOR SURFACE WITH LUKEWARM WATER USING A SOFT CLOTH.

INSTALLATION OF YOUR ICE MAKER

THIS APPLIANCE IS DESIGNED TO BË RECESSED OR BUILT.IN (FULLY RECESSED),

PLACE YOUR ICE MAKER ON A FLOOR THAT IS STRONG ENOUGH TO SUPPORT THE ICE

MAKER WHEN IT IS FULLY LOADED. RE[/EMBER THAT THE UNIT WILL BE SIGNIFICANTLY

HEAVIER ONCE lT lS FULLY LOADED. TO LEVEL YOUR ICE l\i|AKER, ADJUST THE LEG AT

THE FRONT OF THE ICE IVIAKER.

LOCATE THE ICE MAKER AWAY FROM DIRECT SUNLIGHTAND SOURCES OF HEAT (STOVE,

HEATER, RADTATOR, ETC.). DTRECT SUNLTGHT ÀilAy AFFECT THE ACRYL|C COATTNG AND

HEAT SOURCES MAY INCREASE ELECTRICAL CONSUMPTION, EXTREME COLD AMBIENT

TEMPERATURES MAY ALSO CAUSE THE ICE MAKER NOT TO PERFOBM PROPERLY.

AVOID LOCATING THE ICE I\¡AKER IN MOIST AREAS. TOO MUCII MO¡STURE IN THE AIR WILL

CAUSE FROST TO FORM QUICKLY ON THE EVAPORATOR REQUIRING.T/ORE FREQUENT

DEFROSTING OF THE ICE [/AKER.

PLUG THÊ ICE MAKER INTO AN EXCLUSIVE PROPERLY ¡NSTALLËD-GROUNDED WALL

ouTLET. DO NOT UNDER ANy CTRCUMSTANCES CUT OR REN/OVE THË THTRD (GROUND)

PRONG FROM THE POWER CORD, ANY QUESTIONS CONCERNING POWER AND OR

ELECTRICAL SI-IOCK, OR INJURY WI.IEN

USING YOUR ICE MAKER, FOLLOW THESE

GROUNDING SHOULD BE DIRECTED TOWARD A CERTIFIED ELECTRICIAN OR AN

AUTHORIZED AVANTI PRODUCTS SERVICE CENTER.

> ELECTRICALCONNECTION ¡/weRrult¡c,¡/

IMPROPER USE OF THE GROUNDED PLUG CAN RESULT IN THE RISK OF ELECTRICAL

SHOCK. IF THE POWER CORD IS DAMAGED, HAVE IT REPLACED BY AN AUTHORIZED

AVANTI PRODUCTS SERVICE CENTER.

o THIS ICE MAKER SHOULD BE PROPERLY GROUNDED FOR YOUR SAFETY. THE POWER

CORD OF THIS ICE MAKER IS EQUIPPED WITH A THREE.PRONG PLUG WHICH MATES WITH

STANDARD THREE PRONG WALL OUTLETS TO MINIMIZE THE POSSIBILITY OF ELECTRICAL

SHOCK.

. DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD GROUND PRONG

FROM THE POWER CORD SUPPLIED.

. NEVER USE AN EXTENSION CORD TO CONNECT POWER TO THE UNIT.

. NEVER USE A TWO-PRONG GROUNDING ADAPTER.

. WHERE A TWO-PRONG WALL RECEPTACLE lS ENCOUNTERED, CONTACT A QUALIFIED

ELECTRICIAN TO HAVE IT REPLACED WITH A 3-PRONG RECEPTACLE IN ACCORDANCE

WITH APPLICABLE ELECTRICAL CODES.

. THIS ICE MAKER FEQUIRES A STANDARD 1 15/120 VOLTS A.C,-/6OHZ ELECTRICAL OUTLET

WITH THREE-PRONG GROUND.

. THE CORD SHOULD BE SECURED BEHIND THE ICE MAKER AND NOT LEFT EXPOSED OR

DANGLING TO PREVENT ACCIDENTAL INJURY.

> EXTENSION CORD

BECALJSE OF POTEI'ITIAL SAFETY HAZARDS UNDER CERTAIN CONDITIONS, IT IS STRONGLY

RECOMMENDED THAT YOU DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.

HOWEVER, IF YOU MUST USE AN EXTENSION CORD IT IS ABSOLUTELY NECESSARY THAT IT

BE A UUCUL-LISTED, 3-WIRE GROUNDING TYPE APPLIANCE EXTENSION CORD HAVING A

GROUNDING TYPE PLUG AND OUTLET AND THAT THE ELECTRICAL RATING OF THE CORD BE

1 1 5 VOLTS AND AT LEAST 1 O AMPERES,

CONNECTING THE WATER SUPPLY

/wARNtNG,¡/

IMPROPER WATER LINE CONNECTION MAY RESULT IN FLOODING

YOU MUST USE A LICENSED PLUMBER

BEVIEW STATE AND LOCAL PLUMBING CODES BEFORE INSTALLATION

ALL THE NECESSARY HARDWARE IS NOT PROVIDED FOR INSTALLATION SO IT IS

NECESSARY TO HIRE A PROFESSIONAL LICENSED PLUMBER TO COMPLETE THE

INSTALLATION.

CONNECT TUBING (SUPPLIED WITH UNIT) TO THE NEAREST COLD WATER SOURCE.

CONNECT SUFFICIENT TUBING TO THE UNIT TO ALLOW THE APPLIANCE TO BE MOVED

FREELY FOR CLEANING AND SERVICE. ALSO MAKE SURE THAT THE TUBING IS NOT

PINCHED OR DAMAGED DURING TRANSPORTATION.

POSITION UNIT TO ALLOW FREE AIRFLOW THROUGH THE FRONT GRILL (SEE SKETCH 1).

WIPE OUT INSIDE OF UNIT AND ICE BUCKET WITH A DAMP CLOTH.

Þ BEV-E-B9I!.{8JIHE DOOB-SUILNG OF YOUH ICE MÄKEH

THIS APPLIANCE HAS THE CAPABILITY OF THE DOOR OPENING FROM EITHER THE LEFT OR

RIGHT SIDE, THE UNIT IS DELIVERED TO YOU WITH IHE DOOR OPENING FRO[/ THE LEFT

SIDE. SHOULD YOU DESIRE TO REVERSE THE OPENING DIRECTION, PLEASE CALL

CUSTON/,lER SERVICE FOR REVEBSAL INSTRUCTIONS,

OPERATING YOUR ICE MAKER

> lNlT!AL START:UP OPERATIoN

1. PLUG THE APPLIANCE INTO A 115/120V POLARIZED AND GROUNDED WALL ELECTRICAL

OUTLET,

2. PLACE THE ON-OFF SWITCH IN THE'ON'POSITION.

3. MAKE suRE THE WATER supply ts oN. AS sooN AS THE TNNER N4ECHANtstv.l REACHES

THE PROPER TEMPERATURE, THE ICEMAKER I/ECHANISI¡ WILL FILL THE MOLD WITH

WATER.

4. I-HE FIRST CUBES N/AY BE SIVALL BECAUSE OF AIR IN THE WATER LINE. LATER CUBES

WILL BE OF STANDARD CRESCENT N/OON TYPE SIZE.

5, APPROX¡MATE TIME FOR THE FIRST CYCLE lS BETWEEN 30-40 N/tNUTES.

6, EACH CYCLE APPROXIMATËLY WILL TAKE 140 ML OF WATER SO YOU SHOULD HAVE A

FULL TRAY, AFTER 1 ] HOURS,

IMPORTANT: THRAW AWAY ALL ICE CUBES MADE DURING TiE NNST 3 HOURS OF

OPENANAN.

WHEN THE ICE BUCKET IS FLJLL, THE ICE MAKING MECI1ANISN¡ WILL

AUTOMATICALLY SHUT OFF, HOWEVER THE SYSTEM WILL CONTINUE TO

COOL AND [/AINTAIN THE CUBES SUPPLY,

ICE DELIVERY MAY BE INTERRUPTED BY FAISING THE I\4ETAL ARM INTO

AN UPRIGHT POSIT|ON (sEE sKErcH 2)

IF THË ICEMAKER IS NOT USED REGULARLY, ¡T IS RECOMMENDED THAT

THE ICE BUCKET BE EIIPTIED PERIODICALLY TO INSURE FRESH ICE.

SOMETIMES THE CUBES IMAY APPEAR CLOUDY. THIS IS CAUSE OF NO CONCERN AND HAS

NOTHING TO DO WITH THË TASTE OR CHEIV¡CAL N/AKE-UP OF THE WATER.

THE FRONT GRILL SHOULD BF KEPT FREE OF DUST AND LINT TO PERN/IT FREE AìRFLOW.

THIS UNIT SHOULD BE DEFROSTED APPROXIMATELY EVERY 4-6 WEEKS OR WHEN FROST

ON THE ICE MAKER WALLS IS EXCESSIVE OR %'THICK. TO DEFROST, TURN THF UNIT OFF,

REIMOVE CUBES AND KËEP DOOR OPEN AT LEAST TWO INCHES,

CARE AND MAINTENANCE

CLEANING YOUR ICE MAKER

TURN THE SWITCH CONTROL TO'OFF', UNPLUG THE ICE N/AKER AND REMOVE BUCKET

WASH THE INSIDE WITH A WARIV WATER AND BAKING SODA SOLUTJON. THE SOLUT¡ON

SHOULD BE ABOUT 2 TABLESPOONS OF BAKING SODA TO A QUARI OF WATER

WASH THE BUCKET WITH A MILD DETERGENT SOLUTION,

THE OUTSIDE OF THE ICE IVAKER SHOULD BE CLEANED WìTH MILD DETERGENT AND

WARM WATER.

THE CONDENSER COILS SHOULD BE VACUUMED WHEN THEY ARE DUSTY OR DIRTY.

tlftf

r--1'. J--

ì----¡,- f

Ièf4YI

vYn)

SKETCH 2

CAUTION

FAILURE TO UNPLUG THE ICE MAKER COULD RESULT IN ELECTRICAL SHOCK OR

PERSONAL INJURY.

> POWER FAILURE

MOST POWER FAILURES ARE CORRECTED WITHIN A FEW HOUBS AND SHOULD NOT AFFECT

THE TEMPERATURE OF YOUR ICE IVAKER IF YOU MINIMIZE THE NUMBER OF TIMES THE DOOR

IS OPENED. IF THE POWER IS GOING TO BE OFF FOR A LONGER PERIOD OF TIME, YOU NEED

TO TAKE THE PROPER STEPS TO DISCONNECT YOUR APPLIANCE.

> VACATIONTIME/STORAGE

1. SHUTOFFWATERSUPPLYATTHEMAINWATERVALVE.

2. DISCONNECT THE WATER SUPPLY LINE FROM VALVE.

3. ALLOW UNIT TO RUN FOR AN HOUR OR TWO UNTIL ALL REIVAINING ICE CUBES HAVE

BEEN EJECTED.

4. DISCONNECT UNIT FROM MAIN POWER SOURCE.

5. DRY OUT EXCESS WATER FRON/ ICE MAKER ASSEMBLY

6. LEAVE THE DOOR OPEN AT LEAST TWO INCHES.

MOVING YOUR ICE MAKER

SECURELY TAPE DOWN ALL LOOSE ITEMS INSIDE YOUR ICE MAKER.

TURN THE LEVELING SCREWS UP TO THE BASE TO AVOID DAMAGE.

TAPE THE DOOR SHUT.

BE SURE THE ICE MAKER STAYS IN THE UPRIGHT POSITION DURING TRANSPORTATION.

ENERGY SAVING TIPS

+te rce MnXEn SHOULD BE LOCATED tN THE COOLEST AREA OF THE ROOM, AWAY FROÀ/

HEAT PRODUCING APPLIANCES OR HEATING DUCIS, AND OUT OF THE DIRECT

SUNLIGHT.

PROBLEMS WITHYOUR ICE MAKER?

YOU CAN SOLVE [/ANYCOIúMON ICE MAKER PROBLEMS ËASILY, SAVING YOU THE COSTOFA

POSSIBLE SERVICE CALL. TRY THE SUGGESTIONS BELOW TO SEE IF YOU CAN SOLVE THE

PROBLEM BEFORE CALLING THE SERVICER.

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE

ICE MAKER DOES NOT OPERATE. NOT PLUGGED IN.

THE CIRCUIT BREAKER TRIPPED OR A

BLOWN FUSE,

THE ICE MAKER POWER SWITCH IS SET AT

"oFF".

NOT PRODUCING ICE AIRFLOW TO FRONT GRILL BLOCKËD.

THE ICE IVAKER ARIV IS SET TO THË OFF

POSITION.

WATER SUPPLY IS TURNED OFF.

WATER LINE IS CRIMPED.

ICE I/AKER HAS EXCESSIVE FROST BUILD

UP.

COMPRESSOB TURNS ON AND OFF

FREOUENTLY. THE ROO[/ TEMPERATURE IS HOTTER THAN

NOR[/AL.

THE DOOB IS OPENED TOO OFTEN.

THE DOOR IS NOT CLOSED COMPLETELY.

THE DOOR GASKET DOES NOT SEAL

PROPERLY.

THE ICE MAKER DOES NOT HAVE THE

CORRECT CLEARANCES.

VIBRATIONS CHECK TO ASSURË THAT THE ICE MAKER IS

LEVEL.

THE ICE MAKER SEEMS TO MAKE TOO IVUCH

NOISE. THE RATTLING NOISË MAY COME FROM THE

FLOW OF THE REFRIGERANT, WHICH IS

NORMAL.

AS EACH CYCLE ENDS, YOU MAY HEAR

GURGLING SOUNDS CAUSED BY THE FLOW

OF REFRIGERANT IN YOUR ICE MAKER.

CONTRACTION AND EXPANSION OF THE

INSIDE WALLS MAY CAUSE POPPING AND

CRACKLING NOISES.

THE ICE MAKER IS NOT LEVEL.

THE DOOR WILL NOT CLOSE PROPERLY. THE ICE N/AKER IS NOT LEVEL.

ÏHE DOOR IS REVEFSED AND NOT

PROPERLY INSTALLED,

THE GASKET IS DIRTY

THE BUCKET IS OUT OF POSITION.

ICE CUBES ARE [/ELTED TOGETHEH ICE MAKER DOOR IS OPENED TOO OFTEN.

Indice

Altri manuali Summit Professional Macchina per il ghiaccio

Summit Professional

Summit Professional BIM25H34 Manuale utente

Manuali Macchina per il ghiaccio popolari di altre marche

Hoshizaki

Hoshizaki KMD-460MWJ Manuale utente

Sub-Zero

Sub-Zero 315I Istruzioni per l’uso

Unold

Unold 48945 Manuale utente

Kenmore

Kenmore 2217402A Manuale utente

Cornelius

Cornelius WM600 Istruzioni operative

GE XPIO43SCSS Manuale utente

Hoshizaki

Hoshizaki KMD-901MAH Manuale utente

Whynter

Whynter FIM-450HA Manuale utente

U-Line

U-Line UMCR014-SC01A Manuale di installazione

Andrew James

Andrew James AJ000522 Manuale utente

Scotsman

Scotsman CME1356 Manuale utente

Scotsman

Scotsman ACM 25 Manuale utente

Kärcher

Kärcher IP 120 Manuale utente

U-Line

U-Line SS1095 Manuale utente

Maytag

Maytag MIM1554WRS - Ice Maker Manuale utente

Hoshizaki

Hoshizaki KM-630MAH Manuale utente

Princess

Princess Yonanas Manuale utente

Unold

Unold 48946 Manuale utente