SUNTEC Klimatronic Progress 7.0 plus Manuale utente

Progress plus

Instruction manual

Figure 1 Figure 2

Figure 3 Figure 4

Figure 5 Figure 6 Figure 7

Figure 8 Figure 10

Please read this user’s manual carefully to ensure proper use, maintenance and installation.

SPECIFICATION

1. Do not use the unit on a socket under repairs or not installed properly.

2. Do not use the unit, follow these precautions:

A: Near to source of fire.

B: An area where oil is likely to splash.

C: An area exposed to direct sunlight.

D: An area where water is likely to splash.

E: Near a bath, a shower or a swimming pool.

3. Never insert your fingers, into the air outlet. Take special care to warn children of these dangers.

4. Keep the unit upward while transport and storage, for the compressor locates properly.

5. Before cleaning the air-conditioner, always turn off and disconnect the power supply.

6. When moving the air-conditioner, always turn off and disconnect the power supply, and move it slowly.

7. To avoid the possibility of fire disaster, the air-conditioner shall not be covered.

8. All the air-conditioner sockets must comply with the local electric safety requirements. If necessary, please check it for the requirements.

9. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

10. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a

hazard.

Notes:

—If any parts damage, please contact the dealer or a designated repair shop;

—In case of any damage, please turn off the air switch, disconnect the power supply, and contact the dealer or a designated repair shop;

—In any case, the power cord shall be firmly grounded.

—To avoid the possibility of danger, if power cord is damaged, please turn off the air switch and disconnect the power supply. It must be replaced

from the dealer or a designated repair shop.

This air conditioner must be stored and transported upright, otherwise you may cause irreparable compressor damage. In case of doubt let

the unit rest for at least 24 hours before you start it.

Model No.

Klimatronic Progress 7.0 plus

Klimatronic Progress 9.0 plus

Klimatronic Progress 12.0 plus

Volt

230V~50Hz AC

Power consumption (EN14511)

780 W

980 W

1340 W

Cooling capacity

2050 W

2600 W

3500 W

Air Flow Volume

320 m³/h

450 m³/h

Dehumification

1,0 Liter/h

1,2 Liter/h

1,5 Liter/h

Refrigerant

R410a

Measurements (BxHxT)

41,5 x 72,1 x 29,1 cm

Net Weight

23 kg

24 kg

25,5 kg

Name of Parts, Figure 1 Spare Parts, Figure 2

1. rear cover 5. caster 9. exhaust pipe

2. air inlet 6. power line 10. flat fixing clip

3. front cover 7. air inlet 11. square fixing clip

4. operation panel 8. air inlet

Appearance and Function of Control Panel, Figure 3

12. POWER Button 15. timer POWER button 18. water full indicator lamp

13. temperature –button 16. temperature + button 19. fan speed adjustment button

14. operation mode button 17. signal receiver window 20. LED Window

Operation Display, Figure 4

1. Auto Mode Icon

2. Fan Speed

3. Cooling Mode

4. Temp. and Timer Setting

5. Timer on

6. Temperature °C

7. Dry Mode Icon

Appearance and Function of Remote Controller, Figure 5

21. POWER Button; press this button will turn the machine on or off

22. Temperature setting button; this button is used to set the room temperature.

Each key press increases the room temperature about 1°C.

23. Speed Button; Press this button will choose high, middle or low ventilation speed.

24. Timer button; press to set the timer on or off

25. Temperature setting button; this button is used to set the room temperature.

Each key press reduces the room temperature about 1°C.

26. Mode Button; press this button will choose the function auto cooling, cooling, or dry.

Operation Introduction, Figure 6

Before starting operations in this section:

1. Find a place where there is power supply nearby.

2. As shown in the figure on the right, install the exhaust hose, and adjust the window position well.

3. Insert the power cord into an grounded AC230V/50Hz socket;

4. Press the POWER button to turn on the air-conditioner.

5. After switching on, or over, the ventilator operates, but the compressor starts later. Cooling effect may require a further 10 minutes.

Before using

Notice:

1. Operation temperature range:

Check up whether the exhaust hose has been mounted properly.

Cautions for cooling and dehumidifying operations:

-When using functions on cooling and dehumidifying, keep an interval of at least 3 minutes between turning on and turning off.

-Power supply meets the requirements.

-The socket is forAC use.

-Do not share one socket with other appliances.

-Power supply is AC230V，50Hz

2. Cooling operation

-Press the “Mode” button till the “Cool” icon (seeFigure4)appears.

-Press the “Temp+”or“ Temp-”buttontoselectadesiredroomtemperature.(16°C-31°C)

-Press the “Fan Speed” button to select wind speed.

-Aftersetting, thecurrentroom temperatureisshownon thedisplay.

3. AutoMode

- Press the “Mode” button till the “Auto” icon (seeFigure4)appears.

-Press the “Temp+”or“ Temp-”buttontoselectadesiredroomtemperature.

-After setting, the roomtemperatureis showninthedisplay.

-inAutomode,thefanspeedischangeable.

-Automodemeans,thattheunitwill turnoff, whenthedesiredroomtemperature is reachedandit willturnon,if the roomtemperature changes again.

-If the room temperature is equal to or above 18 ° C, the unit can cool in the automatic mode. At lower temperatures the device will protect the compressor by

automaticallyswitching intoventilationmode.

4. Dehumidifyingoperation

Press the “Mode” button till the “Dehumidify Indicator Lamp” (see Figure 4)blinks

-Theunitwillsetthetemperatureandthefanspeedbyitself.

5. Timeroperation

TimerONsettingcooling:

-Whentheair-conditioner is OFF, press the “Timer” button andselectadesiredONtimethroughthetemperatureandtimesettingbuttons.

-ONtimecanberegulatedatanytimein0-24hours.

-Press the “Timer” button to confirm your setting.

Timer OFF settingcooling:

-Whentheair-conditioner ON, press “Timer” button and select a desired OFF time through the temperature and time setting buttons.

-OFFtimecanbe regulated at anytimein 0-24hours.

-Press the “Timer” button to confirm your setting.

TimerOnsettingdehumidifying:

-Choosethedehumidifyingmodeas describedin4.

- Whentheair-conditionerOFF, press “Timer” button and select a desired ON timethrough the temperature and timesettingbuttons.

- Timecanberegulatedatanytimein0-24hours.

- Press the “Timer” button toconfirmyoursetting.

TimerOFFsetting dehumidifying:

-Whentheair-conditionerON,pressthe“Timer” button and select a desired OFF time through the temperature and time setting buttons.

-OFFtimecanbe regulated at anytimein 0-24hours.

- Press the “Timer” button to confirm your setting.

6. Drainage

-When you plan to leave this unit unused for a long time, please remove the rubber blockage from the drainage hole at the bottom of unit, and

connect a drain hose to the lower fixing clip. All the water in the water tank will drain outside.

-If water pump is damaged, continuous drainage can be used, and under this condition, the water pump is not activated. The unit can also

work well.

-If water pump is damaged, intermittent drainage can also be used. Under this condition, when the water full indicator lamp lights up, please

connect a drain hose to the lower fixing clip, then all the water in the water tank will drain outside. The unit can also work well.

Installation Explanations

-A removal air-conditioner shall be installed in the flat and empty place all around.

Don’t block the air outlet, and the required distance around should be at least 30cm.

-Theunitshouldnotbeinstalledindry-cleaner.

Introduction to Exhaust Hose Installation

A) Temporary installation

1. Twist both ends of the exhaust hose into the square fixing clip and the flat fixing clip.

2. Insert the square fixing clip into openings at back of the air conditioner.

Hook the left side of the adapter into the opening at the rear cover. Conduct the right side at the

rear cover and press it down until the Adapter engages.

3. Put the other end of the exhaust hose to the near windowsill.

Maintenance Explanations

Declaration:

1) Before cleaning, be sure to disconnect the unit from any electric supply outlet;

2) Do not use gasoline or other chemicals to clean the unit;

3) Do not wash the unit directly;

4) If the conditioner is damaged, please contact the dealer or repair shop.

1. Air Filter

-If the air filter becomes clogged with dust/dirt, the air filter should be cleaned once every two weeks.

-Dismounting

Open the air inlet grille and take off air filter.

-Cleaning

Clean the air filter with neural detergent in lukewarm（40°C）and dry it up in the shade.

Mounting

Putting the air filter into the inlet grille, replace the components as they were.

-Clean the Air-conditioner Surface

First clean the surface with a neutral detergent and wet cloth, and then wipe it with a dry cloth.

Troubleshooting

Troubles

Possible Causes

Suggested Remedies

Unit does not start when pressing POWER

button

- Water full indicator lamp blinks, and water tank

is full.

Dump the water out of the water tank.

- Room temperature is higher than the setting

temperature. (Electric heating mode)

Reset the temperature

- Room temperature is lower than the setting

temperature. (Cooling mode)

Reset the temperature

Not cool enough

- The doors or windows are not closed.

Make sure all the windows and doors are

closed.

- There are heat sources inside the room.

Remove the heat sources if possible

- Exhaust air hose is not connected or blocked.

Connect or clean the exhaust air hose.

- Temperature setting is too high.

Reset the temperature

- Air inlet is blocked.

Clean the air inlet.

Noisy

- The ground is not level or not flat enough

Place the unit on a flat, level ground if possible

- The sound comes from the flowing of the

refrigerant inside the air conditioner

It is normal.

several operation icons will blink

- at a room temperature higher or equal 18°C, Auto mode and cooling mode will work together.

If the room temperature is equal to or above 18 ° C, the unit can cool in the automatic mode. At

lower temperatures the device will protect the compressor by automatically switching into ventilation

mode.

E0 Code

There is evidence that this error massage is

caused to a room temperature which is too high.

It can also caused by a temporary fault at the

rating between incoming- and outcoming

temperature.

Please turn off the unit and turn in on after 30

minutes. If this fault is everlasting, your

PROGRESS unit should be checked by a

professional.

E2 Code

Water tank full

Please empty the water tank.

Can I switch the PROGRESS unit on

immediately after unpacking it?

No.

The PROGRESS unit must be placed upright for

at least 24 hours after every transport.

Otherwise the compressor may be damaged

and there is no capacity.

When switching on the PROGRESS unit I sense

a smell. What should I do?

Production-related cause or incorrect storage of

unit at e.g. dusty areas.

Odour development can arise on first use and

after a longer period of non-use by storing in

unsuitable areas (e.g. dusty areas).

Run the unit for ½ a day. The smell will

disappear after a while. In the case of intensive

odour development, air the room.

Can I operate the PROGRESS unit WITHOUT

the extract air hose?

Yes, but only in dehumidification mode.

To achieve temperature adjustments, surplus

coldness must be discharged.

At which intervals should the activated carbon

filter of the PROGRESS unit be replaced?

To use the purpose of the filter fully, it should be

replaced every 6 months.

How can I increase the efficiency of the

PROGRESS unit?

External circumstances exist which may impact

the efficiency of the PROGRESS unit. Room

insulation, use of wall/window adapter, ratio of

window space (solar radiation), operation of

electrical units in the room (EDP), presence of

several persons in the room. You can increase

the efficiency of the PROGRESS unit

accordingly by adjusting such circumstances.

Compressor does not activate

Depending on ambient temperatures and

PROGRESS unit type it may take approx. 10

minutes after starting the compressor until the

cooling capacity is reached.

PROGRESS unit deactivates.

On reaching the set required temperature, the

PROGRESS unit switches off automatically.

Check manual setting of the required

temperature as well as the TIMER setting.

How is the m² or m³ data of the manufacturer

calculated

The m² or m³ data of the manufacturer for the

various PROGRESS units are average values

related to a room height of 2.5 metres. It must be

considered that such data can be clearly

underscored or exceeded under certain

circumstances. Circumstances which work

against efficiency of the PROGRESS units

include e.g. bad insulation of the building, large

window areas, south facing, attic apartment,

many additional heat sources, such as e.g.

number of persons, EDP, light, kitchen units,

washing units etc.

PROGRESS unit does not cool correctly

You achieve the most effective and economical

cooling comfort if you already cool the room to

be cooled when the room temperature is not yet

heated up. Air conditioners operate more

effectively if the temperature is to be maintained.

To drastically cool the air and inventory in a fully

heated room requires much more time and

energy.

EC-Declaration of Conformity

The unit complies with the essential health and safety requirements of the European Union. The EC declaration of conformity is the basis for the CE

marking of this unit.

ERP REGULATION

This high-quality single-channel portable air conditioning unit is in accordance with the rules and regulations of the European Union, in particular the

new ERP Regulation 626/2011 to a "local air conditioner."

REFRIGERANT

(CE) N 842/2006: This air conditioner contains the refrigerant R410A. The amount of refrigerant is less than 1kg, and is in a closed cooling circuit. The

coolant does have zero ozone depletion potential, but is a so-called greenhouse gases under the Kyoto Protocol and may thus contribute to global

warming, if it is released to the atmosphere. Therefore only trained technicians with refrigerant certificate make a filling or emptying. Suntec your air