Sunlight Supply Eco 185 Manuale utente
Submersible Pump Instructions
Models: Eco 100 / Eco 185 / Eco 264 / Eco 396 / Eco 633 /
Eco 1056 / Eco 1267 / Eco 1584 / Eco 2245
Product: #728494 / #728300 / #728305 / #728310 / #728315 /
#728320 / #728325 / #728330 / #728333
®
www.sunlightsupply.com
Made in China
The EcoPlus submersible pumps are quality products, designed using the very latest
technological developments. The pumps are suitable for use in hydroponic systems, ponds,
aquariums, fountains and filter systems. The pumps have been developed on the basis of
the so-called synchronous technology, whereby the electrical parts are fully encapsulated in
epoxy resin.
USE
The pumps have an economical, powerful and reliable motor. The entire series are suitable
for installation on dry land for in-line use or submersibly into the water. The EcoPlus
submersible pumps are equipped with a ceramic shaft and therefore also suitable for use in
salt water.
OPERATION
Read these instructions very carefully before you start. NEVER let the pump run dry. Place
the pump at least 6 inches and no more than 3 feet below the water surface, on a stable
surface that is free of sludge, sand and other debris. Add fountain extension pipes so that the
fountain head is above the surface of the pond. (1) Turn the flow control clockwise to increase
flow and counter-clockwise to reduce flow. (2) Water bell nozzle is adjusted by moving the
head higher for small bell and lower for a wider bell shape.
SAFETY REQUIREMENTS
The power supply must comply with the specifications on the product. The national code
requires that a GFCI (Ground Fault Circuit Interrupter) be utilized in the branch circuit,
which supplies electrical power to the EcoPlus pump and all other electrical aquarium or
hydroponic equipment. NEVER pull the pump by the power cord and NEVER remove the
pump from the water by pulling on the power cord. NEVER remove the power plug or shorten
the cable. Your warranty is void if you do not comply with the operation and instructions
noted above. Keep the electrical connection (plug and wall socket) dry.
The pump is not suitable for use in swimming pools, swimming ponds or other situations
where persons could make bodily contact with the water. Always unplug the power cord
before cleaning the pump or carrying out water maintenance.
MAINTENANCE & CLEANING
The EcoPlus submersible pumps do not require lubrication or special maintenance. The
following maintenance and cleansing will improve the pumps performance and life.
Cleaning: When the flow is visibly reduced you may want to clean the pump. Unplug the
pump’s power cord first, then remove the pump form the water (Do NOT use the cord to lift
the pump). Firmly pull the pre-filter cage from the pump motor. Remove the pre-filter sponge
and wash thoroughly in fresh water. A blocked sponge will reduce the pump flow rate and
performance.
Regular Maintenance: Remove the impeller cover by turning counterclockwise to release
lock. Firmly pull away from the pump motor. Carefully remove impeller locator and complete
Submersible Pump Instructions
MODEL VOLT FREQ AMPS
(A)
OUTPUT
(L/H)
OUTPUT
(G/H)
H-MAX
(M)
H-MAX
(FOOT)
DIMENSIONS
(MM)
DIMENSIONS
(INCH)
ECO-66 120V 60Hz .059 284 75 0.75 2.5 49x55x45.5 1.9x2.1x1.7
ECO-100 120V 60Hz .085 380 100 0.90 3.0 78x42x55 3x1.6x2.1
ECO-132 120V 60Hz .23 500 132 1.22 4.0 49x67.2x60 1.9x2.6x2.3
ECO-185 120V 60Hz .22 600 158 1.20 4.0 143x54x75 5.6x2.1x2.9
ECO-264 120V 60Hz .23 1100 290 1.95 6.5 160x65x90 6.2x2.5x3.5
ECO-396 120V 60Hz .30 1500 396 1.95 6.5 165x80x115 6.4x3.1x4.5
ECO-633 120V 60Hz .45 2250 594 2.40 7.5 185x80x110 7.2x3.1x4.3
ECO-1056 120V 60Hz .74 4100 1083 2.80 9.0 200x110x140 7.8x4.3x5.5
ECO-1267 120V 60Hz 1.60 5100 1347 4.50 13.5 230x102x160 9.0x4.0x6.2
ECO-1500* 120V 60Hz 1.7 5700 1505 6.10 20.3 176x124x222 6.9x4.9x8.7
ECO-1584 120V 60Hz 2.046 6200 1638 4.00 12.5 238x130x176 9.3x5.1x6.9
ECO-2245 120V 60Hz 2.05 8200 2166 5.00 16.5 270x148x178 10.6x5.8x7
Eco Submersible Pump Technical Information
®
2 7
* Not UL listed
impeller. Wash parts with fresh water carefully. Once you have cleaned the pump, reassemble
it in reverse order. Cleaning frequency will depend on the conditions under which the pump
is used.
Do not allow the pump to freeze up in the winter. Make sure to remove the pump from a pond
or fountain and store it in a frost-free place.
WARRANTY
This product has a warranty of one year for any defects in materials or workmanship.
Warranty is NOT VALID if the pump is not properly used, neglected, or there is a lack of
maintenance or accidental damage either to the pump or to the impeller or impeller shaft. If
the pump fails due to manufacturing fault within this warranty period, the pump will either be
repaired or replaced free of charge. Please return the pump to the place of purchase with the
original bill receipt.
The manufacturer or distributor shall not be held responsible for any damages cause by
defective components or materials, or for loss incurred because of the interruption of services
or any consequential, or incidental damages or expenses arising from the manufacture, sale,
use or misuses of this product. The manufacturer shall not be held responsible for any loss
of fish, plants or other livestock as a result of any failure or defect of this product.
This warranty excludes the sponge prefilter and impeller which may require replacing
annually.
• Use with 120 volt power source.
• The pump is provided with a thermal protector that temporarily switches off the
pump in case of overheating and the pump may automatically restart.
IMPORTANT SAFETY INSTRUCTIONS
Warning: To guard against injury, basic safety precautions should be observed, including
the following:
1. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
2. DANGER: To avoid possible electric shock, special care should be taken since water is
employed in the use of aquarium, hydroponic systems and pond equipment. For each
of the following situations, do not attempt repairs by yourself; return the appliance to an
authorized service facility for service or discard the appliance:
• If the appliance shows any sign of abnormal water leakage, immediately unplug it
from the power source. (Submersible equipment only)
• Carefully examine the appliance after installation. It should not be plugged in if there
is water on parts not intended to be wet.
• Do not operate any appliance if it has a damaged cord or plug, or if it is
malfunctioning or has been dropped or damaged in any manner.
CAUTION
THERMALLY PROTECTED ENCLOSURE TYPE 3 FOR INDOOR
AND OUTDOOR USE.
THIS PUMP HAS BEEN EVALUATED FOR USE WITH WATER
O N LY.
WARNING
RISK OF ELECTRIC SHOCK - THIS PUMP HAS NOT BEEN
INVESTIGATED FOR USE IN SWIMMING POOL OR MARINE
AREAS.
TO REDUCE THE RISK OF ELECTRIC SHOCK, INSTALL ONLY
ON A CIRCUIT PROTECTED BY A GROUND-FAULT CIRCUIT-
INTERRUPTER (GFCI).
RISK OF ELECTRIC SHOCK - THIS PUMP IS SUPPLIED WITH A
GROUNDING CONDUCTOR GROUNDING-TYPE ATTACHMENT
PLUG. TO REDUCE THE RISK OF ELECTRIC SHOCK, BE
CERTAIN THAT IT IS CONNECTED ONLY TO A PROPERLY
GROUNDED, GROUNDING-TYPE RECEPTACLE.
TO REDUCE THE RISK OF ELECTRIC SHOCK, SEE
INSTRUCTION MANUAL FOR PROPER INSTALLATION.
INSTALLATION INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF ELECTRIC SHOCK, USE ONLY ON
PORTABLE SELF CONTAINED FOUNTAINS NO LARGER THAN
5 FEET IN ANY DIMENSION.
36
• To avoid the possibility of the appliance plug or outlet getting wet, position aquarium
stand and tank to one side of a wall-mounted outlet to prevent water from dripping
onto outlet or plug. A “drip loop” shown in the figure to the right, should be arranged
by the user for each cord connecting an aquarium appliance to an outlet. The “drip
loop” is the part of the cord below the level of the
outlet, or the connector is an extension cord is
used, to prevent water traveling along the cord
and coming in contact with the outlet. If the plug
or outlet does get wet, DON’T unplug the cord.
Disconnect the fuse or circuit breaker that supplies power to the appliance. Then,
unplug and examine for presence of water in the outlet.
3. Close supervision is necessary when any appliance is used by or near children.
4. To avoid injury, do not contact moving parts or hot parts such as heater, reflectors,
lamp bulbs, and the like.
5. Always unplug an appliance from an outlet when not in use, before putting on or
taking off parts, and before cleaning. Never yank cord to pull plug from outlet. Grasp
the plug and pull to disconnect.
6. Do not use an appliance for other than intended use. The use of attachments not
recommended or sold by the appliance manufacturer may cause unsafe conditions.
7. Do not install or store the appliance where it will be exposed to the weather or
temperatures below freezing.
8. Make sure appliance mounted on a tank is securely installed before operating it.
9. Read and observe all the important notices on the appliances.
10. If an extension cord is necessary, a cord with a proper rating should be used. A cord
rated for less than 120 volts may overheat. Care should be taken to arrange the cord so
that it will not be tripped over or pulled.
11. This appliance has no user serviceable parts.
12. SAVE THESE INSTRUCTIONS.
PARTS DESCRIPTION
5
4
Questo manuale è adatto per i seguenti modelli
8
Indice
Altri manuali Sunlight Supply Pompa dell'acqua
Manuali Pompa dell'acqua popolari di altre marche
Sykes AmeriPumps
Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi
DUROMAX
DUROMAX XP WX Series Manuale utente
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Manuale utente
Franklin Electric
Franklin Electric IPS Manuale utente
Xylem
Xylem e-1532 Series Manuale utente
Milton Roy
Milton Roy PRIMEROYAL Manuale utente