SUNPOW OT-MD06 Manuale utente
01
Thank you for choosing SUNPOW OT-MD06 metal
detector.
Please read this manual carefully and become familiar
with the function before using. After reading, please
keep it safe for future reference.
TABLE OF CONTENTS
Specifications
Easy Assembly
Installing the Batteries
Panel (LCD and Button)
Testing Guide
Basic Operations
Cautions
Trouble Shooting Guide
Warm Tips
02
----------------------------
---------------
------------------------
---------------------
---------------
--------------------------
----------------------------------
---------------
--------------------------------
03
03-06
06-07
07-09
09-11
11-15
16
16-17
18
03
SPECIFICATIONS
EASY ASSEMBLY
•Operation Mode:
Motion Mode:
①ALL-METAL
②DISC
Non-motion Mode: PINPOINT
•Coins Depth Indication: 5 grades
•Sensitivity Control: 9 grades
•Target Metals Discrimination: 9 kinds(0 to 99) double
digits
•Signal Strength Indication: 5 grades
•Sound Frequency: 3 kinds of frequency indicating different
metals
•Volume Indication: 3 grades
•LCD Backlight: White
•Battery Indication: 4 grades
•Auto power-off: Auto-shutdown without operating after 15 mins
•Search Coil: Waterproof search coil
•Earphone Jack: 1/8 inch earphone jack
•Power Supply: Two 9V alkaline batteries
Assembling the metal detector is easy and don't need special tools.
Just follow these steps:
The structure is shown in the Pic1 below.
Search Coil
Lower Stem Middle Stem
Control Box
Bolt
Bracket
Search Coil Upper Stem
Pic1
04
1.Loosen the bolt on the lower stem, take down the bolt. Install the
lower stem on the search coil, and lock it tightly. (See Pic2)
Attention please: Make sure the silver button is facing the
opposite direction of the search coil.
3.Loosen the lock nut on the other end of the middle stem.
Keep pressing the silver button on the upper stem and insert
the upper stem into the other end of the middle stem. (See Pic4).
Pic2
Silver Button
Lower Stem
Bolt
Fixing Knob
Search Coil
Pic3
2.Loosen the lock nut on the middle stem and press the silver
button on the lower stem, then insert lower stem’s silver button into
the small hole of the middle stem. (See Pic3)
Lower Stem
Silver Button Middle Stem
Small Hole
Lock Nut
Pic4 Small Hole
Lock Nut
Silver Button
Upper Stem
Middle Stem
05
4.Keep pressing the silver button on the bracket, insert it to the
upper stem and then install the bracket. (See Pic5).
5.Align the control box with the groove and push it to the end,
then push it up to the end, and finally tighten the screws.
Note: If the screw cannot be screwed in, the control box is
installed incorrectly. (See Pic6).
Pic6
Pic5
Small Hole Silver Button
Bracket
Control Box
Screw
Groove
Push
Upper Stem
06
6.Adjust the length that the lower stem inserts to the middle stem.
and you can adjust the total length of the stem to make you feel
comfortable with your arm straight when detecting.
7.Wrap the cable of the search coil around the aluminum stem with
moderate elasticity so that it doesn’t wobble. Plug the cable plug
into the lower right of the control box, aiming at the slot and
plugging into the end and tighten. (See Pic7).
Note: When you want to unplug the cable plug, do not
pull the cable, please pull the plug.
Pic7
Pic8
INSTALLING THE BATTERIES
Follow these steps to install the batteries.
1.Turn off before installing the batteries.
2.Remove the battery cover.
3.Place two 9V alkaline batteries into the battery compartment,
matching the polarity symbols (+ and -) indicated inside.
4.Let the ribbon under the battery. (See Pic8).
9V 9V
OPEN
OPE N
Plug
07
•Cautions:
1.Do not mix the old and new batteries or different types of batteries.
2.Only use new alkaline batteries of required size.
3.If you don't plan to use the detector for a long time,
please remove the battery from the battery case.
Batteries may leak chemicals that can destroy elec-
tronic parts.
Warning: Dispose of old batteries promptly and properly. Never bury
or burn them.
PANEL (LCD and Button)
Pic9
LCD
•Mode Cursor: Indicate the operation mode. There are 3 modes.
(①A-M ②DISC ③P/P).
•Target ID Cursor: Divided into 9 categories. It is used to
indicate the target metals.
P/P Key
Backlight
Earphone
A-M Key
LCD Display
Power
Disc Key
Sens(+-)Key Vol(+-)Key
Disc Cursor
( )Key
08
Button
•Digital ID Cursor/Pinpoint Cursor: Two digits of 01 to 99
accurately indicate the metal material. It also acts as a P/P
cursor, when PP showing, it enters the pinpoint mode.
•Coin Depth Cursor: Divided into 5 grades. Indicates the
approximate depth of 25￠silver coin in neutral soil.
•Volume Cursor: Indicates the volume.
•Sensitivity Indication Cursor: Divided into 9 grades.
Sensitivity is highest when all cursor light.
•Battery Power Cursor: Divided into 4 grades, indicating
battery power. When the battery pattern is flashing, which
means the battery should be replaced.
Power Button: As on/off power supply.
A-M Button: Press A-M button, the detector enter all metal
mode.In this mode the detector will detect all metal.
(DISC)Button: Press DISC button and the detector enters
DISC mode.In this mode you can arbitrarily eliminate certain
kinds of metal and the detector won't detect it.
(P-P) Button: Press the button, and the detector will
convert to PINPOINT mode to locate the target accurately.
Press the "P-P" button once again to exit the
PINPOINT mode.
Backlight Button: As the on/off key of LCD backlight.
09
SENS“+,-” Button: In A-M or DISC mode,press these
two buttons to increase or decrease the detection
sensitivity.At thesame time, there will be corresponding
indication on the LCD.
VOL “+,-” Button: Volume adjustment button. Press
these two buttons to adjust the volume of the alarm.
The volume level is from1 to 3.
TESTING GUIDE
Pic10
2.Turn on
Press the POWER button, the detector will sound 3 kinds of
tones (high,medium,low) and all LCD patterns will be lit for a
moment. And the detector is set by default last shutdown.
Button: In DISC mode, press these two buttons.
The circle cursor outside the target metal object will move
left or right,and then press DISC button to eliminate or
select the metal object.At the same time, there will be
corresponding indication on the LCD.
1.Lay the Detector
Put the detector on a wooden or plastic table and let the search
coil stretch out of the table about 0.98 ft.(See Pic10).
Note: Keep away from walls, ceilings and floors, then turn off
all kinds of electrical appliances that will cause electromagnetic
interference. Remove watches and rings from hands.
10
Note:Each boot will enter the all metal mode by
default. If you used the DISC mode last time, please
press the DISC button to switch to the DISC mode,
then the LCD will show your previous settings.
3.Sensitivity Adjustment
Generally, to avoid the interference of surrounding electrical
appliances, power lines and other electrical equipment indoors.
We recommend setting the detector sensitivity to level 7.Press
the "+, -" keys to adjust the sensitivity.
4.ALL METAL Mode Test
The metal detector will enter all metal mode by default when you
turn on it every time. You can also press the "A-M" key to enter
this mode.In this mode, all metals can be detected.
5.DISC Mode Test
Press the DISC button and the DISC cursor will light up, thus
entering disc mode. In disc mode, press “< , >” buttons. The
circle cursor outside the target metal object will move left or
right, and then press disc to eliminate or select the metal object.
At the same time, there will be corresponding indication on the LCD.
For example, if 4 kinds of metals are rejected, such as iron, p-tab,
S-CAP and 10 ￠, the corresponding icon will disappear. The
detector will not give an alarm to the corresponding metal.
Scan your existing metal samples (such as 5 ￠, 1 ￠, 25 ￠, etc.)
about 2.76in to 3.9in above the search coil. The detector will appear
3 situations:
①The detector will make different sounds in turn.
②The depth cursor indicates level 3 or 4.
③The target cursor flashes respectively. The numeric cursor
displays the corresponding number. As shown in the table:
Indice
Manuali Rilevatore di metalli popolari di altre marche
Steinberg Systems
Steinberg Systems SBS-MD-12 Manuale utente
GOLDEN MASK
GOLDEN MASK 5 Manuale utente
Grizzly
Grizzly YM 203 Manuale utente
Fisher Research Labs
Fisher Research Labs 1280-X Aquanaut Manuale utente
Treasure Cove
Treasure Cove Vibra-Probe 560 Manuale utente
Accurate Locators
Accurate Locators XL16 IMAGER Manuale utente